GitLab

Clock enable EEMI API is reimplemented to use system-level clock
and pll EEMI APIs rather than direct MMIO read/write accesses to clock
and pll control registers.
Since linux still uses clock enable API to trigger locking of the PLLs
in the pm_clock_enable() implementation we need to workaround this by
distinguishing two cases: 1) if the given clock ID corresponds to a PLL
output clock ID; or 2) given clock ID is truly an on-chip clock that can
be gated.
For case 1) we'll call pm_api_clock_pll_enable() implemented in
pm_api_clock.h/c. This function checks what is the buffered PLL mode and
calls the system-level PLL set mode EEMI API with the buffered mode value
specified as argument. Long term, if linux driver get fixed to use PLL
EEMI API to control PLLs, this case could be removed from ATF.
For case 2) we'll call the PMU to configure the clock gate. This is done
using system-level clock enable EEMI API.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>

When linux calls pm_ioctl_get_pll_frac_mode() it doesn't expect the actual
mode to be read from hardware, but the value that it is intending to
program. Therefore, we return the buffered value to linux.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>

When linux calls pm_ioctl_set_pll_frac_mode() it doesn't expect the
fractional mode to be changed in hardware. Furthermore, even before this
patch setting the mode which is done by writing into register takes
no effect until the PLL reset is deasserted, i.e. until linux "enables"
the PLL. To adjust the code to system-level PLL EEMI API and avoid
unnecessary IPIs that would otherwise be issued, we buffer the mode
value set via IOCTL until the PLL mode really needs to be set.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>

Fractional data should be set using PLL set parameter EEMI API. This
stands for system-level communication (APU to PMU). Since linux
already uses a specific IOCTL function to do this and we need to
keep it that way, the pll clock ID given by linux has to be mapped
to the pll node ID that is communicated at the system-level (argument
of PLL set parameter API).
With this modification the function pm_api_clk_set_pll_frac_data is
removed from pm_api_clock.c/h because it became unused.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>

Fractional data should be get using PLL get parameter EEMI API. This
stands for system-level communication (APU to PMU). Since linux
already uses a specific IOCTL function to do this and we need to
keep it that way, the pll clock ID given by linux has to be mapped
to the pll node ID that is communicated at the system-level (argument
of PLL get parameter API).
With this modification the function pm_api_clk_get_pll_frac_data is
removed from pm_api_clock.c/h because it became unused.
The clock enum is defined as 'enum clock_id'.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>

This API will be used to get the currently configured PLL mode:
reset (bypassed and unlocked), integer or fractional (locked).
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>

This API will be used to set the PLL mode: reset (unlocked), integer
or fractional (locked). If reset mode is set the PM controller will
bypass the target PLL prior to asserting the reset. If integer or
fractional mode is set the PM controller will program and trigger
locking of the PLL. If success status is returned the PLL is locked
and its bypass is deasserted. If fractional mode is set the fractional
divider (data parameter) has to have a non-zero value prior to issuing
pll set fractional mode. The caller need to ensure that the data
parameter is properly set using pll get/set parameter EEMI API.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>

This API will be used to get a parameter for the PLL. Parameter values
represent the values as defined in the Zynq MPSoC register reference
manual ug1087.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>

This API will be used to set a parameter for the PLL. The parameter
value that is set will have effect once the PLL mode is set to integer
or fractional mode. Parameter values represent the values as defined
in the Zynq MPSoC register reference manual ug1087.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This function is not related to Arm platforms and can be reused by other
platforms if needed.

Change-Id: Ia9c328ce57ce7e917b825a9e09a42b0abb1a53e8
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

There are several platforms using arm_setup_page_tables(), which is
supposed to be Arm platform only. This creates several dependency
problems between platforms.

This patch adds the definition XLAT_TABLES_LIB_V2 to the xlat tables lib
v2 makefile. This way it is possible to detect from C code which version
is being used and include the correct header.

The file arm_xlat_tables.h has been renamed to xlat_tables_compat.h and
moved to a common folder. This way, when in doubt, this header can be
used to guarantee compatibility, as it includes the correct header based
on XLAT_TABLES_LIB_V2.

This patch also removes the usage of ARM_XLAT_TABLES_V1 from QEMU (so
that is now locked in xlat lib v2) and ZynqMP (where it was added as a
workaround).

Change-Id: Ie1e22a23b44c549603d1402a237a70d0120d3e04
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Non-Arm platforms shouldn't use Arm platform code. This patch copies the
implementation of the functions in arm_helpers.S to zynqmp_helpers.S to
remove this dependency of zynqmp on Arm platforms.

Change-Id: Ia85f303c4c63bcf0ffa57c7f3ef9d88376729b6b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The "Secure" prefix (S-ELx) is valid only for S-EL0 and S-EL1 but is
meaningless for EL3, since EL3 is always secure. Hence, the "S" prefix
has been removed from wherever it was used as "S-EL3".

Change-Id: Icdeac9506d763f9f83d7297c7113aec7b85e9dbe
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

- Remove references to removed build options.
- Migrate to bl31_early_platform_setup2().

Change-Id: Ibeb8982a0a841f55ce778c4f09f06b72b47b21d8
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Ensure case clauses:
*   Terminate with an unconditional break, return or goto statement.
*   Use conditional break, return or goto statements as long as the end
    of the case clause is unreachable; such case clauses must terminate
    with assert(0) /* Unreachable */ or an unconditional  __dead2 function
    call
*   Only fallthough when doing otherwise would result in less
    readable/maintainable code; such case clauses must terminate with a
    /* Fallthrough */ comment to make it clear this is the case and
    indicate that a fallthrough is intended.

This reduces the chance of bugs appearing due to unintended flow through a
switch statement

Change-Id: I70fc2d1f4fd679042397dec12fd1982976646168
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Enable ARM_XLAT_TABLES_LIB_V1 as ZynqMP is using
v1 library of translation tables.

With upstream patch d323af9e

,
the usage of MAP_REGION_FLAT is referring to definition in file
include/lib/xlat_tables/xlat_tables_v2.h but while preparing
xlat tables in lib/xlat_tables/xlat_tables_common.c it is referring
to include/lib/xlat_tables/xlat_tables.h which is v1 xlat tables.
Also, ZynqMP was using v1 so defined ARM_XLAT_TABLES_LIB_V1 to
use v1 xlat tables everywhere.
This fixes the issue of xlat tables failures as it takes v2
library mmap_region structure in some files and v1 in other
files.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

This patch adds ATF support for AES data blob encrypt/decrypt.
ATF establishes a path to send the address of the structure
to the xilsecure, so that it will pick addresses of the data
and performs the requested operation (encrypt/decrypt) and puts
the result in load address.

where structure contains
- Data blob src address
- load address
- IV address
- Key address - this will actual key addr in case of KUP
		else it will be zero.
- Data-size
- Aes-op type
- KeySrc
Signed-off-by: Kalyani Akula <kalyani.akula@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

This patch removes support for emulation platforms
EP108 and Veloce.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Correct function header of pm_api_clock_getparent() and
pm_api_clock_setparent().
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Acked-by: Will Wong <WILLW@xilinx.com>

PLL type clock is enabled by FSBL on boot-up. PMUFW enable/disable
them based on their user count. So, it should not be handled from ATF.

Put PLL type clock into bypass and reset mode only while changing
PLL rate (FBDIV).
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

This patch adds new API's for performing pl configuration
readback.
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

CCF has already provision to enable clock during registration
through CLK_IS_CRITICAL flag. Use CLK_IS_CRITICAL instead of
init_enable attribute.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Jolly Shah <jolly.shah@xilinx.com>

WDT used by APU is FPD_WDT. FPD WDT clock is controlled by
FPD_SLCR.WDT_CLK_SEL register. Correct the same in WDT clock
database.

As per FPD_SLCR.WDT_CLK_SEL register, there can be only two
parents of WDT clock not three. Fix the same by correcting it's
parents in clock database.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Jolly Shah <jolly.shah@xilinx.com>

Add support for writing to AFI registers.
So that after writing a bitstream the interface can be programmed.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Since the MMIO read/write APIs are removed from Linux user space,
Linux cannot directly write to the Global General Storage Register 4
any more to set healthy boot status.

Create an IOCTL to allow Linux to set boot health status.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Will Wong <willw@xilinx.com>

To make ULPI transceiver work, a HIGH - LOW - HIGH pulse needs
to be given to resetb pin of ULPI chip. In ZYNQMP, this resetb
pin is being driven by BOOT MODE PIN 1. The BOOT MODE PIN's
are controlled by BOOT_PIN_CTRL register present in CRL_APB
address region. Since CRL_APB can be resticted to secure access,
this pin should be controlled by ATF.

This patch adds the support for the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Currently in Linux maximum number of clocks is hard-coded and
so it needs to allocate static memory. It can get actual clock
number after querying all clock names by special clock name
string. Add new query data parameter to get actual number of
clocks so Linux can get actual clock numbers in advance.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>

Change arm_setup_page_tables() to take a variable number of memory
regions. Remove coherent memory region from BL1, BL2 and BL2U as
their coherent memory region doesn't contain anything and
therefore has a size of 0. Add check to ensure this
doesn't change without us knowing.

Change-Id: I790054e3b20b056dda1043a4a67bd7ac2d6a3bc0
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Also change header guards to fix defects of MISRA C-2012 Rule 21.1.

Change-Id: Ied0d4b0e557ef6119ab669d106d2ac5d99620c57
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch reads the chipid registers directly instead of making
pm call when running at BL32. User should ensure that these registers
should always be accessed from APU in their system configuration.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

This patch builds ATF to DDR if SPD is enabled as it cant fit in
On chip memory(OCM) with SPD enabled. This solves the issue
of build failure with SPD enabled for ZynqMP platform.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

RFC4122 defines that fields are stored in network order (big endian),
but TF-A stores them in machine order (little endian by default in TF-A).
We cannot change the future UUIDs that are already generated, but we can store
all the bytes using arrays and modify fiptool to generate the UUIDs with
the correct byte order.

Change-Id: I97be2d3168d91f4dee7ccfafc533ea55ff33e46f
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch adds support to restart system incase of wdt
timeout.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

The vcu disable bit in efuse ipdisable register is valid
only if PL powered up so, consider PL powerup status for
determing EG/EV part. If PL is not powered up, display
EG/EV as a part of string. The PL powerup status will
be filled by pmufw based on PL PROGB status in the
9th bit of version field.This patch also used IPI
to get this info from pmufw instead of directly accessing
the registers. Accessing this info from pmufw using
IPI fixes the issue of PMUFW access denied error for
reading IPDISABLE register.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

This patch adds new API for processing secure images. This API
is used for authentication and decryption of secure images using
xilsecure in pmufw.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

Existing code blocks each IPI send request in ipi_mb_notify()
function till pmu clears respective bit in ipi observation
register.

After sending PM_SYSTEM_SHUTDOWN request to PMU, PMU will
restart APU. While PMU is restarting APU, ATF is running out
of OCM, which can cause read/write hang from/to OCM.
There is no need to wait for notification from PMU in case
of SystemShutdown request in ATF, as APU is going to restart.

This patch fixes APU only restart issue.
Signed-off-by: Tejas Patel <tejasp@xilinx.com>
Acked-by: Wendy Liang <wendy.liang@xilinx.com>

This patch makes bitstream load blocking call and waits until
bitstream is loaded successfully or return with error.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Avesh Khan <aveshk@xilinx.com>

GET_CALLBACK_DATA function is not required now. IPI mailbox
can be used instead of GET_CALLBACK_DATA function.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

PMU IPI-1 is used for callbacks from PMU to master. Unsecure
master can also receive callbacks from PMU, so make PMU IPI-1
as non-secure.

All requests from master(s) to PMU would still go on PMU IPI-1
secure channel.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>