GitLab

Some minor fixes to interrupt-framework-design.md

TBB: rework cert_create tool to follow a data driven approach

Bootargs tzdram base v2

This patch fixes a pair of typos. The security state had been described
as non-secure where it should have been secure.

Change-Id: Ib3f424708a6b8e2084e5447f8507ea4e9c99ee79

This patch fixes the command line used to compile BL31 on
Tegra platforms.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The TZDRAM base on the reference platform has been bumped up due to
some BL2 memory cleanup. Platforms can also use a different TZDRAM
base by setting TZDRAM_BASE=<value> in the build command line.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes the bootargs pointer from the platform params
structure. Instead the bootargs are passed by the BL2 in the
bl32_ep_info struct which is a part of the EL3 params struct.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Tegra210: enable WRAP to INCR burst type conversions

The Memory Select Switch Controller routes any CPU transactions to
the appropriate slave depending on the transaction address. During
system suspend, it loses all config settings and hence the CPU has
to restore them during resume.

This patch restores the controller's settings for enabling WRAP to
INCR burst type conversions on the master ports, for any incoming
requests from the AXI slave ports.

Tested by performing multiple system suspend cycles.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

tlkd: delete 'NEED_BL32' build variable

Remove the 'NEED_BL32' flag from the makefile. TLK compiles using a
completely different build system and is present on the device as a
binary blob. The NEED_BL32 flag does not influence the TLK load/boot
sequence at all. Moreover, it expects that TLK binary be present on
the host before we can compile BL31 support for Tegra.

This patch removes the flag from the makefile and thus decouples both
the build systems.

Tested by booting TLK without the NEED_BL32 flag.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Tegra denver plat support v3

This patch modifies the 'BUILD_PLAT' makefile variable to point to the soc
specific build directory in order to allow each Tegra soc to have its own
build directory. This way we can keep the build outputs separate and can
keep multiple soc specific builds alive at the same time.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch implements support for T132 (Denver CPU) based Tegra
platforms.

The following features have been added:

* SiP calls to switch T132 CPU's AARCH mode
* Complete PSCI support, including 'System Suspend'
* Platform specific MMIO settings
* Locking of CPU vector registers
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Denver is NVIDIA's own custom-designed, 64-bit, dual-core CPU which is
fully ARMv8 architecture compatible.  Each of the two Denver cores
implements a 7-way superscalar microarchitecture (up to 7 concurrent
micro-ops can be executed per clock), and includes a 128KB 4-way L1
instruction cache, a 64KB 4-way L1 data cache, and a 2MB 16-way L2
cache, which services both cores.

Denver implements an innovative process called Dynamic Code Optimization,
which optimizes frequently used software routines at runtime into dense,
highly tuned microcode-equivalent routines. These are stored in a
dedicated, 128MB main-memory-based optimization cache. After being read
into the instruction cache, the optimized micro-ops are executed,
re-fetched and executed from the instruction cache as long as needed and
capacity allows.

Effectively, this reduces the need to re-optimize the software routines.
Instead of using hardware to extract the instruction-level parallelism
(ILP) inherent in the code, Denver extracts the ILP once via software
techniques, and then executes those routines repeatedly, thus amortizing
the cost of ILP extraction over the many execution instances.

Denver also features new low latency power-state transitions, in addition
to extensive power-gating and dynamic voltage and clock scaling based on
workloads.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The validate_power_state() handler checks the power_state for a valid afflvl
and state id. Although the afflvl check is common, the state ids are implementation
defined.

This patch moves the handler to the tegra/soc folder to allow each SoC to validate
the power_state for supported parameters.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch moves the inclusion of CPU code (A53, A57) to T210's
makefile. This way we can reduce code size for Tegra platforms by
including only the required CPU files.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Tegra misc fixes v3

A new config, ENABLE_NS_L2_CPUECTRL_RW_ACCESS, allows Tegra platforms to
enable read/write access to the L2 and CPUECTRL registers. T210 is the
only platform that needs to enable this config for now.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch locks access to the PMC registers which hold the CPU reset
vector addresses. The PMC registers are used by the warmboot code and
must be locked during boot/resume to avoid booting into custom firmware
installed by unknown parties e.g. hackers.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The PMC Scratch22 register contains the CPU reset vector to
be used by the warmboot code to power up the CPU while resuming
from  system suspend. This patch locks this PMC register to avoid
any further writes.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch checks if the target CPU is already online before
proceeding with it's power ON sequence.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch de-asserts the CPU reset signals for each CPU as
part of it's power on sequence. This is needed to get rid of
the wait in BPMP firmware during SC7 exit.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch fixes the delay loop used to wake up the BPMP during SC7 exit.
The earlier loop would fail just when the timer was about to wrap-around
(e.g. when TEGRA_TMRUS_BASE is 0xfffffffe, the target value becomes 0,
which would cause the loop to exit before it's expiry).
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch introduces the backend required for implementing the delay
timer API. Tegra has an on-chip free flowing us timer which can be
used as the delay timer.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Update user guide to use Linaro releases

Fix bug in semihosting write function

Use uintptr_t as base address type in ARM driver APIs

This patch sets the 'USE_COHERENT_MEM' flag to '0', so that the
coherent memory region will not be included in the memory map.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The return value from the SYS_WRITE semihosting operation is 0 if
the call is successful or the number of bytes not written, if there
is an error. The implementation of the write function in the
semihosting driver treats the return value as the number of bytes
written, which is wrong. This patch fixes it.

Change-Id: Id39dac3d17b5eac557408b8995abe90924c85b85

This patch reworks the certificate generation tool to follow a data
driven approach. The user may specify at build time the certificates,
keys and extensions defined in the CoT, register them using the
appropiate macros and the tool will take care of creating the
certificates corresponding to the CoT specified.

Change-Id: I29950b39343c3e1b71718fce0e77dcf2a9a0be2f

Linaro produce monthly software releases for the Juno and AEMv8-FVP
platforms. These provide an integrated set of software components
that have been tested together on these platforms.

From now on, it is recommend that Trusted Firmware developers use the
Linaro releases (currently 15.06) as a baseline for the dependent
software components: normal world firmware, Linux kernel and device
tree, file system as well as any additional micro-controller firmware
required by the platform.

This patch updates the user guide to document this new process. It
changes the instructions to get the source code of the full software
stack (including Trusted Firmware) and updates the dependency build
instructions to make use of the build scripts that the Linaro releases
provide.

Change-Id: Ia8bd043f4b74f1e1b10ef0d12cc8a56ed3c92b6e

This patch changes the type of the base address parameter in the
ARM device driver APIs to uintptr_t (GIC, CCI, TZC400, PL011). The
uintptr_t type allows coverage of the whole memory space and to
perform arithmetic operations on the addresses. ARM platform code
has also been updated to use uintptr_t as GIC base address in the
configuration.

Fixes ARM-software/tf-issues#214

Change-Id: I1b87daedadcc8b63e8f113477979675e07d788f1

Implement get_sys_suspend_power_state() handler for Tegra

This patch implements the get_sys_suspend_power_state() handler required by
the PSCI SYSTEM_SUSPEND API. The intent of this handler is to return the
appropriate State-ID field which can be utilized in `affinst_suspend()` to
suspend to system affinity level.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

PSCI: Add SYSTEM_SUSPEND API support

TBB: build 'cert_create' with ECDSA only if OpenSSL supports it

Some Linux distributions include an OpenSSL library which has been
built without ECDSA support. Trying to build the certificate
generation tool on those distributions will result in a build error.

This patch fixes that issue by including ECDSA support only if
OpenSSL has been built with ECDSA. In that case, the OpenSSL
configuration file does not define the OPENSSL_NO_EC macro. The tool
will build successfully, although the resulting binary will not
support ECDSA keys.

Change-Id: I4627d1abd19eef7ad3251997d8218599187eb902

Authentication Framework

This patch updates the user guide, adding instructions to build the
Trusted Firmware with Trusted Board Support using the new framework.

It also provides documentation about the framework itself, including
a detailed section about the TBBR implementation using the framework.

Change-Id: I0849fce9c5294cd4f52981e7a8423007ac348ec6