GitLab

The raw NAND framework supports SLC NAND devices.

It introduces a new high level interface (io_mtd) that
defines operations a driver can register to the NAND framework.
This interface will fill in the io_mtd device specification:
	- device_size
        - erase_size
that could be used by the io_storage interface.

NAND core source file integrates the standard read loop that
performs NAND device read operations using a skip bad block strategy.
A platform buffer must be defined in case of unaligned
data. This buffer must fit to the maximum device page size
defined by PLATFORM_MTD_MAX_PAGE_SIZE.

The raw_nand.c source file embeds the specific NAND operations
to read data.
The read command is a raw page read without any ECC correction.
This can be overridden by a low level driver.
No generic support for write or erase command or software
ECC correction.

NAND ONFI detection is available and can be enabled using
NAND_ONFI_DETECT=1.
For non-ONFI NAND management, platform can define required
information.

Change-Id: Id80e9864456cf47f02b74938cf25d99261da8e82
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

IO seek offset can be set to values above UINT32_MAX, this change
changes the seek offset argument from 'ssize_t' to 'signed long long'.
Fixing platform seek functions to match the new interface update.

Change-Id: I25de83b3b7abe5f52a7b0fee36f71e60cac9cfcb
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

NOTE for platform integrators:
   API `plat_psci_stat_get_residency()` third argument
   `last_cpu_idx` is changed from "signed int" to the
   "unsigned int" type.

Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.

2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent

Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.

Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c

In further patches, we wish to enable -wredundant-decls check as
part of warning flags by default.

Change-Id: I43410d6dbf40361a503c16d94ccf0f4cf29615b7
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

Now that DDR drivers are mostly cleaned up , move them out of staging.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: I9de63f847a0ef9ac27a79fb0f848c351fd7f4da6

The SCU connects one to four Cortex-A5/Cortex-A9 processors
to the memory system through the AXI interfaces.

The SCU functions are to:
- maintain data cache coherency between the Cortex-A5/Cortex-A9
  processors
- initiate L2 AXI memory accesses
- arbitrate between Cortex-A5/Cortex-A9 processors requesting
  L2 accesses
- manage ACP accesses.

Snoop Control Unit will enable to snoop on other CPUs caches.
This is very important when it comes to synchronizing data between
CPUs. As an example, there is a high chance that data might be
cache'd and other CPUs can't see the change. In such cases,
if snoop control unit is enabled, data is synchoronized immediately
between CPUs and the changes are visible to other CPUs.

This driver provides functionality to enable SCU as well as enabling
user to know the following
- number of CPUs present
- is a particular CPU operating in SMP mode or AMP mode
- data cache size of a particular CPU
- does SCU has ACP port
- is L2CPRESENT

Change-Id: I0d977970154fa60df57caf449200d471f02312a0
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>

On some platforms the UART might have already been initialised, for
instance by firmware running before TF-A or by a separate management
processor. In this case it would not be need to initialise it again
(doing so could create spurious characters). But more importantly this
saves us from knowing the right baudrate and the right base clock rate
for the UART. This can lead to more robust and versatile firmware builds.

Allow to skip the 16550 UART initialisation and baud rate divisor
programming, by interpreting an input clock rate of "0" to signify this
case. This will just skip the call to console_16550_core_init, but still
will register the console properly.

Users should just pass 0 as the second parameter, the baudrate (third
parameter) will then be ignored as well.

Fix copy & paste typos in comments for the console_16550_register()
function on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Change-Id: I9f8fca5b358f878fac0f31dc411358fd160786ee

Previously, the A64/H5 and H6 platforms' PMIC setup code was entirely
independent. However, some H6 boards also need early regulator setup.

Most of the register interface and all of the device tree traversal code
can be reused between the AXP803 and AXP805. The main difference is the
hardware bus interface, so that part is left to the platforms. The
remainder is moved into a driver.

I factored out the bits that were obviously specific to the AXP803;
additional changes for compatibility with other PMICs can be made as
needed.

The only functional change is that rsb_init() now checks the PMIC's chip
ID register against the expected value. This was already being done in
the H6 version of the code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Icdcf9edd6565f78cccc503922405129ac27e08a2

This adds the new regulator list, as well as changes to make the switch
(equivalent to DC1SW on the AXP803) work on both PMICs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I9a1eac8ddfc54b27096c10a8eebdd51aaf9b8311

Add support for powering off the SGMII COMPHY (on lanes 0 and 1).
This is needed sometimes on Turris Mox when using KEXEC.

There is also another benefit of a little energy saving when the given
network interface is down.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I55ae0fe3627e7cc0f65c78a00771939d8bf5399f

When USB3 is on lane 2 and indirect register access is used, the polling
at the end of the mvebu_a3700_comphy_usb3_power_on function is
incorrect.

The LOOPBACK_REG0 register should not be used at all. Instead we have to
write the LANE_STATUS1 register address (with offset
USB3PHY_LANE2_REG_BASE_OFFSET) into the indirect address register and
then we should poll indirect data register.

This fixes problems on Turris Mox, which uses lane 2 for USB3.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I968b0cccee5ddbe10a2b5614e52e52d87682aacd

Add the support needed to enable using CryptoCell integration with
with RSA 3K support.
Signed-off-by: Gilad Ben-Yossef <gilad.benyossef@arm.com>
Change-Id: I95527cb0c41ae012109e8968dd20a4ae9fe67f17

As supporting architectures aside from AArch32 and AArch64 is not a
concern, keeping identical definitions in two places for a large part
of the libc seems counterproductive

The int128 types were left un-unified as __int128 is not supported by
gcc on AArch32
Signed-off-by: Bence Szépkúti <bence.szepkuti@arm.com>
Change-Id: Idf08e6fab7e4680d9da62d3c57266ea2d80472cf

-Wlogical-op prevents common errors with using numerical constants where
a boolean one is expected as well as when the operands of a logical
operator are the same. While these are perfectly valid behavior, they
can be a sign that something is slightly off.

This patch adds this warning to gcc and it's closest equivalent to
clang, while also fixing any warnings that enabling them causes.

Change-Id: Iabadfc1e6ee0c44eef6685a23b0aed8abef8ce89
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>

Variable shadowing is, according to the C standard, permitted and valid
behaviour. However, allowing a local variable to take the same name as a
global one can cause confusion and can make refactoring and bug hunting
more difficult.

This patch moves -Wshadow from WARNING2 into the general warning group
so it is always used. It also fixes all warnings that this introduces
by simply renaming the local variable to a new name

Change-Id: I6b71bdce6580c6e58b5e0b41e4704ab0aa38576e
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>

Change-Id: Ia120bcaacea3a462ab78db13f84ed23493033601
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>

Arm's GIC-600 features a Power Register (GICR_PWRR),
which needs to be programmed to enable redistributor
operation. Section 3.6.1 in the GIC-600 TRM describes
the power-up and power-down sequence in pseudo code,
which deviates from the current TF-A implementation
in drivers/arm/gic/v3/gic600.c.
For powering on a redistributor, the pseudo code suggests
to loop over the whole sequence (check for transition,
write request bit) instead of just looping over the
ready bit read as TF-A does in gic600_pwr_on().
This patch fixes GIC-600 power up sequence according
to the TRM.

Change-Id: I445c480e96ba356b69a2d8e5308ffe6c0a97f45b
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Previous implementation of timers assumed that clk_div has pretty
representation in MHz (10MHz, 100MHz, etc). Unusual frequencies
(99.99MHz) were causing assertion error and made udelay unusable.
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: Ic915fff224369d113fd9f8edbcfff169fca8beac

Add support to configure GIC-600's multichip routing table registers.
Introduce a new gic600 multichip structure in order to support platforms
to pass their GIC-600 multichip information such as routing table owner,
SPI blocks ownership.

This driver is currently experimental and the driver api may change in
the future.

Change-Id: Id409d0bc07843e271ead3fc2f6e3cb38b317878d
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

Instead of retry polling, timer of 1ms is used to poll
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: I7e028dc68138d2888e3cf0cbed744f5e6bc6ff42

Currently for Armv7 plaforms the quotient calculated in pl011
uart init code is moved to register r1.

This patch moves the quotient to register r2 as done for other
platforms in the udiv instruction. Value of register r2 is then
used to calculate the values for IBRD and FBRD register

Change-Id: Ie6622f9f0e6d634378b471df5d02823b492c8a24
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>

Change-Id: I84f8a99be2dcdf7c51fbecdb324df8e2f32cc855
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>

In the SD Specification, Power Up Diagram of Card figure, the Timeout
value for initialization process (ACMD41 command retries) is 1 second.
Align to match MMC cards (in mmc_send_op_cond()) and Linux kernel code,
and set the delay between ACMD41 command retries to 10ms.

Change-Id: I2e07cb9944e7d7b72f2d4b13e0505e6751458091
Signed-off-by: Yann Gautier <yann.gautier@st.com>

This patch provides declaration and definition of new GICv3 driver
API: gicv3_rdistif_probe().This function delegates the responsibility
of discovering the corresponding Redistributor base frame to each CPU
itself. It is a modified version of gicv3_rdistif_base_addrs_probe()
and is executed by each CPU in the platform unlike the previous
approach in which only the Primary CPU did the discovery of all the
Redistributor frames for every CPU.

The flush operations as part of gicv3_driver_init() function are
made necessary even for platforms with WARMBOOT_ENABLE_DCACHE_EARLY
because the GICv3 driver data structure contents are accessed by CPU
with D-Cache turned off during power down operations.

Change-Id: I1833e81d3974b32a3e4a3df4766a33d070982268
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

This commit adds authentication binary support for STM32MP1.
It prints the bootrom authentication result if signed
image is used and authenticates the next loaded STM32 images.
It also enables the dynamic translation table support
(PLAT_XLAT_TABLES_DYNAMIC) to use bootrom services.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Iba706519e0dc6b6fae1f3dd498383351f0f75f51

This BSEC service is a platform specific service. Implementation
moved to the platform part.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I1f70ed48a446860498ed111acce01187568538c9

The driver manages the HASH processor IP on STM32MP1
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I3b67c80c16d819f86b951dae29a6c465e51ad585

The block size of some storage device is 4096-byte long, such as UFS. But
PARTITION_BLOCK_SIZE is defined as 512-byte long. So replace it by
PLAT_PARTITION_BLOCK_SIZE. Make it configurable in platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Change-Id: Iada05f7c646d0a0f2c0d3b8545540b3cb7153de3

The registers location for the SHA DMA driver is not unique for the
different platforms. Move the mapping out of the driver and into the
platform-specific header.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Change-Id: Ice64637844a3cb384b01e466cb8c1cea5f764129

To allow sharing the driver between the RPi3 and RPi4, move the random
number generator driver into the generic driver directory.

Change-Id: Iae94d7cb22c6bce3af9bff709d76d4caf87b14d1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

To allow sharing the driver between the RPi3 and RPi4, move the mailbox
driver into the generic driver directory.

Change-Id: I463e49acf82b02bf004f3d56482b7791f3020bc0
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch fixes GICv3 driver bug which causes assertion
when full range of SPI INTIDs 32-1019 is supported in
GICv3 implementation.

Change-Id: Ib6da4b6eea868cff271cb32c7c7570bf5547ab47
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Support for PKCS#1 v1.5 was deprecated in SHA 1001202d and fully removed
in SHA fe199e3b

, however, cert_tool is still able to generate
certificates in that form. This patch fully removes the ability for
cert_tool to generate these certificates.

Additionally, this patch also fixes a bug where the issuing certificate
was a RSA and the issued certificate was EcDSA. In this case, the issued
certificate would be signed using PKCS#1 v1.5 instead of RSAPSS per
PKCS#1 v2.1, preventing TF-A from verifying the image signatures. Now
that PKCS#1 v1.5 support is removed, all certificates that are signed
with RSA now use the more modern padding scheme.

Change-Id: Id87d7d915be594a1876a73080528d968e65c4e9a
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>

Previously, TF-A could not support large RSA key sizes as the
configuration options passed to MBEDTLS prevented storing and performing
calculations with the larger, higher-precision numbers required. With
these changes to the arguments passed to MBEDTLS, TF-A now supports
using 3072 (3K) and 4096 (4K) keys in certificates.

Change-Id: Ib73a6773145d2faa25c28d04f9a42e86f2fd555f
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>

The STM32 console driver was pre-pending '\r' before '\n'.
It is now managed by the framework with the flag:
CONSOLE_FLAG_TRANSLATE_CRLF.
Remove the code in driver, and add the flag for STM32MP1.

Change-Id: I5d0d5d5c4abee0b7dc11c2f8707b1b5cf10149ab
Signed-off-by: Yann Gautier <yann.gautier@st.com>

The SHA256 DMA driver can be used by multiple SoCs. Move it to the
common directory.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Change-Id: I96319eeeeeebd503ef0dcb07c0e4ff6a67afeaa5

Meson is the internal code name for the SoC family. The correct name for
the platform should be Amlogic. Change the name of the platform
directory.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Change-Id: Icc140e1ea137f12117acbf64c7dcb1a8b66b345d

DBLOCKSIZE should be filled such as the data size is 2^DBLOCKSIZE.
Hence it is calculated with __builtin_ctz.

Change-Id: Id6b5ff9b594afc4fc523a388011beed307e6abd1
Signed-off-by: Yann Gautier <yann.gautier@st.com>

If the max-frequency property is provided in the device tree mmc node,
it should be managed. The max allowed frequency will be the min between
this property value and what the card can support.

Change-Id: I885b676c3300d2670a0fe4c6ecab87758b5893ad
Signed-off-by: Yann Gautier <yann.gautier@st.com>

This function can be used on several stm32mp devices, it is then moved in
plat/st/common/stm32mp_common.c.

Change-Id: I862debe39604410f71a9ddc28713026362e9ecda
Signed-off-by: Yann Gautier <yann.gautier@st.com>