GitLab

The Marvell Armada 37xx SoCs-based platforms contain a bit
awkward directory structure because the currently only one
supported PLAT and PLAT_FAMILY are the same. Modify the latter
to 'a3k' in order to improve it and keep plat/marvell/armada
tree more consistent:

plat/marvell/
├── armada
│   ├── a3k
│   │   ├── a3700

[...]

│   ├── a8k
│   │   ├── a70x0

[...]

Change-Id: I693a6ef88e6ce49a326a3328875c90bbc186066a
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

Using the fconf framework, the Group 0 and Group 1 secure interrupt
descriptors are moved to device tree and retrieved in runtime. This
feature is enabled by the build flag SEC_INT_DESC_IN_FCONF.

Change-Id: I360c63a83286c7ecc2426cd1ff1b4746d61e633c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
plat, include/plat) are moved to the new "armada" sub-folder.

Change-Id: Icf03356187078ad6a2e56c9870992be3ca4c9655
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

The patch fixes BL31 linker script error
"Init code ends past the end of the stacks"
for platforms with number of CPUs less than 4,
which is caused by __STACKS_END__ address being
lower than __INIT_CODE_END__.
The modified BL31 linker script detects such cases
and increases the total amount of stack memory,
setting __STACKS_END__ = __INIT_CODE_END__, and
CPUs' stacks are calculated by BL31 'plat_get_my_stack'
function accordingly. For platforms with more than 4 CPUs
and __INIT_CODE_END__ < __STACKS_END__ stack memory does not
increase and allocated CPUs' stacks match the existing
implementation.
The patch removes exclusion of PSCI initialization
functions from the reclaimed .init section in
'arm_reclaim_init.ld.S' script, which increases the
size of reclaimed memory region.

Change-Id: I927773e00dd84e1ffe72f9ee534f4f2fc7b6153c
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch introduces dynamic configuration for SDEI setup and is supported
when the new build flag SDEI_IN_FCONF is enabled. Instead of using C arrays
and processing the configuration at compile time, the config is moved to
dts files. It will be retrieved at runtime during SDEI init, using the fconf
layer.

Change-Id: If5c35a7517ba00a9f258d7f3e7c8c20cee169a31
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Co-authored-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

Currently BL2 passes TOS_FW_CONFIG address and size through registers to
BL31. This corresponds to SPMC manifest load address and size. The SPMC
manifest is mapped in BL31 by dynamic mapping. This patch removes BL2
changes from generic code (which were enclosed by SPD=spmd) and retrieves
SPMC manifest size directly from within SPMD. The SPMC manifest load
address is still passed through a register by generic code.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I35c5abd95c616ae25677302f0b1d0c45c51c042f

As a follow-up to bdd2596d

, and related to SPM Dispatcher
EL3 component and SPM Core S-EL2/S-EL1 component: update
with cosmetic and coding rules changes. In addition:
-Add Armv8.4-SecEL2 arch detection helper.
-Add an SPMC context (on current core) get helper.
-Return more meaningful error return codes.
-Remove complexity in few spmd_smc_handler switch-cases.
-Remove unused defines and structures from spmd_private.h
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I99e642450b0dafb19d3218a2f0e2d3107e8ca3fe

Change-Id: I5daa3f2b4b9d85cb857547a588571a9aa8ad05c2
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>

Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Change-Id: Ic1a392a633b447935fa3a7528326c97845f5b1bc

Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Change-Id: Iabeaee35c22608c93945c8295bf70947b0f6049a

The platform io policies array is now always accessed through a fconf getter.
This gives us an ideal spot to check for out-of-bound accesses.

Remove the assertion in plat_get_image_source(), which is now redundant.

Change-Id: Iefe808d530229073b68cbd164d927b8b6662a217
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Moved SMCCC defines from plat_arm.h to new <smccc_def.h> header
and include this header in all ARM platforms.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I4cbc69c7b9307461de87b7c7bf200dd9b810e485

This patch provides support for measured boot by adding calculation
of BL2 image hash in BL1 and writing these data in TB_FW_CONFIG DTB.

Change-Id: Ic074a7ed19b14956719c271c805b35d147b7cec1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Implemented SMCCC_ARCH_SOC_ID call in order to get below
SOC information:

1. SOC revision
2. SOC version

Implementation done using below SMCCC specification document:
https://developer.arm.com/docs/den0028/c

Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ie0595f1c345a6429a6fb4a7f05534a0ca9c9a48b

Necessary infrastructure added to integrate fconf framework in BL31 & SP_MIN.
Created few populator() functions which parse HW_CONFIG device tree
and registered them with fconf framework. Many of the changes are
only applicable for fvp platform.

This patch:
1. Adds necessary symbols and sections in BL31, SP_MIN linker script
2. Adds necessary memory map entry for translation in BL31, SP_MIN
3. Creates an abstraction layer for hardware configuration based on
   fconf framework
4. Adds necessary changes to build flow (makefiles)
5. Minimal callback to read hw_config dtb for capturing properties
   related to GIC(interrupt-controller node)
6. updates the fconf documentation

Change-Id: Ib6292071f674ef093962b9e8ba0d322b7bf919af
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

TBBR spec advocates for optional encryption of firmwares (see optional
requirement: R060_TBBR_FUNCTION). So add an IO abstaction layer to
support firmware decryption that can be stacked above any underlying IO/
packaging layer like FIP etc. It aims to provide a framework to load any
encrypted IO payload.

Also, add plat_get_enc_key_info() to be implemented in a platform
specific manner as handling of encryption key may vary from one platform
to another.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Change-Id: I9892e0ddf00ebecb8981301dbfa41ea23e078b03

Add framework for autheticated decryption of data. Currently this
patch optionally imports mbedtls library as a backend if build option
"DECRYPTION_SUPPORT = aes_gcm" is set to perform authenticated decryption
using AES-GCM algorithm.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Change-Id: I2966f0e79033151012bf4ffc66f484cd949e7271

This patch implements loading of Secure Partition packages using
existing framework of loading other bl images.

The current framework uses a statically defined array to store all the
possible image types and at run time generates a link list and traverse
through it to load different images.

To load SPs, a new array of fixed size is introduced which will be
dynamically populated based on number of SPs available in the system
and it will be appended to the loadable images list.

Change-Id: I8309f63595f2a71b28a73b922d20ccba9c4f6ae4
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

Use the firmware configuration framework to retrieve information about
Secure Partitions to facilitate loading them into memory.

To load a SP image we need UUID look-up into FIP and the load address
where it needs to be loaded in memory.

This patch introduces a SP populator function which gets UUID and load
address from firmware config device tree and updates its C data
structure.

Change-Id: I17faec41803df9a76712dcc8b67cadb1c9daf8cd
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

This patch introduces a build flag which allows the xlat tables
to be mapped in a read-only region within BL31 memory. It makes it
much harder for someone who has acquired the ability to write to
arbitrary secure memory addresses to gain control of the
translation tables.

The memory attributes of the descriptors describing the tables
themselves are changed to read-only secure data. This change
happens at the end of BL31 runtime setup. Until this point, the
tables have read-write permissions. This gives a window of
opportunity for changes to be made to the tables with the MMU on
(e.g. reclaiming init code). No changes can be made to the tables
with the MMU turned on from this point onwards. This change is also
enabled for sp_min and tspd.

To make all this possible, the base table was moved to .rodata. The
penalty we pay is that now .rodata must be aligned to the size of
the base table (512B alignment). Still, this is better than putting
the base table with the higher level tables in the xlat_table
section, as that would cost us a full 4KB page.

Changing the tables from read-write to read-only cannot be done with
the MMU on, as the break-before-make sequence would invalidate the
descriptor which resolves the level 3 page table where that very
descriptor is located. This would make the translation required for
writing the changes impossible, generating an MMU fault.

The caches are also flushed.
Signed-off-by: Petre-Ionut Tudor <petre-ionut.tudor@arm.com>
Change-Id: Ibe5de307e6dc94c67d6186139ac3973516430466

The cookie will be leveraged in the next commit.

Change-Id: Ie8bad275d856d84c27466461cf815529dd860446
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

For platforms that have two or more TZC400 controllers instantiated,
allow the TZC400 driver to be usable with all those instances.
This is achieved by allowing 'arm_tzc400_setup' function to accept
the base address of the TZC400 controller.

Change-Id: I4add470e6ddb58432cd066145e644112400ab924
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>

The base address for second DRAM varies across different platforms.
So allow platforms to define second DRAM by moving Juno/SGM-775 specific
definition of second DRAM base address to Juno/SGM-775 board definition
respectively, SGI/RD specific definition of DRAM 2 base address to SGI
board definition.

Change-Id: I0ecd3a2bd600b6c7019c7f06f8c452952bd07cae
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>

A TZC400 can have upto 4 filters and the number of filters instantiated
within a TZC400 is platform dependent. So allow platforms to define the
value of PLAT_ARM_TZC_FILTERS by moving the existing Juno specific
definition of PLAT_ARM_TZC_FILTERS to Juno board definitions.

Change-Id: I67a63d7336595bbfdce3163f9a9473e15e266f40
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>

This patch reserves and maps the Trusted DRAM for SPM core execution.
It also configures the TrustZone address space controller to run BL31
in secure DRAM.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I7e1bb3bbc61a0fec6a9cb595964ff553620c21dc

This patch repurposes the TOS FW configuration file as the manifest for
the SPM core component which will reside at the secure EL adjacent to
EL3. The SPM dispatcher component will use the manifest to determine how
the core component must be initialised. Routines and data structure to
parse the manifest have also been added.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: Id94f8ece43b4e05609f0a1d364708a912f6203cb

On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.

Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Multi-chip platforms have two or more identical chips connected using a
high speed coherent link. In order to identify such platforms,
add chip_id and multi_chip_mode information in the platform variant
info structure. The values of these two new elements is populated
during boot.

Change-Id: Ie6e89cb33b3f0f408814f6239cd06647053e23ed
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

Currently, an IO setup failure will be ignored on arm platform release
build. Change this to panic instead.

Change-Id: I027a045bce2422b0a0fc4ff9e9d4c6e7bf5d2f98
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Change the return type of "arm_io_is_toc_valid()" and
"plat_arm_bl1_fwu_needed()" to bool, to match function behavior.

Change-Id: I503fba211219a241cb263149ef36ca14e3362a1c
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Use the firmware configuration framework to store the io_policies
information inside the configuration device tree instead of the static
structure in the code base.

The io_policies required by BL1 can't be inside the dtb, as this one is
loaded by BL1, and only available at BL2.

This change currently only applies to FVP platform.

Change-Id: Ic9c1ac3931a4a136aa36f7f58f66d3764c1bfca1
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Use the firmware configuration framework in arm dynamic configuration
to retrieve mbedtls heap information between bl1 and bl2.

For this, a new fconf getter is added to expose the device tree base
address and size.

Change-Id: Ifa5ac9366ae100e2cdd1f4c8e85fc591b170f4b6
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Use fconf to retrieve the `disable_authentication` property.
Move this access from arm dynamic configuration to bl common.

Change-Id: Ibf184a5c6245d04839222f5457cf5e651f252b86
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

This patch introduces a better separation between the trusted-boot
related properties, and the dynamic configuration DTBs loading
information.

The dynamic configuration DTBs properties are moved to a new node:
`dtb-registry`. All the sub-nodes present will be provided to the
dynamic config framework to be loaded. The node currently only contains
the already defined configuration DTBs, but can be extended for future
features if necessary.
The dynamic config framework is modified to use the abstraction provided
by the fconf framework, instead of directly accessing the DTBs.

The trusted-boot properties are kept under the "arm,tb_fw" compatible
string, but in a separate `tb_fw-config` node.
The `tb_fw-config` property of the `dtb-registry` node simply points
to the load address of `fw_config`, as the `tb_fw-config` is currently
part of the same DTB.

Change-Id: Iceb6c4c2cb92b692b6e28dbdc9fb060f1c46de82
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Move the loading of the dtb from arm_dym_cfg to fconf. The new loading
function is not associated to arm platform anymore, and can be moved
to bl_main if wanted.

Change-Id: I847d07eaba36d31d9d3ed9eba8e58666ea1ba563
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Enables usage of ARM_ROTPK_LOCATION=regs for FVP board.
Removes hard-coded developer keys. Instead, setting
ARM_ROTPK_LOCATION=devel_* takes keys from default directory.
In case of ROT_KEY specified - generates a new hash and replaces the
original.

Note: Juno board was tested by original feature author and was not tested
for this patch since we don't have access to the private key. Juno
implementation was moved to board-specific file without changing
functionality. It is not known whether byte-swapping is still needed
for this platform.

Change-Id: I0fdbaca0415cdcd78f3a388551c2e478c01ed986
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>

In order to support SEPARATE_NOBITS_REGION for Arm platforms, we need to load
BL31 PROGBITS into secure DRAM space and BL31 NOBITS into SRAM. Hence mandate
the build to require that ARM_BL31_IN_DRAM is enabled as well.

Naturally with SEPARATE_NOBITS_REGION enabled, the BL31 initialization code
cannot be reclaimed to be used for runtime data such as secondary cpu stacks.

Memory map for BL31 NOBITS region also has to be created.

Change-Id: Ibbc8c9499a32e63fd0957a6e254608fbf6fa90c9
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

This reverts commit d433bbdd.

Change-Id: I46c69dce704a1ce1b50452dd4d62425c4a67f7f0

In order to support SEPARATE_NOBITS_REGION for Arm platforms, we need to load
BL31 PROGBITS into secure DRAM space and BL31 NOBITS into SRAM. Hence mandate
the build to require that ARM_BL31_IN_DRAM is enabled as well.

Naturally with SEPARATE_NOBITS_REGION enabled, the BL31 initialization code
cannot be reclaimed to be used for runtime data such as secondary cpu stacks.

Memory map for BL31 NOBITS region also has to be created.

Change-Id: Ibd480f82c1dc74e9cbb54eec07d7a8fecbf25433
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

Implements a way to add platform specific power off code to a
Marvell Armada 8K platform.

Marvell Armada 8K boards can now add a board/system_power.c file
that contains a system_power_off() function.
This function can now send a command to a power management MCU or
other board periferals before shutting the board down.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Change-Id: Iaba20bc2f603195679c54ad12c0c18962dd8e3db
---
I am working on a device that will be ported later, which has a
custom power management MCU that handles LEDs, board power and fans
and requires this separation.