GitLab

Sync the platform code version with current Marvell LSP.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Very rarely, during cpuidle operations the following error
is seen: "PM MSG Trigger Timeout".
This is caused by slow handling of message interrutps
in the PM FW running on CM3 (under heavy PM operation load).

This is not a real issue, so we extend the timeout to
avoid the error prints.

Change-Id: I92fd6f2ff1ddf208b216c123880ded28a00b6e0e
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/59670

Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>

Add static configuration for SFI+ 10Gbps interface on SERDES
Lane 4.
This is just a copy of Lane 2 static values, not optimized.
Board-to-board iperf test shows up to 6Gbps transfer speed.

Change-Id: I024d2ac132f7fa6c342a64367f3dca2123a27e97
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>

- Number of open power switches for CPUs should be three
  and now two.

- This patch updates the value of open power switches from
  0xfd (two power-switches) to 0xfc (three power-switches).

Change-Id: I2783ab7f04bbbb6da78eeedcabe4636f9a774512
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Add support for SVC test builds for tuning AVS values.
Update the SVC procedure and add EEPROM access.
Add support for AP807 AVS values (10 bits wide).
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

- Update CPU frequency on AP807 to 2GHz for SAR 0x0.
- Increase AVS to 0.88V for 2GHz clock

Change-Id: Ic945b682ab2f8543e34294bfc56c3eae2c5e0c8e
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

In Armada 8K DB boards, PCIe initialization can be executed only once
because PCIe reset performed during chip power on and it cannot be
executed via GPIO later.
This means that power on can be executed only once, when it's called
from the bootloader.
Power on:
	Read bit 21 of the mode, it marks if the caller is
	the bootloader or the Linux Kernel.
Power off:
	Check if the comphy was already configured to PCIe, if yes,
	check if the caller is bootloader, if both conditions are true
	(PCIe mode and called by Linux) - skip the power-off.

In addition, fix incorrect documentation describing mode fields -
PCIe width is 3 bits, not 2.

NOTE: with this patch, please use LK4.14.76 (LK4.4.120 may not work
with it).

Change-Id: I4b929011f97a0a1869a51ba378687e78b3eca4ff
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Do not power off the CPU1 since there is no way to wake it up
(wake-up is causing CPU0 reset as well duo to HW bug). Quote from errata
Ref #13 [In power saving mode, both cores must be powered off]:
"When Core 0 is on and Core 1 is in power-off state, a Core 1
wake-up resets Core 0 as well and puts Core 0 back to ROM".

To overcome described HW bug instead of powering the CPU off, let it
reach WFI instruction, which is invoked by generic psci_do_cpu_off
function after platform handler finishes. This will put the core in low
power state and give a chance to wake it up.

Before this change, after running secondary kernel via kexec, only one
core was up, now both cores are up.

Change-Id: I87f144867550728055d9b8a2edb84a14539acab7
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Add two new functions 'plat_arm_sgi_get_platform_id' and
'plat_arm_sgi_get_config_id' which will be implemented by all the
SGI platforms. These functions can be used to determine the part
number and configuration id of the SGI platforms.

In BL2, these functions are used to populate the 'system-id' node.
In BL31, these functions are used to populate the 'sgi_plat_info_t'
structure with the part number and configuration id of the platform.

Change-Id: I3bacda933527724a3b4074ad4ed5b53a81ea4689
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

In order to allow Arm platforms to override the default list of PSCI
callbacks, remove the existing weak implementation of
'plat_arm_psci_override_pm_ops' function and let all the Arm platforms
implement their own 'plat_arm_psci_override_pm_ops' function.

For platforms that support SCMI protocol, the function
'css_scmi_override_pm_ops' can be additionally used as well to
override the default PSCI callbacks.

Change-Id: If7c27468bd51a00ea9c2a3716b5894163f5a9f3c
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

For platforms with multi-threaded CPUs, the number of power domains
supported would be more than the value currently defined by
PLAT_MAX_PWR_LVL. So move the PLAT_MAX_PWR_LVL macro to platform
specific code and let the platform define the number of power domain
levels.

Change-Id: I21c0682e62b397860b2999031a0c9c5ce0d28eed
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

To support platforms which are based on multi-threaded CPUs, override
the weak implementation of plat_arm_get_cpu_pe_count function to return
the number of threads supported by the CPU used in the platform.

Change-Id: Ia680773f1277b17e2d3d2414d87943dcece33e89
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

The CSS_SYSTEM_PWR_DMN_LVL macro that defines the system power domain
level is fixed at ARM_PWR_LVL2 for all CSS platforms. However, the
system power domain level can be different for CSS platforms that
use multi-threaded CPUs.

So, in preparation towards adding support for platforms that use
multi-threaded CPUs, refactor the definition of CSS_SYSTEM_PWR_DMN_LVL
such that CSS_SYSTEM_PWR_DMN_LVL is uniquely defined for each of the
CSS platform.

Change-Id: Ia837b13f6865e71da01780993c048b45b7f36d85
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

The headers forked at some point in the past and have diverged a lot. In
order to make it easier to share code between TF-A-Tests and TF-A, this
patch synchronises most of the definitions in the mentioned headers.

This is not a complete sync, it has to be followed by more cleanup.

This patch also removes the read helpers for the AArch32 instructions
ats1cpr and ats1hr (they are write-only).

Change-Id: Id13ecd7aeb83bd2318cd47156d71a42f1c9f6ba2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

commit 386b14bf64124ebf0368eab33ef07603e0c3138a
Author: Haojian Zhuang <haojian.zhuang@linaro.org>
Date:   Wed Nov 21 09:19:49 2018 +0800

    mmc: poll eMMC status after EXT_CSD command

    EXT_CSD command needs to access data from eMMC device. Add the
    operation of polling eMMC device status. Make sure the command is
    finished.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

A hacked delay time can't fit each eMMC device. Since the above commit
enables the polling operation, remove the hacked delay time now.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

This patch adds support to build a combined BL1
and ROMLIB binary file with the right page
alignment in Juno. When USE_ROMLIB=1 is set for
Juno, it generates the combined file
bl1_romlib.bin which needs to be used instead of
bl1.bin

Change-Id: I407efbe48d3e522fa6ef855538a9587193cb1919
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

Remove the platform common plat_arm_security_setup function to allow
platform specific implementations of the security setup function
implemented in the board directory of the platform.

For use by secure software, configure region0 of DMC-620 trustzone
controller to protect the upper 16MB of memory of the first DRAM block
from non-secure accesses.

Change-Id: I9a8c19656702c4fa4f6917b3655b692d443bb568
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

RCAR_RPC_HYPERFLASH_LOCKED can be set to 0 as a build option if the
user needs to allow u-boot to reprogram the ATF firmware using a FIP
image (as a faster alternative of toggling numerous DIP switches on
the board and using ascii-xfer of srec files)

The code being controlled with this commit should only be re-enabled for
debugging (_never_ on a product release)
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>

The default Raspberry Pi 3 memory mapping for ATF is geared towards
the use of uboot + Linux. This creates issues when trying to use
ATF with an UEFI payload and Windows on ARM64.

We therefore introduce new build option RPI3_USE_UEFI_MAP, that
enables the build process to use an alternate memory mapping that
is compatible with UEFI + Windows (as well as UEFI + Linux).

Fixes ARM-software/tf-issues#649
Signed-off-by: Pete Batard <pete@akeo.ie>

Some eMMC chips require a longer delay. After testing
different chips, 20ms appears to work reliably.
Signed-off-by: Ryan Grachek <ryan@edited.us>

Migrate Marvell platforms from legacy console API to
multi-console API.

Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Signed-off-by: Yann Gautier <yann.gautier@st.com>

According to "openssl" manual:
-K key
The actual key to use: this must be represented as a string
comprised only of hex digits. If only the key is specified,
the IV must additionally specified using the -iv option.
When both a key and a password are specified, the key given
with the -K option will be used and the IV generated from the
password will be taken.
It does not make much sense to specify both key and password.

This patch removes "-k 0" parameter from the encryption command
since we are already using "-K" and "-iv" for the key and IV.

Change-Id: Ia333cedaa3207e643c95d2ec7c229f50eeab96db
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/60745

Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Sharon Habet <sharonh@marvell.com>

The DCDC6 power rail is typically driving VDD_SYS in the SoC, so it is
on by default and uses the default voltage.

As there seems to be at least on board using a different voltage, add
the rail to the list of known voltage lines, so we can setup the right
voltage as early as possible.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The DCDC1 and DCDC5 power rails didn't specify the enable bits. This
isn't critical, since those rails are on by default (and are needed for
every board), but it is inconsistent.

Add the respective enable bits for those two rails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The DRIVEVBUS pin setup was broken in two ways:
- To configure this pin as an output pin, one has to *clear* the bit in
  register 0x8f. It is 0 by default, but rebooting from Linux might have
  left this bit set.
- Doing this just configures the pin as an output pin, but doesn't
  actually drive power to it. This is done via bit 2 in register 0x30.

Fix the routine to both properly configure the pin and drive power to
it. Add an axp_clrsetbits() helper on the way.

Now this isn't really perfect, still:
We only need to setup the PMIC power rails that are needed for U-Boot.
DRIVEVBUS typically controls the VBUS voltage for the host function of
an USB-OTG port, something we typically don't want in U-Boot (fastboot,
using the USB *device* functionality, is much more common). The
BananaPi-M64 uses the regulator in this way, but the Remix Mini PC
actually controls the power of both its USB ports via this line.

Technically we should differentiate here: if DRIVEVBUS controls a
microUSB-B socket, the power should stay off, any host-type A sockets
should be supplied, though.
For now just always enable the power, that shouldn't really hurt the
USB-OTG functionality anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The legacy Allwinner ATF port used to setup some clocks, and U-Boot is
still relying on this. We don't need to setup the full set, as the SPL
is doing most of it, but it misses one clock (AHB2) and programs another
(AHB1) to quite conservative values.

Fix this up during the platform setup to improve USB and Ethernet
performance, iperf values go up by 31% in my setup with that patch.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Register a priority level, PLAT_SP_PRI, for secure partition with EL3
exception handling framework(ehf) module.

The secure partition manager(SPM) would raise the core's priority to
PLAT_SP_PRI before entering the secure partition, to protect the core
from getting interrupted while in secure partition.

Change-Id: I686897f052a4371e0efa9b929c07d3ad77249e95
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

Some OSes (e.g. Ubuntu 18.04 LTS on Raspberry Pi 3) may disable the
runtime UART in a manner that prevents the system from rebooting if
ATF tries to send runtime messages there.

Also, we don't want the firmware to share the UART with normal
world, as this can be a DoS attack vector into the secure world.

This patch fixes these 2 issues by introducing new build option
RPI3_RUNTIME_UART, that disables the runtime UART by default.

Fixes ARM-software/tf-issues#647
Signed-off-by: Pete Batard <pete@akeo.ie>

These issues wer found by sparse:

drivers/st/clk/stm32mp1_clk.c:1524:19:
 warning: incorrect type in assignment (different base types)
    expected restricted fdt32_t const [usertype] *pkcs_cell
    got unsigned int const [usertype] *

plat/st/stm32mp1/plat_image_load.c:13:6:
 warning: symbol 'plat_flush_next_bl_params' was not declared.
 Should it be static?
plat/st/stm32mp1/plat_image_load.c:21:16:
 warning: symbol 'plat_get_bl_image_load_info' was not declared.
 Should it be static?
plat/st/stm32mp1/plat_image_load.c:29:13:
 warning: symbol 'plat_get_next_bl_params' was not declared.
 Should it be static?

plat/st/stm32mp1/bl2_io_storage.c:40:10:
 warning: symbol 'block_buffer' was not declared. Should it be static?
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine Scalar
Processing Engines, Adaptable Hardware Engines, and Intelligent Engines with
leading-edge memory and interfacing technologies to deliver powerful
heterogeneous acceleration for any application. The Versal AI Core series has
five devices, offering 128 to 400 AI Engines. The series includes dual-core Arm
Cortex-A72 application processors, dual-core Arm Cortex-R5 real-time
processors, 256KB of on-chip memory with ECC, more than 1,900 DSP engines
optimized for high-precision floating point with low latency.

This patch adds Virtual QEMU platform support for
this SoC "versal_virt".
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.
Enables building with ERROR_DEPRECATED=1.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.
Enables building with ERROR_DEPRECATED=1.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.
Enables building with ERROR_DEPRECATED=1.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I2419416fadfcdf64da8b7690a348007591c4edf3
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Target builds but has not been tested.
Signed-off-by: ldts <jorge.ramirez.ortiz@gmail.com>

Signed-off-by: ldts <jorge.ramirez.ortiz@gmail.com>

This option allows the Trusted Firmware to directly jump to Linux
kernel for aarch32 without the need of an intermediate loader such
as U-Boot.

Similar to AArch64 ARM_LINUX_KERNEL_AS_BL33 only available with
RESET_TO_SP_MIN=1 as well as BL33 and DTB are preloaded in memory.

Change-Id: I908bc1633696be1caad0ce2f099c34215c8e0633
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

When CSS_USE_SCMI_DRIVER is not defined or set to 0, we get the
following build error.

plat/arm/board/juno/juno_topology.c:16:19: error: ‘CSS_SCMI_PAYLOAD_BASE’ undeclared here (not in a function)
   .scmi_mbx_mem = CSS_SCMI_PAYLOAD_BASE,
                   ^~~~~~~~~~~~~~~~~~~~~
plat/arm/board/juno/juno_topology.c:17:38: error: ‘CSS_SCMI_MHU_DB_REG_OFF’ undeclared here (not in a function)
   .db_reg_addr = PLAT_CSS_MHU_BASE + CSS_SCMI_MHU_DB_REG_OFF,
                                      ^~~~~~~~~~~~~~~~~~~~~~~
                                      CSS_CPU_PWR_STATE_OFF

Fix the error in order to get function legacy SCPI support functional.

Change-Id: I00cb80db9968aa0be546e33a3a682a2db87719be
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>