GitLab

Do not power off the CPU1 since there is no way to wake it up
(wake-up is causing CPU0 reset as well duo to HW bug). Quote from errata
Ref #13 [In power saving mode, both cores must be powered off]:
"When Core 0 is on and Core 1 is in power-off state, a Core 1
wake-up resets Core 0 as well and puts Core 0 back to ROM".

To overcome described HW bug instead of powering the CPU off, let it
reach WFI instruction, which is invoked by generic psci_do_cpu_off
function after platform handler finishes. This will put the core in low
power state and give a chance to wake it up.

Before this change, after running secondary kernel via kexec, only one
core was up, now both cores are up.

Change-Id: I87f144867550728055d9b8a2edb84a14539acab7
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

The headers forked at some point in the past and have diverged a lot. In
order to make it easier to share code between TF-A-Tests and TF-A, this
patch synchronises most of the definitions in the mentioned headers.

This is not a complete sync, it has to be followed by more cleanup.

This patch also removes the read helpers for the AArch32 instructions
ats1cpr and ats1hr (they are write-only).

Change-Id: Id13ecd7aeb83bd2318cd47156d71a42f1c9f6ba2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch adds support to build a combined BL1
and ROMLIB binary file with the right page
alignment in Juno. When USE_ROMLIB=1 is set for
Juno, it generates the combined file
bl1_romlib.bin which needs to be used instead of
bl1.bin

Change-Id: I407efbe48d3e522fa6ef855538a9587193cb1919
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

Remove the platform common plat_arm_security_setup function to allow
platform specific implementations of the security setup function
implemented in the board directory of the platform.

For use by secure software, configure region0 of DMC-620 trustzone
controller to protect the upper 16MB of memory of the first DRAM block
from non-secure accesses.

Change-Id: I9a8c19656702c4fa4f6917b3655b692d443bb568
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

RCAR_RPC_HYPERFLASH_LOCKED can be set to 0 as a build option if the
user needs to allow u-boot to reprogram the ATF firmware using a FIP
image (as a faster alternative of toggling numerous DIP switches on
the board and using ascii-xfer of srec files)

The code being controlled with this commit should only be re-enabled for
debugging (_never_ on a product release)
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>

The default Raspberry Pi 3 memory mapping for ATF is geared towards
the use of uboot + Linux. This creates issues when trying to use
ATF with an UEFI payload and Windows on ARM64.

We therefore introduce new build option RPI3_USE_UEFI_MAP, that
enables the build process to use an alternate memory mapping that
is compatible with UEFI + Windows (as well as UEFI + Linux).

Fixes ARM-software/tf-issues#649
Signed-off-by: Pete Batard <pete@akeo.ie>

Some eMMC chips require a longer delay. After testing
different chips, 20ms appears to work reliably.
Signed-off-by: Ryan Grachek <ryan@edited.us>

Migrate Marvell platforms from legacy console API to
multi-console API.

Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Signed-off-by: Yann Gautier <yann.gautier@st.com>

According to "openssl" manual:
-K key
The actual key to use: this must be represented as a string
comprised only of hex digits. If only the key is specified,
the IV must additionally specified using the -iv option.
When both a key and a password are specified, the key given
with the -K option will be used and the IV generated from the
password will be taken.
It does not make much sense to specify both key and password.

This patch removes "-k 0" parameter from the encryption command
since we are already using "-K" and "-iv" for the key and IV.

Change-Id: Ia333cedaa3207e643c95d2ec7c229f50eeab96db
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/60745

Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Sharon Habet <sharonh@marvell.com>

The DCDC6 power rail is typically driving VDD_SYS in the SoC, so it is
on by default and uses the default voltage.

As there seems to be at least on board using a different voltage, add
the rail to the list of known voltage lines, so we can setup the right
voltage as early as possible.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The DCDC1 and DCDC5 power rails didn't specify the enable bits. This
isn't critical, since those rails are on by default (and are needed for
every board), but it is inconsistent.

Add the respective enable bits for those two rails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The DRIVEVBUS pin setup was broken in two ways:
- To configure this pin as an output pin, one has to *clear* the bit in
  register 0x8f. It is 0 by default, but rebooting from Linux might have
  left this bit set.
- Doing this just configures the pin as an output pin, but doesn't
  actually drive power to it. This is done via bit 2 in register 0x30.

Fix the routine to both properly configure the pin and drive power to
it. Add an axp_clrsetbits() helper on the way.

Now this isn't really perfect, still:
We only need to setup the PMIC power rails that are needed for U-Boot.
DRIVEVBUS typically controls the VBUS voltage for the host function of
an USB-OTG port, something we typically don't want in U-Boot (fastboot,
using the USB *device* functionality, is much more common). The
BananaPi-M64 uses the regulator in this way, but the Remix Mini PC
actually controls the power of both its USB ports via this line.

Technically we should differentiate here: if DRIVEVBUS controls a
microUSB-B socket, the power should stay off, any host-type A sockets
should be supplied, though.
For now just always enable the power, that shouldn't really hurt the
USB-OTG functionality anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The legacy Allwinner ATF port used to setup some clocks, and U-Boot is
still relying on this. We don't need to setup the full set, as the SPL
is doing most of it, but it misses one clock (AHB2) and programs another
(AHB1) to quite conservative values.

Fix this up during the platform setup to improve USB and Ethernet
performance, iperf values go up by 31% in my setup with that patch.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Register a priority level, PLAT_SP_PRI, for secure partition with EL3
exception handling framework(ehf) module.

The secure partition manager(SPM) would raise the core's priority to
PLAT_SP_PRI before entering the secure partition, to protect the core
from getting interrupted while in secure partition.

Change-Id: I686897f052a4371e0efa9b929c07d3ad77249e95
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

Some OSes (e.g. Ubuntu 18.04 LTS on Raspberry Pi 3) may disable the
runtime UART in a manner that prevents the system from rebooting if
ATF tries to send runtime messages there.

Also, we don't want the firmware to share the UART with normal
world, as this can be a DoS attack vector into the secure world.

This patch fixes these 2 issues by introducing new build option
RPI3_RUNTIME_UART, that disables the runtime UART by default.

Fixes ARM-software/tf-issues#647
Signed-off-by: Pete Batard <pete@akeo.ie>

These issues wer found by sparse:

drivers/st/clk/stm32mp1_clk.c:1524:19:
 warning: incorrect type in assignment (different base types)
    expected restricted fdt32_t const [usertype] *pkcs_cell
    got unsigned int const [usertype] *

plat/st/stm32mp1/plat_image_load.c:13:6:
 warning: symbol 'plat_flush_next_bl_params' was not declared.
 Should it be static?
plat/st/stm32mp1/plat_image_load.c:21:16:
 warning: symbol 'plat_get_bl_image_load_info' was not declared.
 Should it be static?
plat/st/stm32mp1/plat_image_load.c:29:13:
 warning: symbol 'plat_get_next_bl_params' was not declared.
 Should it be static?

plat/st/stm32mp1/bl2_io_storage.c:40:10:
 warning: symbol 'block_buffer' was not declared. Should it be static?
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine Scalar
Processing Engines, Adaptable Hardware Engines, and Intelligent Engines with
leading-edge memory and interfacing technologies to deliver powerful
heterogeneous acceleration for any application. The Versal AI Core series has
five devices, offering 128 to 400 AI Engines. The series includes dual-core Arm
Cortex-A72 application processors, dual-core Arm Cortex-R5 real-time
processors, 256KB of on-chip memory with ECC, more than 1,900 DSP engines
optimized for high-precision floating point with low latency.

This patch adds Virtual QEMU platform support for
this SoC "versal_virt".
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.
Enables building with ERROR_DEPRECATED=1.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.
Enables building with ERROR_DEPRECATED=1.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.
Enables building with ERROR_DEPRECATED=1.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I2419416fadfcdf64da8b7690a348007591c4edf3
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Target builds but has not been tested.
Signed-off-by: ldts <jorge.ramirez.ortiz@gmail.com>

Signed-off-by: ldts <jorge.ramirez.ortiz@gmail.com>

This option allows the Trusted Firmware to directly jump to Linux
kernel for aarch32 without the need of an intermediate loader such
as U-Boot.

Similar to AArch64 ARM_LINUX_KERNEL_AS_BL33 only available with
RESET_TO_SP_MIN=1 as well as BL33 and DTB are preloaded in memory.

Change-Id: I908bc1633696be1caad0ce2f099c34215c8e0633
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

When CSS_USE_SCMI_DRIVER is not defined or set to 0, we get the
following build error.

plat/arm/board/juno/juno_topology.c:16:19: error: ‘CSS_SCMI_PAYLOAD_BASE’ undeclared here (not in a function)
   .scmi_mbx_mem = CSS_SCMI_PAYLOAD_BASE,
                   ^~~~~~~~~~~~~~~~~~~~~
plat/arm/board/juno/juno_topology.c:17:38: error: ‘CSS_SCMI_MHU_DB_REG_OFF’ undeclared here (not in a function)
   .db_reg_addr = PLAT_CSS_MHU_BASE + CSS_SCMI_MHU_DB_REG_OFF,
                                      ^~~~~~~~~~~~~~~~~~~~~~~
                                      CSS_CPU_PWR_STATE_OFF

Fix the error in order to get function legacy SCPI support functional.

Change-Id: I00cb80db9968aa0be546e33a3a682a2db87719be
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Change-Id: Iae6758ca6395560131d1e1a69a1ecfe50ca8bf83
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I33eaee8e7c983b3042635a448cb8d689ea4e3a12
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The macro EL_IMPLEMENTED() has been deprecated in favour of the new
function el_implemented().

Change-Id: Ic9b1b81480b5e019b50a050e8c1a199991bf0ca9
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Add supprot for Marvell platforms based on Armada-37xx SoC.
This includes support for the official Armada-3720 modular
development board and EspressoBin community board.
The Armada-37xx SoC contains dual Cortex-A53 Application CPU,
single secure CPU (Cortex-M3) and the following interfaces:
- SATA 3.0
- USB 3.0 and USB 2.0
- PCIe
- SDIO (supports boot from eMMC)
- SPI
- UART
- I2c
- Gigabit Ethernet
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

It boots failure on CircuitCo HiKey board. The delay could fix the
hang issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

A recent patch[0] has made setting up page tables into generic
code, complete the conversion for TI platforms by removing the
use of plat_arm_get_mmap() and using the mmap table directly.

[0] 0916c38d

 ("Convert arm_setup_page_tables into a generic helper")
Signed-off-by: Andrew F. Davis <afd@ti.com>

include/plat/arm/common isn't needed by them, and is removed to avoid
dependency on Arm platform code.

Change-Id: Id9fccba33326fd075b3d1029bf1e4b012dfa0483
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm files should only be used by Arm platforms. If other platforms
use them, they create dependencies that can introduce problems when
updating Arm platforms.

This patch copies the needed code from Arm platforms so that poplar can
be independent from them.

Change-Id: I0b194f5bdb0377b8ccacbd400e021614c026c7fe
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

When the SoC issues a command IRQ to SCP, SCP sets STMTOBEIRQ as ACK.
The SoC must wait for it before issuing the next command.

This commit makes sure to meet the requirement.
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Skipping SCP_BL2 image is just a temporary workaround. If on-chip SCP
needs to work, BL2 should load the SCP_BL2 image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

No functional changes.

Change-Id: I9b9f8d3dfde08d57706ad5450de6ff858a55ac01
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch adds support for the N1SDP (NeoVerse N1 System Development
Platform). It is an initial port and additional features are expected
to be added later.

The port includes only BL31 support as the System Control Processor
(SCP) is expected to take the role of primary boatloader

Change-Id: Ife17d8215a7bfcc1420204a72205e7ef920d0c10
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>

This patch enabled PIE for FVP when RESET_TO_BL31=1. The references
to BL31_BASE are replaced by BL31_START as being a symbol exported by
the linker, will create a dynamic relocation entry in .rela.dyn and
hence will be fixed up by dynamic linker at runtime. Also, we disable
RECLAIM_INIT_CODE when PIE is enabled as the init section overlay
creates some static relocations which cannot be handled by the
dynamic linker currently.

Change-Id: I86df1b0a8b2a8bbbe7c3f3c0b9a08c86c2963ec0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>