GitLab

TZC_400_REGION_ATTR_FILTER_BIT_ALL is a simple constant definition, so
it can't get the real filter number to construct the bit flag for all
existing filters. If the platform doesn't have 4 filters, passing
FILTER_BIT_ALL to tzc400_configure_region() will cause assertion or
misconfiguration. So adjust the bit flag against the real filter
number.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Ie5c48303485f3b5015772961ee7c34746121ee84

ESPI register offset should also be shifted right by REG##R_SHIFT to
keep consistent.

It is not a functional issue, for GICD_OFFSET_64() is only used for
GICD_IROUTER<E>, and IROUTER_SHIFT is 0.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I76eee5c50e4300890e78e80bddde135ce88daa2d

Add debug log for the maximum supported INTID of SPI and eSPI on the
current GIC implementation.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Ie45ab1d85b39658c4ca4bc54ee433ac44e41d03f

The GICv3 architecture allows GICD_TYPER.ITLinesNumber to be 31, so
the maximum possible value for num_ints is 1024. The value must be
limited to (MAX_SPI_ID + 1), or GICD_OFFSET() will consider it as ESPI
INTID and return wrong register address.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Iddcb83d3e5d241b39f4176c19c2bceaa2c3dd653

In function gicv3_spis_config_defaults(), the variable num_ints is set
to (maximum SPI INTID + 1), while num_eints is set to (maximum ESPI
INTID). It introduces not only inconsistency to the code, but also
logical bug in the "for" loops, for the INTID of num_eints is also
valid and the check should be inclusive.

Fix this by setting num_eints to (maximum ESPI INTID + 1) as well.

Fix similar issues in gicv3_distif_save() and
gicv3_distif_init_restore().
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I4425777d17e84e85f38853603340bd348640154f

RESTORE/SAVE_GICD_EREGS uses (int_id - (MIN_ESPI_ID - MIN_SPI_ID)) to
get the context array index for ESPI, which will override the space of
standard SPI starting from (MIN_SPI_ID + MIN_SPI_ID).

However, using TOTAL_SPI_INTR_NUM to replace the above MIN_SPI_ID
cannot totally fix the issue, for TOTAL_SPI_INTR_NUM is not well
aligned and the array index will be rounded down by the shifting
operation if being shifted more than 2 bits. It will cause buffer
override again when the existing maximum SPI reaches 1019.

So round up TOTAL_SPI_INTR_NUM with (1 << REG##R_SHIFT) for GICD
context arrays.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I5be2837c42f381a62f8d46a4ecd778009b1fe059

In function gicv3_rdistif_probe(), line #1322 implies
gicv3_driver_data->mpidr_to_core_pos() may be null, but the original
code uses this interface to get current CPU index unconditionally.

It is better to use MPIDR to probe GICR which does not depend on
gicv3_driver_data->mpidr_to_core_pos().
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I64add055385040fe0a56b977e2299608e2309a6e

Usually, C has no problem up-converting types to larger bit sizes. MISRA
rule 10.7 requires that you not do this, or be very explicit about this.
This resolves the following required rule:

    bl1/aarch64/bl1_context_mgmt.c:81:[MISRA C-2012 Rule 10.7 (required)]<None>
    The width of the composite expression "0U | ((mode & 3U) << 2U) | 1U |
    0x3c0U" (32 bits) is less that the right hand operand
    "18446744073709547519ULL" (64 bits).

This also resolves MISRA defects such as:

    bl2/aarch64/bl2arch_setup.c:18:[MISRA C-2012 Rule 12.2 (required)]
    In the expression "3U << 20", shifting more than 7 bits, the number
    of bits in the essential type of the left expression, "3U", is
    not allowed.

Further, MISRA requires that all shifts don't overflow. The definition of
PAGE_SIZE was (1U << 12), and 1U is 8 bits. This caused about 50 issues.
This fixes the violation by changing the definition to 1UL << 12. Since
this uses 32bits, it should not create any issues for aarch32.

This patch also contains a fix for a build failure in the sun50i_a64
platform. Specifically, these misra fixes removed a single and
instruction,

    92407e73        and     x19, x19, #0xffffffff

from the cm_setup_context function caused a relocation in
psci_cpus_on_start to require a linker-generated stub. This increased the
size of the .text section and caused an alignment later on to go over a
page boundary and round up to the end of RAM before placing the .data
section. This sectionn is of non-zero size and therefore causes a link
error.

The fix included in this reorders the functions during link time
without changing their ording with respect to alignment.

Change-Id: I76b4b662c3d262296728a8b9aab7a33b02087f16
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>

In the function gicv2_set_spi_routing, the signed value proc_num is cast
to unsigned int before being compared to other unsigned values in two
assert calls.  The value proc_num can be a negative value, and once the
negative value is cast to unsigned it becomes a very large number which
will trigger the assert.  This patch changes the assert cast so that the
unsigned values are cast to signed instead, keeping the same functionality
but allowing proc_num to be negative.

This bug can be seen when running the SDEI RM_ANY routing mode test in
TFTF on the Juno platform.

This patch also makes the usage of the proc_num variable in other gicv2
functions more clear.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: If1b98eebb00bd9b73862e5e995e5e68c168170a6

And from crash_console_flush.

We ignore the error information return by console_flush in _every_
place where we call it, and casting the return type to void does not
work around the MISRA violation that this causes. Instead, we collect
the error information from the driver (to avoid changing that API), and
don't return it to the caller.

Change-Id: I1e35afe01764d5c8f0efd04f8949d333ffb688c1
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>

A GICv3 interrupt controller will be instantiated for a certain number
of cores. This will result in the respective number of GICR frames. The
last frame will have the "Last" bit set in its GICR_TYPER register.

For platforms with a topology unknown at build time (the Arm FPGAs, for
instance), we need to learn the number of used cores at runtime, to size
the GICR region in the devicetree accordingly.

Add a generic function that iterates over all GICR frames until it
encounters one with the "Last" bit set. It returns the number of cores
the GICv3 has been configured for.

Change-Id: I79f033c50dfc1c275aba7122725868811abcc4f8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch fixes violation of Rules 10.1, 10.4,
11.9 and 13.2 reported by MISRA-2012 scan.

Change-Id: Ibe9190cb0f26ae85d9a31db8e92fbd32f1740e25
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch fixes defects 10.3, 10.4, 10.7, 20.7
reported by MISRA-2012 scan and adds braces for
conditional statements according to the TF-A
coding style.

Change-Id: If84ed31cdd55bc8e7cdd2a5f48c0dacc25792112
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

The Arm GIC-Clayton IP has the same power management requirements as
the GIC-600, when it comes to powering up the redistributors before
using them.

Add the IIDR value to the existing list of implementations requiring
the power sequence.

Change-Id: Ib965dfe278c40a4fff94f65a8d445c27a2ae6fd2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch moves all GICv2 driver files into new added
'gicv2.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.

NOTE: Usage of 'drivers/arm/gic/common/gic_common.c' file
is now deprecated and platforms with GICv2 driver need to
be modified to include 'drivers/arm/gic/v2/gicv2.mk' in
their makefiles.

Change-Id: Ib10e71bdda0e5c7e80a049ddce2de1dd839602d1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch adds the IIDR value for GIC600-AE to the gicv3_is_gic600()
helper function. This helps platforms supporting this version of the
GIC600 interrupt controller to function with the generic GIC driver.

Verified with tftf-validation test suite

******************************* Summary *******************************
> Test suite 'Framework Validation'
                                                                Passed
> Test suite 'Timer framework Validation'
                                                                Passed
=================================
Tests Skipped : 0
Tests Passed  : 6
Tests Failed  : 0
Tests Crashed : 0
Total tests   : 6
=================================
NOTICE:  Exiting tests.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I518ae7b56f7f372e374e453287d76ca370fc3574

Cleaned up confused naming between TB_FW and FW_CONFIG.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I9e9f6e6ca076d38fee0388f97d370431ae067f08

It is desired to have the peripheral writes completed to clear the
interrupt condition and de-assert the interrupt request to GIC before
EOI write. Failing which spurious interrupt will occurred.

A barrier is needed to ensure peripheral register write transfers are
complete before EOI is done.

GICv2 memory mapped DEVICE nGnR(n)E writes are ordered from core point
of view. However these writes may pass over different interconnects,
bridges, buffers leaving some rare chances for the actual write to
complete out of order.

GICv3 ICC EOI system register writes have no ordering against nGnR(n)E
memory writes as they are over different interfaces.

Hence a dsb can ensure from core no writes are issued before the previous
writes are *complete*.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Change-Id: Ie6362009e2f91955be99dca8ece14ade7b4811d6

The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.

This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.

Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

To support compatibility with previous GICv3 driver version
this patch:
- restores original API for gicr_read_ipriority() and
gicr_wrtite_ipriority() functions;
- adds accessor functions for GICR_XXX0,1 registers, e.g.
GICR_IGROUPR0, GICR_ICFGR0, GICR_ICFGR1, etc.

Change-Id: I796a312a61665ff384e3d9de2f4b3c60f700b43b
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

GIC-Clayton supports multichip operation mode which allows it to connect
upto 16 other GIC-Clayton instances. GIC-Clayton's multichip programming
and operation remains same as GIC-600 with a minor change in the
SPI_BLOCKS and SPI_BLOCK_MIN shifts to accommodate additional SPI
ranges. So identify if the GIC v4 extension is enabled by the platform
makefile and appropriately select the SPI_BLOCKS and SPI_BLOCK_MIN
shifts.

Change-Id: I95fd80ef16af6c7ca09e2335539187b133052d41
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

This patch adds support for GICv4 extension.
New `GIC_ENABLE_V4_EXTN` option passed to gicv3.mk makefile
was added, and enables GICv4 related changes when set to 1.
This option defaults to 0.

Change-Id: I30ebe1b7a98d3a54863900f37eda4589c707a288
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch provides support for GICv3.1 extended PPI and SPI
range. The option is enabled by setting to 1 and passing
`GIC_EXT_INTID` build flag to gicv3.mk makefile.
This option defaults to 0 with no extended range support.

Change-Id: I7d09086fe22ea531c5df51a8a1efd8928458d394
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch moves all GICv3 driver files into new added
'gicv3.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
The patch adds GICv3 driver configuration flags
'GICV3_IMPL', 'GICV3_IMPL_GIC600_MULTICHIP' and
'GICV3_OVERRIDE_DISTIF_PWR_OPS' described in
'GICv3 driver options' section of 'build-option.rst'
document.

NOTE: Platforms with GICv3 driver need to be modified to
include 'drivers/arm/gic/v3/gicv3.mk' in their makefiles.

Change-Id: If055f6770ff20f5dee5a3c99ae7ced7cdcac5c44
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch provides separation of GICD, GICR accessor
functions and adds new macros for GICv3 registers access
as a preparation for GICv3.1 and GICv4 support.
NOTE: Platforms need to modify to include both
'gicdv3_helpers.c' and 'gicrv3_helpers.c' instead of the
single helper file previously.

Change-Id: I1641bd6d217d6eb7d1228be3c4177b2d556da60a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

The cpu index was wrongly checked causing it to assert always.
Since this code path is exercised only during TF test "NODE_HW_STAT",
which queries Power state from SCP, this bug was not detected earlier.

Change-Id: Ia25cef4c0aa23ed08092df39134937a2601c21ac
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.

Change-Id: I7a23327394d142af4b293ea7ccd90b843c54587c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Instead, pass back the error to the calling function. This allows
platform code to fall back to another PSCI implementation if
scpi_wait_ready() or a later SCPI command fails.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ib4411e63c2512857f09ffffe1c405358dddeb4a6

On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.

Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.

Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

This patch removes unnecessary header file includes
discovered by Coverity HFA option.

Change-Id: I2827c37c1c24866c87db0e206e681900545925d4
Signed-off-by: Zelalem <zelalem.aweke@arm.com>

The Secure Configuration Register is 64-bits in AArch64 and 32-bits in
AArch32. Use u_register_t instead of unsigned int to reflect this.

Change-Id: I51b69467baba36bf0cfaec2595dc8837b1566934
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

NOTE for platform integrators:
   API `plat_psci_stat_get_residency()` third argument
   `last_cpu_idx` is changed from "signed int" to the
   "unsigned int" type.

Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.

2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent

Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.

Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c

The SCU connects one to four Cortex-A5/Cortex-A9 processors
to the memory system through the AXI interfaces.

The SCU functions are to:
- maintain data cache coherency between the Cortex-A5/Cortex-A9
  processors
- initiate L2 AXI memory accesses
- arbitrate between Cortex-A5/Cortex-A9 processors requesting
  L2 accesses
- manage ACP accesses.

Snoop Control Unit will enable to snoop on other CPUs caches.
This is very important when it comes to synchronizing data between
CPUs. As an example, there is a high chance that data might be
cache'd and other CPUs can't see the change. In such cases,
if snoop control unit is enabled, data is synchoronized immediately
between CPUs and the changes are visible to other CPUs.

This driver provides functionality to enable SCU as well as enabling
user to know the following
- number of CPUs present
- is a particular CPU operating in SMP mode or AMP mode
- data cache size of a particular CPU
- does SCU has ACP port
- is L2CPRESENT

Change-Id: I0d977970154fa60df57caf449200d471f02312a0
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>

As supporting architectures aside from AArch32 and AArch64 is not a
concern, keeping identical definitions in two places for a large part
of the libc seems counterproductive

The int128 types were left un-unified as __int128 is not supported by
gcc on AArch32
Signed-off-by: Bence Szépkúti <bence.szepkuti@arm.com>
Change-Id: Idf08e6fab7e4680d9da62d3c57266ea2d80472cf

Change-Id: Ia120bcaacea3a462ab78db13f84ed23493033601
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>

Arm's GIC-600 features a Power Register (GICR_PWRR),
which needs to be programmed to enable redistributor
operation. Section 3.6.1 in the GIC-600 TRM describes
the power-up and power-down sequence in pseudo code,
which deviates from the current TF-A implementation
in drivers/arm/gic/v3/gic600.c.
For powering on a redistributor, the pseudo code suggests
to loop over the whole sequence (check for transition,
write request bit) instead of just looping over the
ready bit read as TF-A does in gic600_pwr_on().
This patch fixes GIC-600 power up sequence according
to the TRM.

Change-Id: I445c480e96ba356b69a2d8e5308ffe6c0a97f45b
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Add support to configure GIC-600's multichip routing table registers.
Introduce a new gic600 multichip structure in order to support platforms
to pass their GIC-600 multichip information such as routing table owner,
SPI blocks ownership.

This driver is currently experimental and the driver api may change in
the future.

Change-Id: Id409d0bc07843e271ead3fc2f6e3cb38b317878d
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

Instead of retry polling, timer of 1ms is used to poll
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: I7e028dc68138d2888e3cf0cbed744f5e6bc6ff42

Currently for Armv7 plaforms the quotient calculated in pl011
uart init code is moved to register r1.

This patch moves the quotient to register r2 as done for other
platforms in the udiv instruction. Value of register r2 is then
used to calculate the values for IBRD and FBRD register

Change-Id: Ie6622f9f0e6d634378b471df5d02823b492c8a24
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>