GitLab

The CatB erratum ARM_ERRATA_A53_1530924 applies to all TI A53
platforms as well.

See the following for further information:
https://developer.arm.com/documentation/epm048406/2100

Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: Ic095424ce510139e060b38cfb84509d2cc573cad

add mt6359p rtc power off sequence and enable k_eosc mode
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.com>
Change-Id: I65450c63c44ccb5082541dbbe28b8aa0a95ecc56

CID 364146: Control flow issues (DEADCODE)

Since the value of PSTATE_PWR_LVL_MASK and the value the of PLAT_MAX_PWR_LVL
are equal on mt8192, the following equation never hold.

if (aff_lvl > PLAT_MAX_PWR_LVL) {
	return PSCI_E_INVALID_PARAMS;
}

Remove the deadcode to comply with MISRA standard.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I71d0aa826eded8c3b5af961e733167ae40699398

CID 364144: Integer handling issues (NO_EFFECT)

The unsigned value is always greater-than-or-equal-to-zero.
Remove such check.

Change-Id: Ia395eb32f55a7098d2581ce7f548b7e1112beaa0
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>

1 Add Domain1(PCIe device) protect address: 0x80000000~0x83FF0000.
2 Add Domain2(SSPM/SPM/DPM/MCUPM) protect address: 0x40000000~0x1FFFF0000.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I4aaed37150076ae5943484c4adadac999a3d1762

RD-N2 platform has been updated to use six GIC ITS blocks. This results
in change in base address of the GIC Redistributor to accomodate two
new GIC ITS blocks. Update the base address of GICR to reflect the same.
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Change-Id: I740a547328fb9a9f25d7a09c08e61bdbc8bf781c

Functions are reimplemented to issue system-level pinctrl EEMI calls
to the PMU-FW rather than using MMIO read/write. Macros and functions
that appear to be unused after the change is made are removed.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I51f2285a79f202cb2ca9f031044002e16dd1e92f

Functions are reimplemented to issue system-level pinctrl EEMI calls
to the PMU-FW rather than using MMIO read/write. Macros and functions
that appear to be unused after the change is made are removed.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I21b8fda855aa69090b85d6aaf411e19560201cb5

The calls are just passed through to the PMU-FW. Before issuing
other pinctrl functions the pin should be successfully requested.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Ibce280edebedf779b3962009c274d0b3d928e0e4

In pm_query_data() function return type is stored in response so
there is no use of return type. Update return type of function
pm_query_data() from enum pm_ret_status to void. Similarly
update return type of pm_api_clock_get_name() and
pm_api_pinctrl_get_function_name() functions.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Id811926f0b4ebcc472480bb94f3b88109eb036cd

This patch adds support to enable OP-TEE as S-EL1 SP with SPMC at S-EL2
     - create SPMC manifest file with OP-TEE as SP
     - add support for ARM_SPMC_MANIFEST_DTS build option
     - add optee entry with ffa as method in tc0.dts
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Change-Id: Ia9b5c22c6f605d3886914bbac8ac45e8365671cb

Enable SPD=opteed support for tc0 platform.
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Change-Id: Ieb038d645c68fbe6b5a211c7279569e21b476fc3

RSB is faster and more efficient, and it has a simpler driver. As long
as the PMIC is returned to I2C mode after use, the rich OS can later use
either bus.

Change-Id: I0c5f32e88a090c8c5cccb81bd24596b301ab9da7
Signed-off-by: Samuel Holland <samuel@sholland.org>

This gives the rich OS the flexibility to choose between I2C and RSB
communication. Since a runtime address can only be assigned once after
entering RSB mode, it also lets the rich OS choose any runtime address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Id49c124c5e925985fc31c0ba38c7fb6c941aafa8

None of the other drivers (Linux, U-Boot, Crust) need to lower the bus
clock frequency to switch the PMIC to RSB mode. That logic is not needed
here, either. The hardware takes care of running this transaction at the
correct bus frequency.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Idcfe933df4da75d5fd5a4f3e362da40ac26bdad1

BL31 reports the following warning during boot:

  WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing!

Resolve this by enabling the workaround on the affected platforms.

Change-Id: Ia1d5075370be5ae67b7bece96ec0069d9692b14c
Signed-off-by: Samuel Holland <samuel@sholland.org>

While the Allwinner platform code nominally supported a custom
PRELOADED_BL33_BASE, some references to the BL33 load address used
another constant: PLAT_SUNXI_NS_IMAGE_OFFSET. To allow the DTB search
code to work if a U-Boot BL33 is loaded to a custom address,
consistently use PRELOADED_BL33_BASE. And to avoid this confusion in
the future, remove the other constant.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie6b97ae1fdec95d784676aef39200bef161471b0

The H6 has a "secure port controller" similar to the A64/H5, but with
more ports and a different register layout. Split the platform-specific
parts out into a header, and add the missing MMIO base address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I3703868bc595459ecf9568b9d1605cb1be014bf5

H6 has a reorganized R_PRCM compared to A64/H5, with the security switch
at a different offset. Until now, we did not notice, because the switch
has no effect unless the secure mode e-fuse is blown.

Since we are adding more platform-specific CCU registers, move them to
their own header, and out of the memory map (where they do not belong).
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie77476db0515080954eaa2e32bf6c3de657cda86

Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Icef550072296d6aba89a0827dd72d0b86047556f

Add the initial board support for RD-N2 platform.

Change-Id: I8325885bf248dd92191d6fc92a2da91c23118f8c
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Upcoming RD platforms will have an updated memory map for the various
pheripherals on the system. So, for the newer platforms, handle the
memory mapping and other platform specific functionality separately
from the existing platforms.

Change-Id: Iab1355a4c8ea1f6db4f79fcdd6eed907903b6a18
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

In preparation for adding the board support for RD-N2 platform, add
macros to define the platform id and the corresponding SCMI platform
info for the RD-N2 platform.

Change-Id: Ie764ae618732b39e316f7ed080421f5d79adab21
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Upcoming RD platforms have changes in the SOC address map from that
of the existing platforms. As a prepartory step to add support for the
upcoming platforms, create platform definitions for those platforms.

Change-Id: Ic5df9fed02c44e65ec260bbb5efc1b8dbd919a56
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Upcoming RD platforms have deviations in various definitions of
platform macros from that of the exisiting platforms. In preparation
for adding support for those upcoming RD platforms, refactor the
header file inclusion to allow newer platforms to use a different
set of platform macros.

Change-Id: Ic80283ddadafaa7f766f300652cb0d4e507efdb6
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Upcoming RD platforms have a different memory map from those of the
existing platforms. So make the build of the existing mmap entries to be
usable only for existing platforms and let upcoming platforms define
a different set of mmap entries.

Change-Id: Id1ef0293efe8749c78a99237e78d32573c7233aa
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Current implementation doesn't support change of div1 value if clk
has 2 divisor because div1 clk is the parent of the div2 clk and div2
clk does not have SET_RATE_PARENT flag.
This causes div1 value to be fixed and only value of div2 will be
adjusted according to required clock rate.

Example:
 Consider a case of nand_ref clock which has 2 divisor and 1 mux.
 The frequency of mux clock is 1500MHz and default value of div1 and
 div2 is 15 and 1 respectively. So the final clock will be of 100MHz.
 When driver requests 80MHz for nand_ref clock, clock framework will
 adjust the div2 value to 1 (setting div2 value 2 results final clock
 to 50MHz which is more inaccurate compare to 100Mhz) which results
 final clock to 100MHz.
 Ideally the value of div1 and div2 should be updated to 19 and 1
 respectively so that final clock goes to around 78MHz.

This patch fixes above problem by allowing change in div1 value.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Ibb98f6748d28653fdd1e59bf433b6a37ce9c1a58

This patches copies only the valid part of string and
avoids filling junk at the end.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: If23772f31f9cf7f5042e8bfc474fbfe77dcd90e7

The primary VM concept is removed from the SPMC.
Update the SPMC manifests with number of Execution Contexts
and SP workspace size for the first Secure Partition (as it
is done for NWd secondary VMs and other SPs).
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I3b9c52666f7dfe74ab1f7d2148ad0070ee44b54e

The chosen node is no longer required as the SPMC implements
a specific boot flow which no longer requires this node.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Ib566b602a7f83003a1b2d0ba5f6ebf4d8b7a9156

Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I0981c43e2ef8172138f65d95eac7b20f8969394e

The PVM concept is removed from the SPMC so the device-memory
node which is specifying the device memory range for the PVM
is no longer applicable.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: If0cb956e0197028b24ecb78952c66ec454904516

1. Add mcusys related dcm drivers
2. Turn on mcusys-related dcm by default

Change-Id: Ibbee37c87cc38e7a6cd7c93c2fc0817aad6dbe95
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>

enable PTP3 for protecting sysPi
Signed-off-by: elly.chiang <elly.chiang@mediatek.com>
Change-Id: Ic3a13c8314f829dca8547861b98639d1d9444eb2

Add the basic SiP service

Change-Id: Ib7f2380aab910adf8d33498a79ecd287273907c5
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>

When system resume, we want to print log as soon as possible.
So we add uart save and restore api, and they will be called
when systtem suspend and resume.

Change-Id: I83b477fd2b39567c9c6b70534ef186993f7053ae
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.com>
Signed-off-by: Roger Lu <roger.lu@mediatek.com>

1.Modify this driver to make it more complete and more standard.
2.And makes this driver available for more IC services.
3.Solve some bugs in the software.
Signed-off-by: G.Pangao <gtk_pangao@mediatek.com>
Change-Id: I284956d47ebbbd550ec93767679181185e442348

add power-off support
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: If19e99971515a8ae1ac9ae21046e4382adc18a69

add pmic mt6359p driver
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I20f2218f7d2087e8d2bf31258cf92a02e0dab77d

Init delay_timer for the use of delay functions

Change-Id: I35aefd7515bb9259634c8b6bc37d8c74da96e8f1
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>