GitLab

This patch enable the Memory Controller's "Coalescer" feature to
improve performance of memory transactions.

Change-Id: I50ba0354116284f85d9e170c293ce77e9f3fb4d8
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>

This patch changes SCRATCH_BOOT_PARAMS_ADDR macro to use SECURE_SCRATCH_RSV81
instead of SECURE_SCRATCH_RSV44. The previous level bootloader changed this
setting, so update here to keep both components in sync.

Change-Id: I4e0c1b54fc69482d5513a8608d0bf616677e1bdd
Signed-off-by: steven kao <skao@nvidia.com>

This patch implements the PSCI system shutdown and reset handlers,
that in turn issue the MCE commands.

Change-Id: Ia9c831674d7be615a6e336abca42f397e4455572
Signed-off-by: Vignesh Radhakrishnan <vigneshr@nvidia.com>

This patch adds support for shutdown/reboot handlers to the MCE
driver.

ATF communicates with mce using nvg interface for shutdown &
reboot. Both shutdown and reboot use the same nvg index.
However, the 1st bit of the nvg data argument differentiates
whether its a shutdown or reboot.

Change-Id: Id2d1b0c4fec55abf69b7f8adb65ca70bfa920e73
Signed-off-by: Vignesh Radhakrishnan <vigneshr@nvidia.com>

Currently firmware seems to be checking if we can get into system
suspend after checking if CC6 & C7 is allowed. For system suspend
to be triggered, the firmware needs to request for CG7 as well.

This patch fixes this anomaly.

Change-Id: I39c4c50092a4288f4f3fa4b0b1d5026be50f058f
Signed-off-by: Vignesh Radhakrishnan <vigneshr@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a new configuration option to the platform makefiles
that disables/enables strict checking mode. The config is enabled
by default.

Change-Id: I727dd0facee88d9517bf6956eaf9163eba25c8bb
Signed-off-by: Steven Kao <skao@nvidia.com>

This patch cleans the makefile to remove unused platform config
options.

Change-Id: I96d9795c0f0ba593de96017dc9a401d7c2ab471a
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The stream IDs for XUSB programmed during cold boot are lost on System
Suspend. This patch restores the XUSB stream IDs on System Resume.

NOTE: THE WARMBOOT CODE NEEDS TO MAKE SURE THAT THE XUSB MODULE IS OUT
OF RESET AND THE CLOCKS ARE ENABLED, BEFORE POWERING ON THE CPU, DURING
SYSTEM RESUME.

Change-Id: Ibd5f1e5ebacffa6b29b625f4c41ecf204afa8191
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

UEFI decompression will fail if the payload size is too large and the load
address is too low. This patch moves the payload to a higher address to fix
the issue
Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>
Change-Id: I36087fbd2237b62891c59dbe2d34336bddfaa396

All function in socfpga_sip_svc.c should only be called locally except
sip_smc_handler().
Signed-off-by: Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: Ib84ef9a2e521967baa4cfd32e6bc569dd3a5d2f5

Now that there is plenty of space (32 KiB) available for NOBITS
sections, we can afford using an entire page for coherent memory. In
fact, because it simplifies the code, this is a beneficial change for
loaded image (.text) size, where we are still close to the size limit.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I0b899dabcb162015c63b0e4aed0869569c889ed9

Implements a way to add platform specific power off code to a
Marvell Armada 8K platform.

Marvell Armada 8K boards can now add a board/system_power.c file
that contains a system_power_off() function.
This function can now send a command to a power management MCU or
other board periferals before shutting the board down.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Change-Id: Iaba20bc2f603195679c54ad12c0c18962dd8e3db
---
I am working on a device that will be ported later, which has a
custom power management MCU that handles LEDs, board power and fans
and requires this separation.

Add missing #address-cells and #size-cells into generated DT, otherwise
the DT is invalid. While the parsers thus far handled this correctly via
various fallbacks, this is not applicable in the long run, so fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Ic808a3b27b93e5258ec1a19acc3d593e53625c15

This patch removes un-needed r/w parameter checks for qspi driver. The
driver can actually access any offset and size.
Signed-off-by: Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: If60b2c016aa91e2c24ddc57c6ad410c8dc5dcf53

This patch fixes the violations of Rule 21.1 from all the
header files.

Rule 21.1 "#define and #undef shall not be used on a reserved
           identifier or reserved macro name"
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I12e17a5d7158defd33b03416daab3049749905fc

This patch fixes the violations of Rule 21.1 from all the
Tegra common header files.

Rule 21.1 "#define and #undef shall not be used on a reserved
           identifier or reserved macro name"
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I2e117645c110e04c13fa86ebbbb38df4951d2185

NOTE for platform integrators:
   API `plat_psci_stat_get_residency()` third argument
   `last_cpu_idx` is changed from "signed int" to the
   "unsigned int" type.

Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.

2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent

Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.

Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c

This patch removes re-definition of the following FVP build
options from plat\arm\board\fvp\fvp_def.h:
 'FVP_CLUSTER_COUNT'
 'FVP_MAX_CPUS_PER_CLUSTER'
 'FVP_MAX_PE_PER_CPU'
which are set in platform.mk.

This fixes a potential problem when a build option set in
platform.mk file can be re-defined in fvp_def.h header file
used by other build component with a different makefile which
does not set this option.
Ref. GENFW-3505.

Change-Id: I4288629920516acf2c239c7b733f92a0c5a812ff
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Iee7fb43990047b27972e99572ec4b3dc4e5c0423

In further patches, we aim to enable -Wredundant-decls by default.
This rearragement of helper macros is necessary to make Coverity
tool happy as well as making sure there are no redundant function
declarations for PMF related declarations.

Also, PMF related macros were added to provide appropriate function
declarations for helper APIs which capture PSCI statistics.

Change-Id: I36273032dde8fa079ef71235ed3a4629c5bfd981
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

In further patches, we wish to enable -wredundant-decls check as
part of warning flags by default.

Change-Id: I43410d6dbf40361a503c16d94ccf0f4cf29615b7
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

The MCE driver's helper functions were using postive values as error
codes.

This patch updates the functions to return negative values as error
codes instead. Some functions are updated to use the right error code.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I3e2ecc30a6272a357e1a22ec850543fde2a694f6

This patch adds LPD WDT clock node to the pm_clock clocks structure list
so that LPD WDT can be used from Linux.

Also this patch removes the CLK_LPD_LSBUS from invalid clock list to
allow the registration of this clock to CCF framework as it is the
parent of LPD WDT.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: Iea065aa8150eaba4bb4b42bc6be1fd4b7fe7b403

GEM-related clock models were incorrect and are fixed as follows
(documented below for GEM0, but the same holds for any GEM ID):

- CLK_GEM0_REF_UNGATED represents clock that has DIV0/1 divisors and
 the multiplexer controllable in GEM0_REF_CTRL (CRL_APB). The ID of this
 clock is newly introduced in this patch.

- CLK_GEM0_REF models the clock mux that selects the reference clock
 for Tx, i.e. selects CLK_GEM0_REF_UNGATED or external Tx clock. This
 mux is controllable via GEM_CLK_CTRL (IOU_SLCR), bit GEM0_REF_SRC_SEL.
 Note that the routing of external clock to the mux is not modelled
 and is assumed to be configured by the FSBL if required, and not
 changeable at runtime. The ID of this clock is introduced in this patch.

- CLK_GEM0_TX models clock with only a gate that is controlled via
 bit 25 in GEM0_REF_CTRL (CRL_APB). The parent of this clock is
 CLK_GEM0_REF. The clock ID of CLK_GEM0_TX matches the previous ID
 value of CLK_GEM0_REF. This is done in order to fix the clock models
 and incorrect binding without requiring to change device-tree (binding
 of clock IDs to GEM interface).

- CLK_GEM0_RX models clock that has only gate controlled via RX_CLKACT
 bit (26) in GEM0_REF_CTRL (CRL_APB). Parent of this clock is sourced
 from external RGMII PHY (via MIO or EMIO). We do not model the whole
 clock path to the Rx gate, since this is configured by the FSBL and
 never changed at runtime (and there is no mechanism to change the
 path at runtime). The clock ID of CLK_GEM0_RX clock is equal to the
 previous ID value of CLK_GEM0_TX clock. This is done because the TX/RX
 were swapped in device tree, so by fixing the IDs this way there is no
 need for device tree fix.

Rates of the external RX/TX clocks can be specified in device tree if
needed. Right now, that's not necessary because Tx clock is sourced
from an on-chip PLL (via CLK_GEM0_REF_UNGATED/CLK_GEM0_REF), whereas
the Rx clock is sourced from external reference and the driver never
attempts to get/get clock rate (only to enable it). If this changes in
future, ATF clock model doesn't need to be changed. Instead, the clock
rates for gem0_tx_ext and gem0_rx_ext have to be specified in device
tree.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <will.wong@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: I6497d4309e92205c527bd81b3aa932f4474f5b79

This patch renames FPD WDT clock ID from CLK_WDT to CLK_FPD_WDT.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: I4d00a59b1dc54920115a2da55e8a06347fe2231c

Correct the syscnt frequency for ZynqMP QEMU to 65Mhz.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: Ie0137feb9b7e24ed4e5d6cbf81c58ac77bb69214

Add support for zu48dr and zu49dr to the list of zynqmp devices. The
zu48dr and zu49dr are the new RFSoC silicons with id values of 0x7b
and 0x7e.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: I2978f16bb663853951ef8059bf0327f909447f34

This patch adds new RFSoC device ZU39DR to zynqmp
devices list
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: I35735da9e7d7facbde44323c49eac1b714e4909d

The reclaim init code functionality relies on forward reference in the
linker script. The LLVM linker does not process it correctly.

Change-Id: I993aeb9587bfa07af25b60ed823a6a2c5e970c94
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Signed-off-by: Zelalem Aweke <zelalem.aweke@arm.com>

Point boot address to DDR location for booting A5DS FPGA
FIP, Kernel and rootfs are sideloaded to DDR
Also move BL2 to higher address in DDR

Change-Id: Ia2a57a0bda776a1a0a96bcd3cfb5c6cd2cf4dc04
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>

Correct the system, timer and uart frequencies to successfully run
the stack on FPGA
Correct Cortex-A5MPcore to 8 word granularity for Cache writeback

Change-Id: I2c59c26b7dca440791ad39f2297c68ae513da7b6
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>

Pass DT to OpTee OS, so that OpTee OS can extract NSEC RAM layout from the DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: I7d5ebae8d7ab9c70f079e30563d66bbd6a8ac7a4

Now that DDR drivers are mostly cleaned up , move them out of staging.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: I9de63f847a0ef9ac27a79fb0f848c351fd7f4da6

The SCU connects one to four Cortex-A5/Cortex-A9 processors
to the memory system through the AXI interfaces.

The SCU functions are to:
- maintain data cache coherency between the Cortex-A5/Cortex-A9
  processors
- initiate L2 AXI memory accesses
- arbitrate between Cortex-A5/Cortex-A9 processors requesting
  L2 accesses
- manage ACP accesses.

Snoop Control Unit will enable to snoop on other CPUs caches.
This is very important when it comes to synchronizing data between
CPUs. As an example, there is a high chance that data might be
cache'd and other CPUs can't see the change. In such cases,
if snoop control unit is enabled, data is synchoronized immediately
between CPUs and the changes are visible to other CPUs.

This driver provides functionality to enable SCU as well as enabling
user to know the following
- number of CPUs present
- is a particular CPU operating in SMP mode or AMP mode
- data cache size of a particular CPU
- does SCU has ACP port
- is L2CPRESENT

Change-Id: I0d977970154fa60df57caf449200d471f02312a0
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>

So far we have seen two different clock setups for the Raspberry Pi 4
board, with the VPU clock divider being different. This was handled by
reading the divider register and adjusting the base clock rate
accordingly.
Recently a new GPU firmware version appeared that changed the clock rate
*again*, though this time at a higher level, so the VPU rate (and the
apparent PLLC parent clock) did not seem to change, judging by reading
the clock registers.
So rather than playing cat and mouse with the GPU firmware or going
further down the rabbit hole of exploring the whole clock tree, let's
just skip the baud rate programming altogether. This works because the
GPU firmware actually sets up and programs the debug UART already, so
we can just use it.

Pass 0 as the base clock rate to let the console driver skip the setup,
also remove the no longer needed clock code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Change-Id: Ica88a3f3c9c11059357c1e6dd8f7a4d9b1f98fd7

Increase calibration delay to cater for HPS 1st mode and
reduce clear emif delay which takes too long
Signed-off-by: Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I1a50a5d8a6518ba085d853cb636efa07326552b4

Add support for platform specific warm-reset through psci system reset 2.

- system_reset2 implementation that calls for l2 cache reset
- Check for magic number and request for warm reset in bl2
- Create a shared reset manager header file for Agilex and Stratix 10
- Clean up parameter info in plat_get_next_bl_params
Signed-off-by: Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I3fdd9a2711c80d9bd3dc05b81527781d840bd726

Enable access to secure registers by non-secure world through secure
monitor calls
Signed-off-by: Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I80610e08c7cf31f17f47a7597c269131a8de2491

Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ia2f69e26e34462e113bc2cad4dcb923e20b8fb95

This frees up space in SRAM A2 that will be used by the SCP firmware and
SCPI shared memory.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I8ce035257451e2d142666fe0cd045e59d4d57b35