GitLab

The current PSCI implementation can apply certain optimizations upon the
assumption that all PSCI participants are cache-coherent.

  - Skip performing cache maintenance during power-up.

  - Skip performing cache maintenance during power-down:

    At present, on the power-down path, CPU driver disables caches and
    MMU, and performs cache maintenance in preparation for powering down
    the CPU. This means that PSCI must perform additional cache
    maintenance on the extant stack for correct functioning.

    If all participating CPUs are cache-coherent, CPU driver would
    neither disable MMU nor perform cache maintenance. The CPU being
    powered down, therefore, remain cache-coherent throughout all PSCI
    call paths. This in turn means that PSCI cache maintenance
    operations are not required during power down.

  - Choose spin locks instead of bakery locks:

    The current PSCI implementation must synchronize both cache-coherent
    and non-cache-coherent participants. Mutual exclusion primitives are
    not guaranteed to function on non-coherent memory. For this reason,
    the current PSCI implementation had to resort to bakery locks.

    If all participants are cache-coherent, the implementation can
    enable MMU and data caches early, and substitute bakery locks for
    spin locks. Spin locks make use of architectural mutual exclusion
    primitives, and are lighter and faster.

The optimizations are applied when HW_ASSISTED_COHERENCY build option is
enabled, as it's expected that all PSCI participants are cache-coherent
in those systems.

Change-Id: Iac51c3ed318ea7e2120f6b6a46fd2db2eae46ede
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch introduces the PSCI Library interface. The major changes
introduced are as follows:

* Earlier BL31 was responsible for Architectural initialization during cold
boot via bl31_arch_setup() whereas PSCI was responsible for the same during
warm boot. This functionality is now consolidated by the PSCI library
and it does Architectural initialization via psci_arch_setup() during both
cold and warm boots.

* Earlier the warm boot entry point was always `psci_entrypoint()`. This was
not flexible enough as a library interface. Now PSCI expects the runtime
firmware to provide the entry point via `psci_setup()`. A new function
`bl31_warm_entrypoint` is introduced in BL31 and the previous
`psci_entrypoint()` is deprecated.

* The `smc_helpers.h` is reorganized to separate the SMC Calling Convention
defines from the Trusted Firmware SMC helpers. The former is now in a new
header file `smcc.h` and the SMC helpers are moved to Architecture specific
header.

* The CPU context is used by PSCI for context initialization and
restoration after power down (PSCI Context). It is also used by BL31 for SMC
handling and context management during Normal-Secure world switch (SMC
Context). The `psci_smc_handler()` interface is redefined to not use SMC
helper macros thus enabling to decouple the PSCI context from EL3 runtime
firmware SMC context. This enables PSCI to be integrated with other runtime
firmware using a different SMC context.

NOTE: With this patch the architectural setup done in `bl31_arch_setup()`
is done as part of `psci_setup()` and hence `bl31_platform_setup()` will be
invoked prior to architectural setup. It is highly unlikely that the platform
setup will depend on architectural setup and cause any failure. Please be
be aware of this change in sequence.

Change-Id: I7f497a08d33be234bbb822c28146250cb20dab73

This patch moves the PSCI services and BL31 frameworks like context
management and per-cpu data into new library components `PSCI` and
`el3_runtime` respectively. This enables PSCI to be built independently from
BL31. A new `psci_lib.mk` makefile is introduced which adds the relevant
PSCI library sources and gets included by `bl31.mk`. Other changes which
are done as part of this patch are:

* The runtime services framework is now moved to the `common/` folder to
  enable reuse.
* The `asm_macros.S` and `assert_macros.S` helpers are moved to architecture
  specific folder.
* The `plat_psci_common.c` is moved from the `plat/common/aarch64/` folder
  to `plat/common` folder. The original file location now has a stub which
  just includes the file from new location to maintain platform compatibility.

Most of the changes wouldn't affect platform builds as they just involve
changes to the generic bl1.mk and bl31.mk makefiles.

NOTE: THE `plat_psci_common.c` FILE HAS MOVED LOCATION AND THE STUB FILE AT
THE ORIGINAL LOCATION IS NOW DEPRECATED. PLATFORMS SHOULD MODIFY THEIR
MAKEFILES TO INCLUDE THE FILE FROM THE NEW LOCATION.

Change-Id: I6bd87d5b59424995c6a65ef8076d4fda91ad5e86

The "end power level" value passed as the 3rd argument to the
psci_cpu_on_start() function is not used so this patch removes it.

Change-Id: Icaa68b8c4ecd94507287970455fbff354faaa41e

This patch introduces some debug assertions in the function
psci_cpu_on_start() to check the arguments it receives are
valid.

Change-Id: If4d23c9f668fb46f2d18c5e2ed1929498cc6736b

When a CPU is powered down using PSCI CPU OFF API, it disables its caches
and updates its `aff_info_state` to OFF. The corresponding cache line is
invalidated by the CPU so that the update will be observed by other CPUs
running with caches enabled. There is a possibility that another CPU
which has been trying to turn ON this CPU via PSCI CPU ON API,
has already seen the update to `aff_info_state` and proceeds to update
the state to ON_PENDING prior to the cache invalidation. This may result
in the update of the state to ON_PENDING being discarded.

This patch fixes this issue by making sure that the update of `aff_info_state`
to ON_PENDING sticks by reading back the value after the cache flush and
retrying it if not updated. The patch also adds a dsbish() to
`psci_do_cpu_off()` to ensure ordering of the update to `aff_info_state`
prior to cache line invalidation.

Fixes ARM-software/tf-issues#349

Change-Id: I225de99957fe89871f8c57bcfc243956e805dcca

On the ARMv8 architecture, cache maintenance operations by set/way on the last
level of integrated cache do not affect the system cache. This means that such a
flush or clean operation could result in the data being pushed out to the system
cache rather than main memory. Another CPU could access this data before it
enables its data cache or MMU. Such accesses could be serviced from the main
memory instead of the system cache. If the data in the sysem cache has not yet
been flushed or evicted to main memory then there could be a loss of
coherency. The only mechanism to guarantee that the main memory will be updated
is to use cache maintenance operations to the PoC by MVA(See section D3.4.11
(System level caches) of ARMv8-A Reference Manual (Issue A.g/ARM DDI0487A.G).

This patch removes the reliance of Trusted Firmware on the flush by set/way
operation to ensure visibility of data in the main memory. Cache maintenance
operations by MVA are now used instead. The following are the broad category of
changes:

1. The RW areas of BL2/BL31/BL32 are invalidated by MVA before the C runtime is
   initialised. This ensures that any stale cache lines at any level of cache
   are removed.

2. Updates to global data in runtime firmware (BL31) by the primary CPU are made
   visible to secondary CPUs using a cache clean operation by MVA.

3. Cache maintenance by set/way operations are only used prior to power down.

NOTE: NON-UPSTREAM TRUSTED FIRMWARE CODE SHOULD MAKE EQUIVALENT CHANGES IN
ORDER TO FUNCTION CORRECTLY ON PLATFORMS WITH SUPPORT FOR SYSTEM CACHES.

Fixes ARM-software/tf-issues#205

Change-Id: I64f1b398de0432813a0e0881d70f8337681f6e9a

This patch reworks the PSCI generic implementation to conform to ARM
Trusted Firmware coding guidelines as described here:
https://github.com/ARM-software/arm-trusted-firmware/wiki

This patch also reviews the use of signed data types within PSCI
Generic code and replaces them with their unsigned counterparts wherever
they are not appropriate. The PSCI_INVALID_DATA macro which was defined
to -1 is now replaced with PSCI_INVALID_PWR_LVL macro which is defined
to PLAT_MAX_PWR_LVL + 1.

Change-Id: Iaea422d0e46fc314e0b173c2b4c16e0d56b2515a

This commit does the switch to the new PSCI framework implementation replacing
the existing files in PSCI folder with the ones in PSCI1.0 folder. The
corresponding makefiles are modified as required for the new implementation.
The platform.h header file is also is switched to the new one
as required by the new frameworks. The build flag ENABLE_PLAT_COMPAT defaults
to 1 to enable compatibility layer which let the existing platform ports to
continue to build and run with minimal changes.

The default weak implementation of platform_get_core_pos() is now removed from
platform_helpers.S and is provided by the compatibility layer.

Note: The Secure Payloads and their dispatchers still use the old platform
and framework APIs and hence it is expected that the ENABLE_PLAT_COMPAT build
flag will remain enabled in subsequent patch. The compatibility for SPDs using
the older APIs on platforms migrated to the new APIs will be added in the
following patch.

Change-Id: I18c51b3a085b564aa05fdd98d11c9f3335712719

There used to be 2 warm reset entry points:

 - the "on finisher", for when the core has been turned on using a
   PSCI CPU_ON call;

 - the "suspend finisher", entered upon resumption from a previous
   PSCI CPU_SUSPEND call.

The appropriate warm reset entry point used to be programmed into the
mailboxes by the power management hooks.

However, it is not required to provide this information to the PSCI
entry point code, as it can figure it out by itself. By querying affinity
info state, a core is able to determine on which execution path it is.
If the state is ON_PENDING then it means it's been turned on else
it is resuming from suspend.

This patch unifies the 2 warm reset entry points into a single one:
psci_entrypoint(). The patch also implements the necessary logic
to distinguish between the 2 types of warm resets in the power up
finisher.

The plat_setup_psci_ops() API now takes the
secure entry point as an additional parameter to enable the platforms
to configure their mailbox. The platform hooks `pwr_domain_on`
and `pwr_domain_suspend` no longer take secure entry point as
a parameter.

Change-Id: I7d1c93787b54213aefdbc046b8cd66a555dfbfd9

The state-id field in the power-state parameter of a CPU_SUSPEND call can be
used to describe composite power states specific to a platform. The current PSCI
implementation does not interpret the state-id field. It relies on the target
power level and the state type fields in the power-state parameter to perform
state coordination and power management operations. The framework introduced
in this patch allows the PSCI implementation to intepret generic global states
like RUN, RETENTION or OFF from the State-ID to make global state coordination
decisions and reduce the complexity of platform ports. It adds support to
involve the platform in state coordination which facilitates the use of
composite power states and improves the support for entering standby states
at multiple power domains.

The patch also includes support for extended state-id format for the power
state parameter as specified by PSCIv1.0.

The PSCI implementation now defines a generic representation of the power-state
parameter. It depends on the platform port to convert the power-state parameter
(possibly encoding a composite power state) passed in a CPU_SUSPEND call to this
representation via the `validate_power_state()` plat_psci_ops handler. It is an
array where each index corresponds to a power level. Each entry contains the
local power state the power domain at that power level could enter.

The meaning of the local power state values is platform defined, and may vary
between levels in a single platform. The PSCI implementation constrains the
values only so that it can classify the state as RUN, RETENTION or OFF as
required by the specification:
   * zero means RUN
   * all OFF state values at all levels must be higher than all RETENTION
     state values at all levels
   * the platform provides PLAT_MAX_RET_STATE and PLAT_MAX_OFF_STATE values
     to the framework

The platform also must define the macros PLAT_MAX_RET_STATE and
PLAT_MAX_OFF_STATE which lets the PSCI implementation find out which power
domains have been requested to enter a retention or power down state. The PSCI
implementation does not interpret the local power states defined by the
platform. The only constraint is that the PLAT_MAX_RET_STATE <
PLAT_MAX_OFF_STATE.

For a power domain tree, the generic implementation maintains an array of local
power states. These are the states requested for each power domain by all the
cores contained within the domain. During a request to place multiple power
domains in a low power state, the platform is passed an array of requested
power-states for each power domain through the plat_get_target_pwr_state()
API. It coordinates amongst these states to determine a target local power
state for the power domain. A default weak implementation of this API is
provided in the platform layer which returns the minimum of the requested
power-states back to the PSCI state coordination.

Finally, the plat_psci_ops power management handlers are passed the target
local power states for each affected power domain using the generic
representation described above. The platform executes operations specific to
these target states.

The platform power management handler for placing a power domain in a standby
state (plat_pm_ops_t.pwr_domain_standby()) is now only used as a fast path for
placing a core power domain into a standby or retention state should now be
used to only place the core power domain in a standby or retention state.

The extended state-id power state format can be enabled by setting the
build flag PSCI_EXTENDED_STATE_ID=1 and it is disabled by default.

Change-Id: I9d4123d97e179529802c1f589baaa4101759d80c

This patch removes the assumption in the current PSCI implementation that MPIDR
based affinity levels map directly to levels in a power domain tree. This
enables PSCI generic code to support complex power domain topologies as
envisaged by PSCIv1.0 specification. The platform interface for querying
the power domain topology has been changed such that:

1. The generic PSCI code does not generate MPIDRs and use them to query the
   platform about the number of power domains at a particular power level. The
   platform now provides a description of the power domain tree on the SoC
   through a data structure. The existing platform APIs to provide the same
   information have been removed.

2. The linear indices returned by plat_core_pos_by_mpidr() and
   plat_my_core_pos() are used to retrieve core power domain nodes from the
   power domain tree. Power domains above the core level are accessed using a
   'parent' field in the tree node descriptors.

The platform describes the power domain tree in an array of 'unsigned
char's. The first entry in the array specifies the number of power domains at
the highest power level implemented in the system. Each susbsequent entry
corresponds to a power domain and contains the number of power domains that are
its direct children. This array is exported to the generic PSCI implementation
via the new `plat_get_power_domain_tree_desc()` platform API.

The PSCI generic code uses this array to populate its internal power domain tree
using the Breadth First Search like algorithm. The tree is split into two
arrays:

1. An array that contains all the core power domain nodes

2. An array that contains all the other power domain nodes

A separate array for core nodes allows certain core specific optimisations to
be implemented e.g. remove the bakery lock, re-use per-cpu data framework for
storing some information.

Entries in the core power domain array are allocated such that the
array index of the domain is equal to the linear index returned by
plat_core_pos_by_mpidr() and plat_my_core_pos() for the MPIDR
corresponding to that domain. This relationship is key to be able to use
an MPIDR to find the corresponding core power domain node, traverse to higher
power domain nodes and index into arrays that contain core specific
information.

An introductory document has been added to briefly describe the new interface.

Change-Id: I4b444719e8e927ba391cae48a23558308447da13

This patch introduces new platform APIs and context management helper APIs
to support the new topology framework based on linear core position. This
framework will be introduced in the follwoing patch and it removes the
assumption that the MPIDR based affinity levels map directly to levels
in a power domain tree. The new platforms APIs and context management
helpers based on core position are as described below:

* plat_my_core_pos() and plat_core_pos_by_mpidr()

These 2 new mandatory platform APIs are meant to replace the existing
'platform_get_core_pos()' API. The 'plat_my_core_pos()' API returns the
linear index of the calling core and 'plat_core_pos_by_mpidr()' returns
the linear index of a core specified by its MPIDR. The latter API will also
validate the MPIDR passed as an argument and will return an error code (-1)
if an invalid MPIDR is passed as the argument. This enables the caller to
safely convert an MPIDR of another core to its linear index without querying
the PSCI topology tree e.g. during a call to PSCI CPU_ON.

Since the 'plat_core_pos_by_mpidr()' API verifies an MPIDR, which is always
platform specific, it is no longer possible to maintain a default implementation
of this API. Also it might not be possible for a platform port to verify an
MPIDR before the C runtime has been setup or the topology has been initialized.
This would prevent 'plat_core_pos_by_mpidr()' from being callable prior to
topology setup. As a result, the generic Trusted Firmware code does not call
this API before the topology setup has been done.

The 'plat_my_core_pos' API should be able to run without a C runtime.
Since this API needs to return a core position which is equal to the one
returned by 'plat_core_pos_by_mpidr()' API for the corresponding MPIDR,
this too cannot have default implementation and is a mandatory API for
platform ports. These APIs will be implemented by the ARM reference platform
ports later in the patch stack.

* plat_get_my_stack() and plat_set_my_stack()

These APIs are the stack management APIs which set/return stack addresses
appropriate for the calling core. These replace the 'platform_get_stack()' and
'platform_set_stack()' APIs. A default weak MP version and a global UP version
of these APIs are provided for the platforms.

* Context management helpers based on linear core position

A set of new context management(CM) helpers viz cm_get_context_by_index(),
cm_set_context_by_index(), cm_init_my_context() and cm_init_context_by_index()
are defined which are meant to replace the old helpers which took MPIDR
as argument. The old CM helpers are implemented based on the new helpers to
allow for code consolidation and will be deprecated once the switch to the new
framework is done.

Change-Id: I89758632b370c2812973a4b2efdd9b81a41f9b69

As per Section 4.2.2. in the PSCI specification, the term "affinity"
is used in the context of describing the hierarchical arrangement
of cores. This often, but not always, maps directly to the processor
power domain topology of the system. The current PSCI implementation
assumes that this is always the case i.e. MPIDR based levels of
affinity always map to levels in a power domain topology tree.

This patch is the first in a series of patches which remove this
assumption. It removes all occurences of the terms "affinity
instances and levels" when used to describe the power domain
topology. Only the terminology is changed in this patch. Subsequent
patches will implement functional changes to remove the above
mentioned assumption.

Change-Id: Iee162f051b228828310610c5a320ff9d31009b4e

This patch optimizes the invocation of the platform power management hooks for
ON, OFF and SUSPEND such that they are called only for the highest affinity
level which will be powered off/on. Earlier, the hooks were being invoked for
all the intermediate levels as well.

This patch requires that the platforms migrate to the new semantics of the PM
hooks.  It also removes the `state` parameter from the pm hooks as the `afflvl`
parameter now indicates the highest affinity level for which power management
operations are required.

Change-Id: I57c87931d8a2723aeade14acc710e5b78ac41732

This patch creates a copy of the existing PSCI files and related psci.h and
platform.h header files in a new `PSCI1.0` directory. The changes for the
new PSCI power domain topology and extended state-ID frameworks will be
added incrementally to these files. This incremental approach will
aid in review and in understanding the changes better. Once all the
changes have been introduced, these files will replace the existing PSCI
files.

Change-Id: Ibb8a52e265daa4204e34829ed050bddd7e3316ff

In the debug build of the function get_power_on_target_afflvl(), there is a
check to ensure that the CPU is emerging from a SUSPEND or ON_PENDING state.
The state is checked without acquiring the lock for the CPU node. The state
could be updated to ON_PENDING in psci_afflvl_on() after the target CPU has
been powered up. This results in a race condition which could cause the
check for the ON_PENDING state in get_power_on_target_afflvl() to fail.
This patch resolves this race condition by setting the state of the target
CPU to ON_PENDING before the platform port attempts to power it on. The
target CPU is thus guaranteed to read the correct the state. In case
the power on operation fails, the state of the CPU is restored to OFF.

Fixes ARM-software/tf-issues#302

Change-Id: I3f2306a78c58d47b1a0fb7e33ab04f917a2d5044

This patch implements conditional checks in psci_smc_handler() to verify
that the psci function invoked by the caller is supported by the platform
or SPD implementation. The level of support is saved in the 'psci_caps'
variable. This check allows the PSCI implementation to return an error
early.

As a result of the above verification, the checks performed within the psci
handlers for the pm hooks are now removed and replaced with assertions.

Change-Id: I9b5b646a01d8566dc28c4d77dd3aa54e9bf3981a

This patch allows the platform to validate the power_state and
entrypoint information from the normal world early on in PSCI
calls so that we can return the error safely. New optional
pm_ops hooks `validate_power_state` and `validate_ns_entrypoint`
are introduced to do this.

As a result of these changes, all the other pm_ops handlers except
the PSCI_ON handler are expected to be successful. Also, the PSCI
implementation will now assert if a PSCI API is invoked without the
corresponding pm_ops handler being registered by the platform.

NOTE : PLATFORM PORTS WILL BREAK ON MERGE OF THIS COMMIT. The
pm hooks have 2 additional optional callbacks and the return type
of the other hooks have changed.

Fixes ARM-Software/tf-issues#229

Change-Id: I036bc0cff2349187c7b8b687b9ee0620aa7e24dc

This patch replaces the internal psci_save_ns_entry() API with a
psci_get_ns_ep_info() API. The new function splits the work done by the
previous one such that it populates and returns an 'entry_point_info_t'
structure with the information to enter the normal world upon completion
of the CPU_SUSPEND or CPU_ON call. This information is used to populate
the non-secure context structure separately.

This allows the new internal API `psci_get_ns_ep_info` to return error
and enable the code to return safely.

Change-Id: Ifd87430a4a3168eac0ebac712f59c93cbad1b231

This patch moves the check for valid CPU state during
PSCI_CPU_ON to before the non secure entry point is programmed
so as to enable it to return early on error.

Change-Id: I1b1a21be421e2b2a6e33db236e91dee8688efffa

This patch removes the non-secure entry point information being passed
to the platform pm_ops which is not needed. Also, it removes the `mpidr`
parameter for  platform pm hooks which are meant to do power management
operations only on the current cpu.

NOTE: PLATFORM PORTS MUST BE UPDATED AFTER MERGING THIS COMMIT.

Change-Id: If632376a990b7f3b355f910e78771884bf6b12e7

This patch implements the following cleanups in PSCI generic code:

1. It reworks the affinity level specific handlers in the PSCI implementation
   such that.

   a. Usage of the 'rc' local variable is restricted to only where it is
      absolutely needed

   b. 'plat_state' local variable is defined only when a direct invocation of
      plat_get_phys_state() does not suffice.

   c. If a platform handler is not registered then the level specific handler
      returns early.

2. It limits the use of the mpidr_aff_map_nodes_t typedef to declaration of
   arrays of the type instead of using it in function prototypes as well.

3. It removes dangling declarations of __psci_cpu_off() and
   __psci_cpu_suspend(). The definitions of these functions were removed in
   earlier patches.

Change-Id: I51e851967c148be9c2eeda3a3c41878f7b4d6978

This patch pulls out state management from the affinity level specific handlers
into the top level functions specific to the operation
i.e. psci_afflvl_suspend(), psci_afflvl_on() etc.

In the power down path this patch will allow an affinity instance at level X to
determine the state that an affinity instance at level X+1 will enter before the
level specific handlers are called. This will be useful to determine whether a
CPU is the last in the cluster during a suspend/off request and so on.

Similarly, in the power up path this patch will allow an affinity instance at
level X to determine the state that an affinity instance at level X+1 has
emerged from, even after the level specific handlers have been called. This will
be useful in determining whether a CPU is the first in the cluster during a
on/resume request and so on.

As before, while powering down, state is updated before the level specific
handlers are invoked so that they can perform actions based upon their target
state. While powering up, state is updated after the level specific handlers have
been invoked so that they can perform actions based upon the state they emerged
from.

Change-Id: I40fe64cb61bb096c66f88f6d493a1931243cfd37

This patch uses stacks allocated in normal memory to enable the MMU early in the
warm boot path thus removing the dependency on stacks allocated in coherent
memory. Necessary cache and stack maintenance is performed when a cpu is being
powered down and up. This avoids any coherency issues that can arise from
reading speculatively fetched stale stack memory from another CPUs cache. These
changes affect the warm boot path in both BL3-1 and BL3-2.

The EL3 system registers responsible for preserving the MMU state are not saved
and restored any longer. Static values are used to program these system
registers when a cpu is powered on or resumed from suspend.

Change-Id: I8357e2eb5eb6c5f448492c5094b82b8927603784

This patch adds a 'flags' parameter to each exception level specific function
responsible for enabling the MMU. At present only a single flag which indicates
whether the data cache should also be enabled is implemented. Subsequent patches
will use this flag when enabling the MMU in the warm boot paths.

Change-Id: I0eafae1e678c9ecc604e680851093f1680e9cefa

Many of the interfaces internal to PSCI pass the current CPU
MPIDR_EL1 value from function to function. This is not required,
and with inline access to the system registers is less efficient
than requiring the code to read that register whenever required.

This patch remove the mpidr parameter from the affected interfaces
and reduces code in FVP BL3-1 size by 160 bytes.

Change-Id: I16120a7c6944de37232016d7e109976540775602

Consolidate all BL3-1 CPU context initialization for cold boot, PSCI
and SPDs into two functions:
*  The first uses entry_point_info to initialize the relevant
   cpu_context for first entry into a lower exception level on a CPU
*  The second populates the EL1 and EL2 system registers as needed
   from the cpu_context to ensure correct entry into the lower EL

This patch alters the way that BL3-1 determines which exception level
is used when first entering EL1 or EL2 during cold boot - this is now
fully determined by the SPSR value in the entry_point_info for BL3-3,
as set up by the platform code in BL2 (or otherwise provided to BL3-1).

In the situation that EL1 (or svc mode) is selected for a processor
that supports EL2, the context management code will now configure all
essential EL2 register state to ensure correct execution of EL1. This
allows the platform code to run non-secure EL1 payloads directly
without requiring a small EL2 stub or OS loader.

Change-Id: If9fbb2417e82d2226e47568203d5a369f39d3b0f

The crash reporting support and early initialisation of the
cpu_data allow the runtime_exception vectors to be used from
the start in BL3-1, removing the need for the additional
early_exception vectors and 2KB of code from BL3-1.

Change-Id: I5f8997dabbaafd8935a7455910b7db174a25d871

This patch prepares the per-cpu pointer cache for wider use by:
* renaming the structure to cpu_data and placing in new header
* providing accessors for this CPU, or other CPUs
* splitting the initialization of the TPIDR pointer from the
  initialization of the cpu_data content
* moving the crash stack initialization to a crash stack function
* setting the TPIDR pointer very early during boot

Change-Id: Icef9004ff88f8eb241d48c14be3158087d7e49a3

All callers of cm_get_context() pass the calling CPU MPIDR to the
function. Providing a specialised version for the current
CPU results in a reduction in code size and better readability.

The current function has been renamed to cm_get_context_by_mpidr()
and the existing name is now used for the current-CPU version.

The same treatment has been done to cm_set_context(), although
only both forms are used at present in the PSCI and TSPD code.

Change-Id: I91cb0c2f7bfcb950a045dbd9ff7595751c0c0ffb

Previously, the enable_mmu_elX() functions were implicitly part of
the platform porting layer since they were included by generic
code. These functions have been placed behind 2 new platform
functions, bl31_plat_enable_mmu() and bl32_plat_enable_mmu().
These are weakly defined so that they can be optionally overridden
by platform ports.

Also, the enable_mmu_elX() functions have been moved to
lib/aarch64/xlat_tables.c for optional re-use by platform ports.
These functions are tightly coupled with the translation table
initialization code.

Fixes ARM-software/tf-issues#152

Change-Id: I0a2251ce76acfa3c27541f832a9efaa49135cc1c

Previously, platform.h contained many declarations and definitions
used for different purposes. This file has been split so that:

* Platform definitions used by common code that must be defined
  by the platform are now in platform_def.h. The exact include
  path is exported through $PLAT_INCLUDES in the platform makefile.

* Platform definitions specific to the FVP platform are now in
  /plat/fvp/fvp_def.h.

* Platform API declarations specific to the FVP platform are now
  in /plat/fvp/fvp_private.h.

* The remaining platform API declarations that must be ported by
  each platform are still in platform.h but this file has been
  moved to /include/plat/common since this can be shared by all
  platforms.

Change-Id: Ieb3bb22fbab3ee8027413c6b39a783534aee474a

This patch implements the register reporting when unhandled exceptions are
taken in BL3-1. Unhandled exceptions will result in a dump of registers
to the console, before halting execution by that CPU. The Crash Stack,
previously called the Exception Stack, is used for this activity.
This stack is used to preserve the CPU context and runtime stack
contents for debugging and analysis.

This also introduces the per_cpu_ptr_cache, referenced by tpidr_el3,
to provide easy access to some of BL3-1 per-cpu data structures.
Initially, this is used to provide a pointer to the Crash stack.

panic() now prints the the error file and line number in Debug mode
and prints the PC value in release mode.

The Exception Stack is renamed to Crash Stack with this patch.
The original intention of exception stack is no longer valid
since we intend to support several valid exceptions like IRQ
and FIQ in the trusted firmware context. This stack is now
utilized for dumping and reporting the system state when a
crash happens and hence the rename.

Fixes ARM-software/tf-issues#79 Improve reporting of unhandled exception

Change-Id: I260791dc05536b78547412d147193cdccae7811a

Instead of having a single version of the MMU setup functions for all
bootloader images that can execute either in EL3 or in EL1, provide
separate functions for EL1 and EL3. Each bootloader image can then
call the appropriate version of these functions. The aim is to reduce
the amount of code compiled in each BL image by embedding only what's
needed (e.g. BL1 to embed only EL3 variants).

Change-Id: Ib86831d5450cf778ae78c9c1f7553fe91274c2fa

Reduce the number of header files included from other header
files as much as possible without splitting the files. Use forward
declarations where possible. This allows removal of some unnecessary
"#ifndef __ASSEMBLY__" statements.

Also, review the .c and .S files for which header files really need
including and reorder the #include statements alphabetically.

Fixes ARM-software/tf-issues#31

Change-Id: Iec92fb976334c77453e010b60bcf56f3be72bd3e

Add tag names to all unnamed structs in header files. This
allows forward declaration of structs, which is necessary to
reduce header file nesting (to be implemented in a subsequent
commit).

Also change the typedef names across the codebase to use the _t
suffix to be more conformant with the Linux coding style. The
coding style actually prefers us not to use typedefs at all but
this is considered a step too far for Trusted Firmware.

Also change the IO framework structs defintions to use typedef'd
structs to be consistent with the rest of the codebase.

Change-Id: I722b2c86fc0d92e4da3b15e5cab20373dd26786f

Move the BL function prototypes out of arch.h and into the
appropriate header files to allow more efficient header file
inclusion. Create new BL private header files where there is no
sensible existing header file.

Change-Id: I45f3e10b72b5d835254a6f25a5e47cf4cfb274c3

Make codebase consistent in its use of #include "" syntax for
user includes and #include <> syntax for system includes.

Fixes ARM-software/tf-issues#65

Change-Id: If2f7c4885173b1fd05ac2cde5f1c8a07000c7a33

This patch implements ARM Standard Service as a runtime service and adds
support for call count, UID and revision information SMCs. The existing
PSCI implementation is subsumed by the Standard Service calls and all
PSCI calls are therefore dispatched by the Standard Service to the PSCI
handler.

At present, PSCI is the only specification under Standard Service. Thus
call count returns the number of PSCI calls implemented. As this is the
initial implementation, a revision number of 0.1 is returned for call
revision.

Fixes ARM-software/tf-issues#62

Change-Id: I6d4273f72ad6502636efa0f872e288b191a64bc1