GitLab

Add support to retrieve plat_toc_flags value from FIP header flags.
plat_toc_flags is for platform specific use. It is stored in
FIP header by fiptool using --plat-toc-flags option.

Change-Id: Ibadd91b4f28e6503f4426e4efd404bbe512ad124
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>

TBBR spec advocates for optional encryption of firmwares (see optional
requirement: R060_TBBR_FUNCTION). So add an IO abstaction layer to
support firmware decryption that can be stacked above any underlying IO/
packaging layer like FIP etc. It aims to provide a framework to load any
encrypted IO payload.

Also, add plat_get_enc_key_info() to be implemented in a platform
specific manner as handling of encryption key may vary from one platform
to another.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Change-Id: I9892e0ddf00ebecb8981301dbfa41ea23e078b03

The raw NAND framework supports SLC NAND devices.

It introduces a new high level interface (io_mtd) that
defines operations a driver can register to the NAND framework.
This interface will fill in the io_mtd device specification:
	- device_size
        - erase_size
that could be used by the io_storage interface.

NAND core source file integrates the standard read loop that
performs NAND device read operations using a skip bad block strategy.
A platform buffer must be defined in case of unaligned
data. This buffer must fit to the maximum device page size
defined by PLATFORM_MTD_MAX_PAGE_SIZE.

The raw_nand.c source file embeds the specific NAND operations
to read data.
The read command is a raw page read without any ECC correction.
This can be overridden by a low level driver.
No generic support for write or erase command or software
ECC correction.

NAND ONFI detection is available and can be enabled using
NAND_ONFI_DETECT=1.
For non-ONFI NAND management, platform can define required
information.

Change-Id: Id80e9864456cf47f02b74938cf25d99261da8e82
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

IO seek offset can be set to values above UINT32_MAX, this change
changes the seek offset argument from 'ssize_t' to 'signed long long'.
Fixing platform seek functions to match the new interface update.

Change-Id: I25de83b3b7abe5f52a7b0fee36f71e60cac9cfcb
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Improved support for W=1 compilation flag by solving missing-prototypes
and old-style-definition warnings.

The libraries are compiling with warnings (which turn into errors with
the Werror flag).

Outside of libraries, some warnings cannot be fixed without heavy
structural changes.

Change-Id: I1668cf99123ac4195c2a6a1d48945f7a64c67f16
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

The comment suggests checking version numbers and
a checksum but there doesn't seem to be any usable
data for either of these.

For example, fip_toc_header_t doesn't contain any
version information and neither does fip_toc_entry_t.

As the function name "is_valid_header" suggests, this
function is not concerned with checksumming any of
the table of contents entries.

Change-Id: I8673ae5dd37793771760169f26b2f55c15fbf587
Signed-off-by: Paul Beesley <paul.beesley@arm.com>

This TODO was added five years ago so I assume that there is not
going to be a shutdown API added after all.

Change-Id: If0f4e2066454df773bd9bf41ed65d3a10248a2d3
Signed-off-by: Paul Beesley <paul.beesley@arm.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This is used as a table index, and already compared with an unsigned int:
block_dev_count.
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Remove assert on buffer address equal zero.
Marvell uses address 0x0 for loading BL33,
so this check is irrelevant and breaks the
debug builds on Marvell platforms.

Change-Id: Ie56a51138e2e4ddd8986dd7036797dc2d8b10125
Signed-off-by: Haim Boot <hayim@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/54589

Platform can define MAX_NUM_FIP_DEVICES in platform_def.h
to define the number of FIP io devices.

The FIP driver doesn't support muliple open file.
So only one single file can be open at a time across
multiple FIP devices.

For any FIP device, an image should be loaded
fully before moving on to the next image.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>

RFC4122 defines that fields are stored in network order (big endian),
but TF-A stores them in machine order (little endian by default in TF-A).
We cannot change the future UUIDs that are already generated, but we can store
all the bytes using arrays and modify fiptool to generate the UUIDs with
the correct byte order.

Change-Id: I97be2d3168d91f4dee7ccfafc533ea55ff33e46f
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined.

Change-Id: I26e042cb251a6f9590afa1340fdac73e42f23979
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This fixes all defects according to MISRA Rule 3.1: "The character
sequences /* and // shall not be used within a comment". This affects
all URLs in comments, so they have been removed:

- The link in `sdei_state.c` can also be found in the documentation file
  `docs/sdei.rst`.

- The bug that the file `io_fip.c` talks about doesn't affect the
  currently supported version of GCC, so it doesn't make sense to keep
  the comment. Note that the version of GCC officially supported is the
  one that comes with Linaro Release 17.10, which is GCC 6.2.

- The link in `tzc400.c` was broken, and it didn't correctly direct to
  the Technical Reference Manual it should. The link has been replaced
  by the title of the document, which is more convenient when looking
  for the document.

Change-Id: I89f60c25f635fd4c008a5d3a14028f814c147bbe
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The block operations were trying to optimize the number of memory
copies, and it tried to use directly the buffer supplied by the user
to them. This was a mistake because it created too many corner cases:

	1- It was possible to generate unaligned
	   operations to unaligned buffers. Drivers that were using
	   DMA transfer failed in that case.

	2- It was possible to generate read operations
	   with sizes that weren't a multiple of the block size. Some
	   low level drivers assumed that condition and they calculated
	   the number of blocks dividing the number of bytes by the
	   size of the block, without considering the remaining bytes.

	3- The block_* operations didn't control the
	   number of bytes actually copied to memory, because the
	   low level drivers were writing directly to the user buffer.

This patch rewrite block_read and block_write to use always the device
buffer, which the platform ensures that has the correct aligment and
the correct size.

Change-Id: I5e479bb7bc137e6ec205a8573eb250acd5f40420
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Include io_dummy.h header file.
Use static for device_type_dummy function.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

This change avoids warning about type conversion.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Many asserts depend on code that is conditionally compiled based on the
DEBUG define. This patch modifies the conditional inclusion of such code
so that it is based on the ENABLE_ASSERTIONS build option.

Change-Id: I6406674788aa7e1ad7c23d86ce94482ad3c382bd
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Static checks flag an assert added in commit 1f786b0f

 that compares
unsigned value to 0, which will never fail.

Change-Id: I4b02031c2cfbd9a25255d12156919dda7d4805a0
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

cppcheck highlighted variables that were initialized but then later
reassigned.

Change-Id: Ie12742c01fd3bf48b2d6c05a3b448da91d57a2e4
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

The memmap IO driver doesn't perform bounds check when reading, writing,
or seeking. The onus to vet parameters is on the caller, and this patch
asserts that:

  - non-negative size is specified for for backing memory;

  - valid parameters are passed into the driver for read, write and seek
    operations.

Change-Id: I6518c4065817e640e9e7e39a8a4577655f2680f7
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Replace all use of memset by zeromem when zeroing moderately-sized
structure by applying the following transformation:
memset(x, 0, sizeof(x)) => zeromem(x, sizeof(x))

As the Trusted Firmware is compiled with -ffreestanding, it forbids the
compiler from using __builtin_memset and forces it to generate calls to
the slow memset implementation. Zeromem is a near drop in replacement
for this use case, with a more efficient implementation on both AArch32
and AArch64.

Change-Id: Ia7f3a90e888b96d056881be09f0b4d65b41aa79e
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

If buffer address parameter isn't aligned, it may cause
DMA issue in block device driver, as eMMC. Now check the buffer
address. If it's not aligned, use temporary buffer in io block
driver instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Allow to handle cases where some images are pre-loaded (by debugger for
instance) without introducing many switches in files calling load_* functions.

Fixes: arm-software/tf-issues#398
Signed-off-by: Gerald Lejeune <gerald.lejeune@st.com>

FIP is accessed as memory-mapped type. eMMC is block device type.
In order to support FIP based on eMMC, add the new io_block layer.

io_block always access eMMC device as block size. And it'll only
copy the required data into buffer in io_block driver. So preparing
an temporary buffer is required.

When use io_block device, MAX_IO_BLOCK_DEVICES should be declared
in platform_def.h. It's used to support multiple block devices.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Hence memmap device can be used to load an image without being wrapped in a
FIP.

Fixes arm-software/tf-issues#371
Signed-off-by: Gerald Lejeune <gerald.lejeune@st.com>

Migrate all direct usage of __attribute__ to usage of their
corresponding macros from cdefs.h.
e.g.:
 - __attribute__((unused)) -> __unused
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Patch 7e26fe1f deprecates IO specific return definitions in favour
of standard errno codes. This patch removes those definitions
and its usage from the IO framework, IO drivers and IO platform
layer. Following this patch, standard errno codes must be used
when checking the return value of an IO function.

Change-Id: Id6e0e9d0a7daf15a81ec598cf74de83d5768650f

The return value from the SYS_WRITE semihosting operation is 0 if
the call is successful or the number of bytes not written, if there
is an error. The implementation of the write function in the
semihosting driver treats the return value as the number of bytes
written, which is wrong. This patch fixes it.

Change-Id: Id39dac3d17b5eac557408b8995abe90924c85b85

The Trusted firmware code identifies BL images by name. The platform
port defines a name for each image e.g. the IO framework uses this
mechanism in the platform function plat_get_image_source(). For
a given image name, it returns the handle to the image file which
involves comparing images names. In addition, if the image is
packaged in a FIP, a name comparison is required to find the UUID
for the image. This method is not optimal.

This patch changes the interface between the generic and platform
code with regard to identifying images. The platform port must now
allocate a unique number (ID) for every image. The generic code will
use the image ID instead of the name to access its attributes.

As a result, the plat_get_image_source() function now takes an image
ID as an input parameter. The organisation of data structures within
the IO framework has been rationalised to use an image ID as an index
into an array which contains attributes of the image such as UUID and
name. This prevents the name comparisons.

A new type 'io_uuid_spec_t' has been introduced in the IO framework
to specify images identified by UUID (i.e. when the image is contained
in a FIP file). There is no longer need to maintain a look-up table
[iname_name --> uuid] in the io_fip driver code.

Because image names are no longer mandatory in the platform port, the
debug messages in the generic code will show the image identifier
instead of the file name. The platforms that support semihosting to
load images (i.e. FVP) must provide the file names as definitions
private to the platform.

The ARM platform ports and documentation have been updated accordingly.
All ARM platforms reuse the image IDs defined in the platform common
code. These IDs will be used to access other attributes of an image in
subsequent patches.

IMPORTANT: applying this patch breaks compatibility for platforms that
use TF BL1 or BL2 images or the image loading code. The platform port
must be updated to match the new interface.

Change-Id: I9c1b04cb1a0684c6ee65dee66146dd6731751ea5

This patch defines the ARRAY_SIZE macro for calculating number of elements
in an array and uses it where appropriate.

Change-Id: I72746a9229f0b259323972b498b9a3999731bc9b

This patch adds support to authenticate the Trusted Key certificate
and the BL3-x certificates and images at BL2.

Change-Id: I69a8c13a14c8da8b75f93097d3a4576aed71c5dd

This patch adds support to authenticate the BL2 content certificate
and image using the authentication module in BL1.

The FIP driver has been extended to include the BL2 certificate
UUID.

FVP and Juno ports include the BL2 certificate FIP file
definition.

Change-Id: I32680e9bd123c8db4a4193c14448c9b32b0e9325

Move the remaining IO storage source file (io_storage.c) from the
lib to the drivers directory. This requires that platform ports
explicitly add this file to the list of source files.

Also move the IO header files to a new sub-directory, include/io.

Change-Id: I862b1252a796b3bcac0d93e50b11e7fb2ded93d6

Fix the following issues with the console log output:

* Make sure the welcome string is the first thing in the log output
(during normal boot).
* Prefix each message with the BL image name so it's clear which
BL the output is coming from.
* Ensure all output is wrapped in one of the log output macros so it can
be easily compiled out if necessary. Change some of the INFO() messages
to VERBOSE(), especially in the TSP.
* Create some extra NOTICE() and INFO() messages during cold boot.
* Remove all usage of \r in log output.

Fixes ARM-software/tf-issues#231

Change-Id: Ib24f7acb36ce64bbba549f204b9cde2dbb46c8a3

 - Add support for loading a BL3-0 image in BL2. Information about
   memory extents is populated by platform-specific code. Subsequent
   handling of BL3-0 is also platform specific.
   The BL2 main function has been broken down to improve readability.
   The BL3-2 image is now loaded before the BL3-3 image to align with
   the boot flow.

 - Build system: Add support for specifying a BL3-0 image that will be
   included into the FIP image.

 - IO FIP driver: Add support for identifying a BL3-0 image inside a
   FIP image.

 - Update the documentation to reflect the above changes.

Change-Id: I067c184afd52ccaa86569f13664757570c86fc48

Previously, platform.h contained many declarations and definitions
used for different purposes. This file has been split so that:

* Platform definitions used by common code that must be defined
  by the platform are now in platform_def.h. The exact include
  path is exported through $PLAT_INCLUDES in the platform makefile.

* Platform definitions specific to the FVP platform are now in
  /plat/fvp/fvp_def.h.

* Platform API declarations specific to the FVP platform are now
  in /plat/fvp/fvp_private.h.

* The remaining platform API declarations that must be ported by
  each platform are still in platform.h but this file has been
  moved to /include/plat/common since this can be shared by all
  platforms.

Change-Id: Ieb3bb22fbab3ee8027413c6b39a783534aee474a

The generic image loading and IO FIP code no longer forces the
platform to create BL3-2 (Secure-EL1 Payload) specific
definitions. The BL3-2 loading code in bl2/bl2main.c is wrapped
by a #ifdef BL32_BASE blocks, allowing the BL3-2 definitions to
be optional. Similarly for the name_uuid array defintion in
drivers/io/io_fip.c.

Also update the porting guide to reflect this change.

The BL3-2 platform definitions remain non-configurably present
in the FVP port.

Fixes ARM-software/tf-issues#68

Change-Id: Iea28b4e94d87a31f5522f271e290919a8a955460

Update code base to remove variables from the .data section,
mainly by using const static data where possible and adding
the const specifier as required. Most changes are to the IO
subsystem, including the framework APIs. The FVP power
management code is also affected.

Delay initialization of the global static variable,
next_image_type in bl31_main.c, until it is realy needed.
Doing this moves the variable from the .data to the .bss
section.

Also review the IO interface for inconsistencies, using
uintptr_t where possible instead of void *. Remove the
io_handle and io_dev_handle typedefs, which were
unnecessary, replacing instances with uintptr_t.

Fixes ARM-software/tf-issues#107.

Change-Id: I085a62197c82410b566e4698e5590063563ed304