GitLab

Move up to Base FVP version 7.6

fiptool: Suppress verbose messages during normal build

gicv3: disable Group1 NonSecure interrupts during core powerdown

emmc: support CMD23

This patch updates the User Guide to move up from version 7.2 to 7.6
of the Base FVP.

Change-Id: I792b2250deb4836266e14b40992ae59a5ab5f729

The output is shown only when built with V=1.

Change-Id: I17fef10df6f127f07956a78b478ff3cadba4bd61

Support pwm for rk3399

Support CMD23. When CMD23 is used, CMD12 could be avoided.

Two scenarios:
1. CMD17 for single block, CMD18 + CMD12 for multiple blocks.
2. CMD23 + CMD18 for both single block and multiple blocks.

The emmc_init() should initialize whether CMD23 is supported
or not.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

As per the GICv3 specification, to power down a processor using GICv3
and allow automatic power-on if an interrupt must be sent to a processor,
software must set Enable to zero for all interrupt groups(by writing to
GICC_CTLR or ICC_IGRPEN{0,1}_EL1/3 as appropriate.

Also, NonSecure EL1 software may not be aware of the CPU power state
details and fail to choose right states that require quiescing the CPU
interface. So it's preferred that the PSCI implementation handles it as
it is fully aware of the CPU power states.

This patch adds disabling of Group1 NonSecure interrupts during processor
power down along with Group0 and Group1 Secure interrupts so that all the
interrupt groups are handled at once as per specification.

Change-Id: Ib564d773c9c4c41f2ca9471451c030e3de75e641

The pmusgrf reset-hold bits needs to be released, since the
pmusgrf reset-hold bits needs to be held.

Change-Id: Ia1eccc8fba18294f26b4cc07d47bc5e513dd9a1f

Sometimes this will cause the long delay for suspend/resume.
Since the 24M OCS will be turned off in power mode.
Also, remove the ERROR_DEPRECATED config define.

Change-Id: I78f21c35912c2250972e551695cdacc7bc4c020a

This patch updates some things for rk3399, as following:

1) Add the new file to handle the pwm. (e.g. the pwm regulator)
Make sure that good deal with the pwm related things.
Also, remove some pwm setting for pmu.c.

2) Set the plls slow mode and bypass in suspend, and restore them.

Change-Id: I112806700bf433c87763aac23d22fa7e6a7f5264

io: block: fix unaligned buffer

Replace fip_create with fiptool

If buffer address parameter isn't aligned, it may cause
DMA issue in block device driver, as eMMC. Now check the buffer
address. If it's not aligned, use temporary buffer in io block
driver instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

fiptool provides a more consistent and intuitive interface compared to
the fip_create program.  It serves as a better base to build on more
features in the future.

fiptool supports various subcommands.  Below are the currently
supported subcommands:

1) info   - List the images contained in a FIP file.
2) create - Create a new FIP file with the given images.
3) update - Update an existing FIP with the given images.
4) unpack - Extract a selected set or all the images from a FIP file.
5) remove - Remove images from a FIP file.  This is a new command that
   was not present in fip_create.

To create a new FIP file, replace "fip_create" with "fiptool create".

To update a FIP file, replace "fip_create" with "fiptool update".

To dump the contents of a FIP file, replace "fip_create --dump" with
"fiptool info".

A compatibility script that emulates the basic functionality of
fip_create is provided.  Existing scripts might or might not work with
the compatibility script.  Users are strongly encouraged to migrate to
fiptool.

Fixes ARM-Software/tf-issues#87
Fixes ARM-Software/tf-issues#108
Fixes ARM-Software/tf-issues#361

Change-Id: I7ee4da7ac60179cc83cf46af890fd8bc61a53330

Documentation for SEPARATE_CODE_AND_RODATA build flag

This patch documents the effect, cost and benefits of the
SEPARATE_CODE_AND_RODATA build flag.

Change-Id: Ic8daf0563fa6335930ad6c70b9c35f678e84d39d

rockchip: fixes typo and some bugs for suspend/resume tests

Improve debug assertion for runtime svc number

GICv3: Fix the GICD_IROUTER offset

ARM platforms: Define common image sizes

1. Remove the AP_PWROFF in ATF, should configure it in kernel.
2. Save and restore the PWMs pin/regs for suspend/resume.
3. The pmusgrf reset-hold bits needs to be released. since the
   pmusgrf reset-hold bits needs to be held.
4. Configure the PMU power up/down cycles about delay 3ms.
5. With the MMIO register block as one big mapping.
6. Fix the build error with psci_entrypoint since PSCI lib updated.

Fixes the commit
9ec78bdf ("rockchip: support the suspend/resume for rk3399").

Change-Id: I112806700bf433c87763aac23d22fa7e6a7f5264

This patch fixes the offset of GICD_IROUTER register defined in gicv3.h.
Although the GICv3 documention mentions that the offset for this register
is 0x6100-0x7FD8, the offset calculation for an interrupt id `n` is :

   0x6000 + 8n, where n >= 32

This requires the offset for GICD_IROUTER to be defined as 0x6000.

Fixes ARM-software/tf-issues#410

Change-Id: If9e91e30d946afe7f1f60fea4f065c7567093fa8

This patch improves the debug assertion for runtime svc number
 - Remove useless comparison ensuring that the number of descriptors
   is a positive number. The variable is an unsigned integer so can't
   be negative.
 - Check that the end address of the descriptors is sane relative
   to the start address.

Change-Id: Iea7be6b34e33b8b1cbd394eb923cc834ea964831

Fix use of stale power states in PSCI standby finisher

Minor improvements to harden TF code

A PSCI CPU_SUSPEND request to place a CPU in retention states at power levels
higher than the CPU power level is subject to the same state coordination as a
power down state. A CPU could implement multiple retention states at a
particular power level. When exiting WFI, the non-CPU power levels may be in a
different retention state to what was initially requested, therefore each CPU
should refresh its view of the states of all power levels.

Previously, a CPU re-used the state of the power levels when it entered the
retention state. This patch fixes this issue by ensuring that a CPU upon exit
from retention reads the state of each power level afresh.

Change-Id: I93b5f5065c63400c6fd2598dbaafac385748f989

This patch adds some runtime checks to prevent some potential
pointer overflow issues in the is_mem_free() function. The overflow
could happen in the case where the end addresses, computed as the
sum of a base address and a size, results in a value large enough
to wrap around. This, in turn, could lead to unpredictable behaviour.

If such an overflow is detected, the is_mem_free() function will now
declare the memory region as not free. The overflow is detected using
a new macro, called check_uptr_overflow().

This patch also modifies all other places in the 'bl_common.c' file
where an end address was computed as the sum of a base address and a
size and instead keeps the two values separate. This avoids the need
to handle pointer overflows everywhere. The code doesn't actually need
to compute any end address before the is_mem_free() function is called
other than to print information message to the serial output.

This patch also introduces 2 slight changes to the reserve_mem()
function:

 - It fixes the end addresses passed to choose_mem_pos(). It was
   incorrectly passing (base + size) instead of (base + size - 1).

 - When the requested allocation size is 0, the function now exits
   straight away and says so using a warning message.
   Previously, it used to actually reserve some memory. A zero-byte
   allocation was not considered as a special case so the function
   was using the same top/bottom allocation mechanism as for any
   other allocation. As a result, the smallest area of memory starting
   from the requested base address within the free region was
   reserved.

Change-Id: I0e695f961e24e56ffe000718014e0496dc6e1ec6

 - Added some debug assertions checking that the runtime services
   indexes computed by get_unique_oen() are sane.

 - Do not print the name of the service when its descriptor is
   invalid. If the descriptor is corrupted then its name field
   could be corrupted as well and we would end up reading an
   arbitrary amount of invalid memory.

Change-Id: I16f61065277d01fe1555d5a9cf743f7b52ccaa60

Light refactoring of the code in runtime_svc.c file.

 - Declare validate_rt_svc_desc()'s argument as const.

 - Remove 'goto' path in runtime_svc_init(). It was used in one
   place only.

 - Improve code readability by declaring a local variable holding the
   service pointer.

Change-Id: I3b15c5adb9f37b786b5b993a9be70ea9dd017a83

This patch adds a runtime check that psci_find_target_suspend_lvl()
returns a valid value back to psci_cpu_suspend() and psci_get_stat().
If it is invalid, BL31 will now panic.

Note that on the PSCI CPU suspend path there is already a debug
assertion checking the validity of the target composite power state,
which effectively also checks the validity of the target suspend level.
Therefore, the error condition would already be caught in debug builds,
but in a release build this assertion would be compiled out.

On the PSCI stat path, there is currently no debug assertion checking
the validity of the power state before using it as an index into
the power domain state array.

Although BL31 platforms ports are responsible for validating the
power state parameter, the security impact (i.e. an out-of-bounds
array access) of a potential platform port bug in this code would
be quite high, given that this parameter comes from an untrusted
source. The cost of checking this in runtime generic code is low.

Change-Id: Icea85b8020e39928ac03ec0cd49805b5857b3906

Introduce PSCI library

Compile option `ARM_BOARD_OPTIMISE_MMAP` has been renamed to
`ARM_BOARD_OPTIMISE_MEM` because it now applies not only to defines
related to the translation tables but to the image size as well.

The defines `PLAT_ARM_MAX_BL1_RW_SIZE`, `PLAT_ARM_MAX_BL2_SIZE` and
`PLAT_ARM_MAX_BL31_SIZE` have been moved to the file board_arm_def.h.
This way, ARM platforms no longer have to set their own values if
`ARM_BOARD_OPTIMISE_MEM=0` and they can specify optimized values
otherwise. The common sizes have been set to the highest values used
for any of the current build configurations.

This is needed because in some build configurations some images are
running out of space. This way there is a common set of values known
to work for all of them and it can be optimized for each particular
platform if needed.

The space reserved for BL2 when `TRUSTED_BOARD_BOOT=0` has been
increased. This is needed because when memory optimisations are
disabled the values for Juno of `PLAT_ARM_MMAP_ENTRIES` and
`MAX_XLAT_TABLES` are higher. If in this situation the code is
compiled in debug mode and with "-O0", the code won't fit.

Change-Id: I70a3d8d3a0b0cad1d6b602c01a7ea334776e718e

This patch moves assembler macros which are not architecture specific
to a new file `asm_macros_common.S` and moves the `el3_common_macros.S`
into `aarch64` specific folder.

Change-Id: I444a1ee3346597bf26a8b827480cd9640b38c826

Previously the definition of `plat_get_syscnt_freq2()` in `arm_common.c` was
conditionally defined based on the ERROR_DEPRECATED flag. This patch makes
this function available irrespective of the flag and removes the deprecated
`plat_get_syscnt_freq()` definition.

Change-Id: I250ca787ca1b5e867096c6ba8f2bb444db44c97b

The PRELOADED_BL33_BASE build option allows to preload a BL33 and bypass its
loading by BL2. In ARM standard platforms, the conditional behaviour of
PRELOADED_BL33_BASE is moved within the implementation of
`plat_get_ns_image_entrypoint()` so that all callers may benefit from this
feature.

Change-Id: Iea060e204ec72f8081087837854535c4e320da4e

This patch moves the `arm_common.c` file from `plat/arm/common/aarch64/`
to the parent directory since the functions implemented in the file are
not AArch64 specific. The platform makefiles are also modified for this
change.

Change-Id: I776d2e4958f59041476cf2f53a9adb5b2d304ee0

The `plat_psci_common.c` was moved to the new location `plat/common`
and a stub file was retained at previous location for compatibility. This
patch modifies the platform makefiles to include the file from the new
location.

Change-Id: Iabddeeb824e9a5d72d176d7c644735966c8c0699

This patch introduces the PSCI Library interface. The major changes
introduced are as follows:

* Earlier BL31 was responsible for Architectural initialization during cold
boot via bl31_arch_setup() whereas PSCI was responsible for the same during
warm boot. This functionality is now consolidated by the PSCI library
and it does Architectural initialization via psci_arch_setup() during both
cold and warm boots.

* Earlier the warm boot entry point was always `psci_entrypoint()`. This was
not flexible enough as a library interface. Now PSCI expects the runtime
firmware to provide the entry point via `psci_setup()`. A new function
`bl31_warm_entrypoint` is introduced in BL31 and the previous
`psci_entrypoint()` is deprecated.

* The `smc_helpers.h` is reorganized to separate the SMC Calling Convention
defines from the Trusted Firmware SMC helpers. The former is now in a new
header file `smcc.h` and the SMC helpers are moved to Architecture specific
header.

* The CPU context is used by PSCI for context initialization and
restoration after power down (PSCI Context). It is also used by BL31 for SMC
handling and context management during Normal-Secure world switch (SMC
Context). The `psci_smc_handler()` interface is redefined to not use SMC
helper macros thus enabling to decouple the PSCI context from EL3 runtime
firmware SMC context. This enables PSCI to be integrated with other runtime
firmware using a different SMC context.

NOTE: With this patch the architectural setup done in `bl31_arch_setup()`
is done as part of `psci_setup()` and hence `bl31_platform_setup()` will be
invoked prior to architectural setup. It is highly unlikely that the platform
setup will depend on architectural setup and cause any failure. Please be
be aware of this change in sequence.

Change-Id: I7f497a08d33be234bbb822c28146250cb20dab73