GitLab

The raw NAND framework supports SLC NAND devices.

It introduces a new high level interface (io_mtd) that
defines operations a driver can register to the NAND framework.
This interface will fill in the io_mtd device specification:
	- device_size
        - erase_size
that could be used by the io_storage interface.

NAND core source file integrates the standard read loop that
performs NAND device read operations using a skip bad block strategy.
A platform buffer must be defined in case of unaligned
data. This buffer must fit to the maximum device page size
defined by PLATFORM_MTD_MAX_PAGE_SIZE.

The raw_nand.c source file embeds the specific NAND operations
to read data.
The read command is a raw page read without any ECC correction.
This can be overridden by a low level driver.
No generic support for write or erase command or software
ECC correction.

NAND ONFI detection is available and can be enabled using
NAND_ONFI_DETECT=1.
For non-ONFI NAND management, platform can define required
information.

Change-Id: Id80e9864456cf47f02b74938cf25d99261da8e82
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

IO seek offset can be set to values above UINT32_MAX, this change
changes the seek offset argument from 'ssize_t' to 'signed long long'.
Fixing platform seek functions to match the new interface update.

Change-Id: I25de83b3b7abe5f52a7b0fee36f71e60cac9cfcb
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

The SCU connects one to four Cortex-A5/Cortex-A9 processors
to the memory system through the AXI interfaces.

The SCU functions are to:
- maintain data cache coherency between the Cortex-A5/Cortex-A9
  processors
- initiate L2 AXI memory accesses
- arbitrate between Cortex-A5/Cortex-A9 processors requesting
  L2 accesses
- manage ACP accesses.

Snoop Control Unit will enable to snoop on other CPUs caches.
This is very important when it comes to synchronizing data between
CPUs. As an example, there is a high chance that data might be
cache'd and other CPUs can't see the change. In such cases,
if snoop control unit is enabled, data is synchoronized immediately
between CPUs and the changes are visible to other CPUs.

This driver provides functionality to enable SCU as well as enabling
user to know the following
- number of CPUs present
- is a particular CPU operating in SMP mode or AMP mode
- data cache size of a particular CPU
- does SCU has ACP port
- is L2CPRESENT

Change-Id: I0d977970154fa60df57caf449200d471f02312a0
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>

On some platforms the UART might have already been initialised, for
instance by firmware running before TF-A or by a separate management
processor. In this case it would not be need to initialise it again
(doing so could create spurious characters). But more importantly this
saves us from knowing the right baudrate and the right base clock rate
for the UART. This can lead to more robust and versatile firmware builds.

Allow to skip the 16550 UART initialisation and baud rate divisor
programming, by interpreting an input clock rate of "0" to signify this
case. This will just skip the call to console_16550_core_init, but still
will register the console properly.

Users should just pass 0 as the second parameter, the baudrate (third
parameter) will then be ignored as well.

Fix copy & paste typos in comments for the console_16550_register()
function on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Change-Id: I9f8fca5b358f878fac0f31dc411358fd160786ee

Previously, the A64/H5 and H6 platforms' PMIC setup code was entirely
independent. However, some H6 boards also need early regulator setup.

Most of the register interface and all of the device tree traversal code
can be reused between the AXP803 and AXP805. The main difference is the
hardware bus interface, so that part is left to the platforms. The
remainder is moved into a driver.

I factored out the bits that were obviously specific to the AXP803;
additional changes for compatibility with other PMICs can be made as
needed.

The only functional change is that rsb_init() now checks the PMIC's chip
ID register against the expected value. This was already being done in
the H6 version of the code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Icdcf9edd6565f78cccc503922405129ac27e08a2

This adds the new regulator list, as well as changes to make the switch
(equivalent to DC1SW on the AXP803) work on both PMICs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I9a1eac8ddfc54b27096c10a8eebdd51aaf9b8311

Add the support needed to enable using CryptoCell integration with
with RSA 3K support.
Signed-off-by: Gilad Ben-Yossef <gilad.benyossef@arm.com>
Change-Id: I95527cb0c41ae012109e8968dd20a4ae9fe67f17

Add support to configure GIC-600's multichip routing table registers.
Introduce a new gic600 multichip structure in order to support platforms
to pass their GIC-600 multichip information such as routing table owner,
SPI blocks ownership.

This driver is currently experimental and the driver api may change in
the future.

Change-Id: Id409d0bc07843e271ead3fc2f6e3cb38b317878d
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

The function has to use read_cntpct_el0() to update the counter, and not
read_cntfrq_el0().

Change-Id: I9c676466e784c3122e9ffc2d87e66708797086e7
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Introduce timeout_init_us/timeout_elapsed() delay tracking with CNTPCT.

timeout_init_us(some_timeout_us); returns a reference to detect
timeout for the provided microsecond delay value from current time.

timeout_elapsed(reference) return true/false whether the reference
timeout is elapsed.

Cherry picked from OP-TEE implementation [1].
  [1] commit 33d30a74502b ("core: timeout detection support")

Minor:
- Remove stm32mp platform duplicated implementation.
- Add new include in marvell ble.mk
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Iaef6d43c11a2e6992fb48efdc674a0552755ad9c

Use size_t for length parameter in header file, as in .c file.

Change-Id: I310f2a6159cde1c069b4f814f6558c2488c203ec
Signed-off-by: Yann Gautier <yann.gautier@st.com>

This patch provides declaration and definition of new GICv3 driver
API: gicv3_rdistif_probe().This function delegates the responsibility
of discovering the corresponding Redistributor base frame to each CPU
itself. It is a modified version of gicv3_rdistif_base_addrs_probe()
and is executed by each CPU in the platform unlike the previous
approach in which only the Primary CPU did the discovery of all the
Redistributor frames for every CPU.

The flush operations as part of gicv3_driver_init() function are
made necessary even for platforms with WARMBOOT_ENABLE_DCACHE_EARLY
because the GICv3 driver data structure contents are accessed by CPU
with D-Cache turned off during power down operations.

Change-Id: I1833e81d3974b32a3e4a3df4766a33d070982268
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

This BSEC service is a platform specific service. Implementation
moved to the platform part.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I1f70ed48a446860498ed111acce01187568538c9

The driver manages the HASH processor IP on STM32MP1
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I3b67c80c16d819f86b951dae29a6c465e51ad585

The block size of some storage device is 4096-byte long, such as UFS. But
PARTITION_BLOCK_SIZE is defined as 512-byte long. So replace it by
PLAT_PARTITION_BLOCK_SIZE. Make it configurable in platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Change-Id: Iada05f7c646d0a0f2c0d3b8545540b3cb7153de3

To allow sharing the driver between the RPi3 and RPi4, move the random
number generator driver into the generic driver directory.

Change-Id: Iae94d7cb22c6bce3af9bff709d76d4caf87b14d1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

To allow sharing the driver between the RPi3 and RPi4, move the mailbox
driver into the generic driver directory.

Change-Id: I463e49acf82b02bf004f3d56482b7791f3020bc0
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Previously, TF-A could not support large RSA key sizes as the
configuration options passed to MBEDTLS prevented storing and performing
calculations with the larger, higher-precision numbers required. With
these changes to the arguments passed to MBEDTLS, TF-A now supports
using 3072 (3K) and 4096 (4K) keys in certificates.

Change-Id: Ib73a6773145d2faa25c28d04f9a42e86f2fd555f
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>

The SHA256 DMA driver can be used by multiple SoCs. Move it to the
common directory.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Change-Id: I96319eeeeeebd503ef0dcb07c0e4ff6a67afeaa5

Meson is the internal code name for the SoC family. The correct name for
the platform should be Amlogic. Change the name of the platform
directory.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Change-Id: Icc140e1ea137f12117acbf64c7dcb1a8b66b345d

The #include "mbedtls/check_config.h" directive first searches for
the header in the relative path to mbedtls_config.h, i.e.
include/drivers/auth/mbedtls/mbedtls/check_config.h

Obviously, it does not exist since check_config.h is located in
the mbedtls project.

It is more sensible to use #include <...> form.

Change-Id: If72a71381f84e7748a2c9f07dd1176559d9bb1d2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

If the max-frequency property is provided in the device tree mmc node,
it should be managed. The max allowed frequency will be the min between
this property value and what the card can support.

Change-Id: I885b676c3300d2670a0fe4c6ecab87758b5893ad
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Introduce driver for STM32 IWDG peripheral (Independent Watchdog).
It is configured according to device tree content and should be enabled
from there.
The watchdog is not started by default. It can be started after an HW
reset if the dedicated OTP is fused.

The watchdog also needs to be frozen if a debugger is attached.
This is done by configuring the correct bits in DBGMCU.
This configuration is allowed by checking BSEC properties.

An increase of BL2 size is also required when adding this new code.

Change-Id: Ide7535d717885ce2f9c387cf17afd8b5607f3e7f
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

Currently, console drivers prepend '\r' to '\n' by themselves. This is
common enough to be supported in the framework.

Add a new flag, CONSOLE_FLAG_TRANSLATE_CRLF. A driver can set this
flag to ask the framework to transform LF into CRLF instead of doing
it by itself.

Change-Id: I4f5c5887591bc0a8749a105abe62b6562eaf503b
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

NOTE: __ASSEMBLY__ macro is now deprecated in favor of __ASSEMBLER__.

All common C compilers predefine a macro called __ASSEMBLER__ when
preprocessing a .S file. There is no reason for TF-A to define it's own
__ASSEMBLY__ macro for this purpose instead. To unify code with the
export headers (which use __ASSEMBLER__ to avoid one extra dependency),
let's deprecate __ASSEMBLY__ and switch the code base over to the
predefined standard.

Change-Id: Id7d0ec8cf330195da80499c68562b65cb5ab7417
Signed-off-by: Julius Werner <jwerner@chromium.org>

Add support for multiple Cryptocell revisions which
use different APIs.

This commit only refactors the existing code in preperation to the addition
of another Cryptocell revisions later on.
Signed-off-by: Gilad Ben-Yossef <gilad.benyossef@arm.com>
Change-Id: I16d80b31afb6edd56dc645fee5ea619cc74f09b6

Code using Cryptocell specific APIs was used as part of the
arm common board ROT support, instead of being abstracted
in Cryptocell specific driver code, creating two problems:
- Any none arm board that uses Cryptocell wuld need to
  copy and paste the same code.
- Inability to cleanly support multiple versions of Cryptocell
  API and products.

Move over Cryptocell specific API calls into the Cryptocell
driver, creating abstraction API where needed.
Signed-off-by: Gilad Ben-Yossef <gilad.benyossef@arm.com>
Change-Id: I9e03ddce90fcc47cfdc747098bece86dbd11c58e

This patch adds a new include/export/ directory meant for inclusion in
third-party code. This is useful for cases where third-party code needs
to interact with TF-A interfaces and data structures (such as a custom
BL2-implementation like coreboot handing off to BL31). Directly
including headers from the TF-A repository avoids having to duplicate
all these definitions (and risk them going stale), but with the current
header structure this is not possible because handoff API definitions
are too deeply intertwined with other TF code/headers and chain-include
other headers that will not be available in the other environment.

The new approach aims to solve this by separating only the parts that
are really needed into these special headers that are self-contained and
will not chain-include other (non-export) headers. TF-A code should
never include them directly but should instead always include the
respective wrapper header, which will include the required prerequisites
(like <stdint.h>) before including the export header. Third-party code
can include the export headers via its own wrappers that make sure the
necessary definitions are available in whatever way that environment can
provide them.

Change-Id: Ifd769320ba51371439a8e5dd5b79c2516c3b43ab
Signed-off-by: Julius Werner <jwerner@chromium.org>

This consists of ensuring that the left operand of each shift is
unsigned when the operation might overflow into the sign bit.

Change-Id: Iddd6f38139a4c6e500468b4fc48d04e0939f574e
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>

The new API becomes the default one.

Change-Id: Ic1d602da3dff4f4ebbcc158b885295c902a24fec
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

Rework the macro that eases the table definition: the src and msk fields
are now using MASK and SHIFT defines of each source register.
Some macros had then to be modified: _USART1_SEL, _ASS_SEL and _MSS_SEL to
_UART1_SEL, _AXIS_SEL, and _MCUS_SEL to match register fields.

Note: the mask for RCC_ASSCKSELR_AXISSRC is changed from 0x3 to 0x7
to reflect the size of the register field, even if there are only
3 possible clock sources.

The mask value is also corrected for QSPI and FMC clock selection.

Change-Id: I44114e3c1dd37b9fa1be1ba519611abd9a07764c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

Those functions are generic for parsing nodes from device tree
hence could be located in generic source file.

The oscillators description structure is also moved to STM32MP1 clock
driver, as it is no more used in stm32mp1_clkfunc and cannot be in a
generic file.

Change-Id: I93ba74f4eea916440fef9b160d306af1b39f17c6
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Convert the R-Car Gen3 platform and both SCIF and Log drivers
to multi-console API.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: I18556973937d150b60453f9150d54ee612571e35

The chain of trust description and the pointer pointing to its first
element were incompatible, thus requiring an explicit type cast for
the assignment.

- cot_desc was an array of
  const pointers to const image descriptors.

- cot_desc_ptr was a const pointer to
  (non-constant) pointers to const image descriptors.

Thus, trying to assign cot_desc to cot_desc_ptr (with no cast) would
generate the following compiler warning:

drivers/auth/tbbr/tbbr_cot.c:826:14: warning: initialization discards
  ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
 REGISTER_COT(cot_desc);
              ^~~~~~~~

Change-Id: Iae62dd1bdb43fe379e3843d96461d47cc2f68a06
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

For security DMA should be blocked at the SMMU by default
unless explicitly enabled for a device. SMMU is disabled
after reset with all streams bypassing the SMMU, and
abortion of all incoming transactions implements a default
deny policy on reset.
This patch also moves "bl1_platform_setup()" function from
arm_bl1_setup.c to FVP platforms' fvp_bl1_setup.c and
fvp_ve_bl1_setup.c files.

Change-Id: Ie0ffedc10219b1b884eb8af625bd4b6753749b1a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch is a preparation for the subsequent changes in
SMMUv3 driver. It introduces a new "smmuv3_poll" function
and replaces inline functions for accessing SMMU registers
with mmio read/write operations. Also the infinite loop
for the poll has been replaced with a counter based timeout.

Change-Id: I7a0547beb1509601f253e126b1a7a6ab3b0307e7
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Add a driver for configuring the SBSA Generic Watchdog which aids in
the detection of errant system behaviour.

Change-Id: I5a1e7149c69fd8b85be7dfbcf511f431339946f4
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

This changes the auth_img_desc_t struct to have pointers to struct
arrays instead of struct arrays. This saves memory as many of these
were never used, and can be NULL pointers. Note the memory savings are
only when these arrays are not initialised, as it is assumed these
arrays are fixed length. A possible future optimisation could allow for
variable length.

memory diff:
bl1:        bl2:
    text        text
      -12         -12
    bss         bss
      -1463       0
    data        data
      -56         -48
    rodata      rodata
      -5688       -2592
    total       total
      -7419       -2652

Change-Id: I8f9bdedf75048b8867f40c56381e3a6dc6402bcc
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>

When Trusted Board Boot is enabled, we need to specify the Chain of
Trust (CoT) of the BL1 and BL2 images. A CoT consists of an array
of image descriptors. The authentication module assumes that each
image descriptor in this array is indexed by its unique image
identifier. For example, the Trusted Boot Firmware Certificate has to
be at index [TRUSTED_BOOT_FW_CERT_ID].

Unique image identifiers may not necessarily be consecutive. Also,
a given BL image might not use all image descriptors. For example, BL1
does not need any of the descriptors related to BL31. As a result, the
CoT array might contain holes, which unnecessarily takes up space in
the BL binary.

Using pointers to auth_img_desc_t structs (rather than structs
themselves) means these unused elements only use 1 pointer worth of
space, rather than one struct worth of space. This patch also changes
the code which accesses this array to reflect the change to pointers.

Image descriptors not needed in BL1 or BL2 respectively are also
ifdef'd out in this patch. For example, verifying the BL31 image is
the responsibility of BL2 so BL1 does not need any of the data
structures describing BL31.

memory diff:
bl1:        bl2:
    text        text
      -20         -20
    bss         bss
      -1463       0
    data        data
      -256        -48
    rodata      rodata
      -5240       -1952
    total       total
      -6979       -2020

Change-Id: I163668b174dc2b9bbb183acec817f2126864aaad
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>

Types tzc_action_t and tzc_region_attributes_t are deprecated.

Change-Id: Ieefeb8521a0e1130f39d09b5c0d2728f05084773
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>