GitLab

There are couple of issues with how the interrupt routing framework in BL3_1
handles spurious interrupts.

1. In the macro 'handle_interrupt_exception', if a spurious interrupt is
   detected by plat_ic_get_pending_interrupt_type(), then execution jumps to
   'interrupt_exit_\label'. This macro uses the el3_exit() function to return to
   the original exception level. el3_exit() attempts to restore the SPSR_EL3 and
   ELR_EL3 registers with values from the current CPU context. Since these
   registers were not saved in this code path, it programs stale values into
   these registers. This leads to unpredictable behaviour after the execution of
   the ERET instruction.

2. When an interrupt is routed to EL3, it could be de-asserted before the
   GICC_HPPIR is read in plat_ic_get_pending_interrupt_type(). There could be
   another interrupt pending at the same time e.g. a non-secure interrupt. Its
   type will be returned instead of the original interrupt. This would result in
   a call to get_interrupt_type_handler(). The firmware will panic if the
   handler for this type of interrupt has not been registered.

This patch fixes the first problem by saving SPSR_EL3 and ELR_EL3 early in the
'handle_interrupt_exception' macro, instead of only doing so once the validity
of the interrupt has been determined.

The second problem is fixed by returning execution back to the lower exception
level through the 'interrupt_exit_\label' label instead of treating it as an
error condition. The 'interrupt_error_\label' label has been removed since it is
no longer used.

Fixes ARM-software/tf-issues#305

Change-Id: I81c729a206d461084db501bb81b44dff435021e8

In order for the symbol table in the ELF file to contain the size of
functions written in assembly, it is necessary to report it to the
assembler using the .size directive.

To fulfil the above requirements, this patch introduces an 'endfunc'
macro which contains the .endfunc and .size directives. It also adds
a .func directive to the 'func' assembler macro.

The .func/.endfunc have been used so the assembler can fail if
endfunc is omitted.

Fixes ARM-Software/tf-issues#295

Change-Id: If8cb331b03d7f38fe7e3694d4de26f1075b278fc
Signed-off-by: Kévin Petit <kevin.petit@arm.com>

The cpu-ops pointer was initialized before enabling the data cache in the cold
and warm boot paths. This required a DCIVAC cache maintenance operation to
invalidate any stale cache lines resident in other cpus.

This patch moves this initialization to the bl31_arch_setup() function
which is always called after the data cache and MMU has been enabled.

This change removes the need:
 1. for the DCIVAC cache maintenance operation.
 2. to initialise the CPU ops upon resumption from a PSCI CPU_SUSPEND
    call since memory contents are always preserved in this case.

Change-Id: Ibb2fa2f7460d1a1f1e721242025e382734c204c6

This patch modifies the declarations of the functions printf() et al.
and adds the right GCC attribute to request the compiler to check
the type of the arguments passed to these functions against the given
format string. This will ensure that the compiler outputs warning
messages like the following whenever it detects an inconsistency:

 file.c:42: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘long int’

It also fixes the type mismatch inconsistencies that it revealed
across the code base.

NOTE: THIS PATCH MAY FORCE PLATFORM PORTS OR SP/SPDS THAT USE THE
PRINTF FAMILY OF FUNCTIONS TO FIX ANY TYPE MISMATCH INCONSISTENCIES.

Change-Id: If36bb54ec7d6dd2cb4791d89b02a24ac13fd2df6

This patch adds support to call the reset_handler() function in BL3-1 in the
cold and warm boot paths when another Boot ROM reset_handler() has already run.

This means the BL1 and BL3-1 versions of the CPU and platform specific reset
handlers may execute different code to each other. This enables a developer to
perform additional actions or undo actions already performed during the first
call of the reset handlers e.g. apply additional errata workarounds.

Typically, the reset handler will be first called from the BL1 Boot ROM. Any
additional functionality can be added to the reset handler when it is called
from BL3-1 resident in RW memory. The constant FIRST_RESET_HANDLER_CALL is used
to identify whether this is the first version of the reset handler code to be
executed or an overridden version of the code.

The Cortex-A57 errata workarounds are applied only if they have not already been
applied.

Fixes ARM-software/tf-issue#275

Change-Id: Id295f106e4fda23d6736debdade2ac7f2a9a9053

This patch provides an option to specify a interrupt routing model
where non-secure interrupts (IRQs) are routed to EL3 instead of S-EL1.
When such an interrupt occurs, the TSPD arranges a return to
the normal world after saving any necessary context. The interrupt
routing model to route IRQs to EL3 is enabled only during STD SMC
processing. Thus the pre-emption of S-EL1 is disabled during Fast SMC
and Secure Interrupt processing.

A new build option TSPD_ROUTE_NS_INT_EL3 is introduced to change
the non secure interrupt target execution level to EL3.

Fixes ARM-software/tf-issues#225

Change-Id: Ia1e779fbbb6d627091e665c73fa6315637cfdd32

This patch extends the build option `USE_COHERENT_MEMORY` to
conditionally remove coherent memory from the memory maps of
all boot loader stages. The patch also adds necessary
documentation for coherent memory removal in firmware-design,
porting and user guides.

Fixes ARM-Software/tf-issues#106

Change-Id: I260e8768c6a5c2efc402f5804a80657d8ce38773

This patch moves the bakery locks out of coherent memory to normal memory.
This implies that the lock information needs to be placed on a separate cache
line for each cpu. Hence the bakery_lock_info_t structure is allocated in the
per-cpu data so as to minimize memory wastage. A similar platform per-cpu
data is introduced for the platform locks.

As a result of the above changes, the bakery lock api is completely changed.
Earlier, a reference to the lock structure was passed to the lock implementation.
Now a unique-id (essentially an index into the per-cpu data array) and an offset
into the per-cpu data for bakery_info_t needs to be passed to the lock
implementation.

Change-Id: I1e76216277448713c6c98b4c2de4fb54198b39e0

This patch fixes the incorrect value of the LENGTH attribute in
the linker scripts. This attribute must define the memory size, not
the limit address.

Fixes ARM-software/tf-issues#252

Change-Id: I328c38b9ec502debe12046a8912d7dfc54610c46

Initializes SCTLR_EL1 based on MODE_RW bit in SPSR for the entry
point. The RES1 bits for SCTLR_EL1 differs for Aarch64 and Aarch32
mode.

This patch resets the value of CNTVOFF_EL2 before exit to EL1 on
warm boot. This needs to be done if only the Trusted Firmware exits
to EL1 instead of EL2, otherwise the hypervisor would be responsible
for this.

Fixes ARM-software/tf-issues#240

Change-Id: I79d54831356cf3215bcf1f251c373bd8f89db0e0

This patch gathers miscellaneous minor fixes to the documentation, and comments
in the source code.

Change-Id: I631e3dda5abafa2d90f464edaee069a1e58b751b
Co-Authored-By: Soby Mathew <soby.mathew@arm.com>
Co-Authored-By: Dan Handley <dan.handley@arm.com>

This patch adds handlers for dumping Cortex-A57 and Cortex-A53 specific register
state to the CPU specific operations framework. The contents of CPUECTLR_EL1 are
dumped currently.

Change-Id: I63d3dbfc4ac52fef5e25a8cf6b937c6f0975c8ab

This patch adds CPU core and cluster power down sequences to the CPU specific
operations framework introduced in a earlier patch. Cortex-A53, Cortex-A57 and
generic AEM sequences have been added. The latter is suitable for the
Foundation and Base AEM FVPs. A pointer to each CPU's operations structure is
saved in the per-cpu data so that it can be easily accessed during power down
seqeunces.

An optional platform API has been introduced to allow a platform to disable the
Accelerator Coherency Port (ACP) during a cluster power down sequence. The weak
definition of this function (plat_disable_acp()) does not take any action. It
should be overriden with a strong definition if the ACP is present on a
platform.

Change-Id: I8d09bd40d2f528a28d2d3f19b77101178778685d

This patch introduces a framework which will allow CPUs to perform
implementation defined actions after a CPU reset, during a CPU or cluster power
down, and when a crash occurs. CPU specific reset handlers have been implemented
in this patch. Other handlers will be implemented in subsequent patches.

Also moved cpu_helpers.S to the new directory lib/cpus/aarch64/.

Change-Id: I1ca1bade4d101d11a898fb30fea2669f9b37b956

This patch adds support for SYSTEM_OFF and SYSTEM_RESET PSCI
operations. A platform should export handlers to complete the
requested operation. The FVP port exports fvp_system_off() and
fvp_system_reset() as an example.

If the SPD provides a power management hook for system off and
system reset, then the SPD is notified about the corresponding
operation so it can do some bookkeeping. The TSPD exports
tspd_system_off() and tspd_system_reset() for that purpose.

Versatile Express shutdown and reset methods have been removed
from the FDT as new PSCI sys_poweroff and sys_reset services
have been added. For those kernels that do not support yet these
PSCI services (i.e. GICv3 kernel), the original dtsi files have
been renamed to *-no_psci.dtsi.

Fixes ARM-software/tf-issues#218

Change-Id: Ic8a3bf801db979099ab7029162af041c4e8330c8

This patch disables routing of external aborts from lower exception levels to
EL3 and ensures that a SError interrupt generated as a result of execution in
EL3 is taken locally instead of a lower exception level.

The SError interrupt is enabled in the TSP code only when the operation has not
been directly initiated by the normal world. This is to prevent the possibility
of an asynchronous external abort which originated in normal world from being
taken when execution is in S-EL1.

Fixes ARM-software/tf-issues#153

Change-Id: I157b996c75996d12fd86d27e98bc73dd8bce6cd5

Fix the following issues with the console log output:

* Make sure the welcome string is the first thing in the log output
(during normal boot).
* Prefix each message with the BL image name so it's clear which
BL the output is coming from.
* Ensure all output is wrapped in one of the log output macros so it can
be easily compiled out if necessary. Change some of the INFO() messages
to VERBOSE(), especially in the TSP.
* Create some extra NOTICE() and INFO() messages during cold boot.
* Remove all usage of \r in log output.

Fixes ARM-software/tf-issues#231

Change-Id: Ib24f7acb36ce64bbba549f204b9cde2dbb46c8a3

Secure ROM at address 0x0000_0000 is defined as FVP_TRUSTED_ROM
Secure RAM at address 0x0400_0000 is defined as FVP_TRUSTED_SRAM
Secure RAM at address 0x0600_0000 is defined as FVP_TRUSTED_DRAM

BLn_BASE and BLn_LIMIT definitions have been updated and are based on
these new memory regions.

The available memory for each bootloader in the linker script is
defined by BLn_BASE and BLn_LIMIT, instead of the complete memory
region.

TZROM_BASE/SIZE and TZRAM_BASE/SIZE are no longer required as part of
the platform porting.

FVP common definitions are defined in fvp_def.h while platform_def.h
contains exclusively (with a few exceptions) the definitions that are
mandatory in the porting guide. Therefore, platform_def.h now includes
fvp_def.h instead of the other way around.

Porting guide has been updated to reflect these changes.

Change-Id: I39a6088eb611fc4a347db0db4b8f1f0417dbab05

This patch adds support for BL3-2 initialization by asynchronous
method where BL3-1 transfers control to BL3-2 using world switch.
After BL3-2 initialization, it transfers control to BL3-3 via SPD
service handler. The SPD service handler initializes the CPU context
to BL3-3 entrypoint depending on the return function indentifier from
TSP initialization.

Fixes ARM-software/TF-issues#184

Change-Id: I7b135c2ceeb356d3bb5b6a287932e96ac67c7a34

The purpose of platform_is_primary_cpu() is to determine after reset
(BL1 or BL3-1 with reset handler) if the current CPU must follow the
cold boot path (primary CPU), or wait in a safe state (secondary CPU)
until the primary CPU has finished the system initialization.

This patch removes redundant calls to platform_is_primary_cpu() in
subsequent bootloader entrypoints since the reset handler already
guarantees that code is executed exclusively on the primary CPU.

Additionally, this patch removes the weak definition of
platform_is_primary_cpu(), so the implementation of this function
becomes mandatory. Removing the weak symbol avoids other
bootloaders accidentally picking up an invalid definition in case the
porting layer makes the real function available only to BL1.

The define PRIMARY_CPU is no longer mandatory in the platform porting
because platform_is_primary_cpu() hides the implementation details
(for instance, there may be platforms that report the primary CPU in
a system register). The primary CPU definition in FVP has been moved
to fvp_def.h.

The porting guide has been updated accordingly.

Fixes ARM-software/tf-issues#219

Change-Id: If675a1de8e8d25122b7fef147cb238d939f90b5e

This patch further optimizes the EL3 register state stored in
cpu_context. The 2 registers which are removed from cpu_context are:

  * cntfrq_el0 is the system timer register which is writable
    only in EL3 and it can be programmed during cold/warm boot. Hence
    it need not be saved to cpu_context.

  * cptr_el3 controls access to Trace, Floating-point, and Advanced
    SIMD functionality and it is programmed every time during cold
    and warm boot. The current BL3-1 implementation does not need to
    modify the access controls during normal execution and hence
    they are expected to remain static.

Fixes ARM-software/tf-issues#197

Change-Id: I599ceee3b73a7dcfd37069fd41b60e3d397a7b18

Assert a valid security state using the macro sec_state_is_valid().
Replace assert() with panic() in those cases that might arise
because of runtime errors and not programming errors.
Replace panic() with assert() in those cases that might arise
because of programming errors.

Fixes ARM-software/tf-issues#96

Change-Id: I51e9ef0439fd5ff5e0edfef49050b69804bf14d5

This patch adds the CPUECTLR_EL1 register and the CCI Snoop Control
register to the list of registers being reported when an unhandled
exception occurs.

Change-Id: I2d997f2d6ef3d7fa1fad5efe3364dc9058f9f22c

This patch reworks the crash reporting mechanism to further
optimise the stack and code size. The reporting makes use
of assembly console functions to avoid calling C Runtime
to report the CPU state. The crash buffer requirement is
reduced to 64 bytes with this implementation. The crash
buffer is now part of per-cpu data which makes retrieving
the crash buffer trivial.

Also now panic() will use crash reporting if
invoked from BL3-1.

Fixes ARM-software/tf-issues#199

Change-Id: I79d27a4524583d723483165dc40801f45e627da5

This patch reworks the manner in which the M,A, C, SA, I, WXN & EE bits of
SCTLR_EL3 & SCTLR_EL1 are managed. The EE bit is cleared immediately after reset
in EL3. The I, A and SA bits are set next in EL3 and immediately upon entry in
S-EL1. These bits are no longer managed in the blX_arch_setup() functions. They
do not have to be saved and restored either. The M, WXN and optionally the C
bit are set in the enable_mmu_elX() function. This is done during both the warm
and cold boot paths.

Fixes ARM-software/tf-issues#226

Change-Id: Ie894d1a07b8697c116960d858cd138c50bc7a069

Print out Trusted Firmware version at runtime at each BL stage.
Message consists of TF version as defined statically in the Makefile
(e.g. v0.4), build mode (debug|release) and a customizable build
string:

  1. By defining BUILD_STRING in command line when building TF
  2. Default string is git commit ID
  3. Empty if git meta-data is not available

Fixes ARM-software/tf-issues#203

Change-Id: I5c5ba438f66ab68810427d76b49c5b9177a957d6

This patch implements a "tf_printf" which supports only the commonly
used format specifiers in Trusted Firmware, which uses a lot less
stack space than the stdlib printf function.

Fixes ARM-software/tf-issues#116

Change-Id: I7dfa1944f4c1e634b3e2d571f49afe02d109a351

This patch uses stacks allocated in normal memory to enable the MMU early in the
warm boot path thus removing the dependency on stacks allocated in coherent
memory. Necessary cache and stack maintenance is performed when a cpu is being
powered down and up. This avoids any coherency issues that can arise from
reading speculatively fetched stale stack memory from another CPUs cache. These
changes affect the warm boot path in both BL3-1 and BL3-2.

The EL3 system registers responsible for preserving the MMU state are not saved
and restored any longer. Static values are used to program these system
registers when a cpu is powered on or resumed from suspend.

Change-Id: I8357e2eb5eb6c5f448492c5094b82b8927603784

This patch reworks the cold boot path across the BL1, BL2, BL3-1 and BL3-2 boot
loader stages to not use stacks allocated in coherent memory for early platform
setup and enabling the MMU. Stacks allocated in normal memory are used instead.

Attributes for stack memory change from nGnRnE when the MMU is disabled to
Normal WBWA Inner-shareable when the MMU and data cache are enabled. It is
possible for the CPU to read stale stack memory after the MMU is enabled from
another CPUs cache. Hence, it is unsafe to turn on the MMU and data cache while
using normal stacks when multiple CPUs are a part of the same coherency
domain. It is safe to do so in the cold boot path as only the primary cpu
executes it. The secondary cpus are in a quiescent state.

This patch does not remove the allocation of coherent stack memory. That is done
in a subsequent patch.

Change-Id: I12c80b7c7ab23506d425c5b3a8a7de693498f830

This patch re-organizes the memory layout on FVP as to give the
BL3-2 image as much memory as possible.

Considering these two facts:
 - not all images need to live in memory at the same time. Once
   in BL3-1, the memory used by BL1 and BL2 can be reclaimed.
 - when BL2 loads the BL3-1 and BL3-2 images, it only considers the
   PROGBITS sections of those 2 images. The memory occupied by the
   NOBITS sections will be touched only at execution of the BL3-x
   images;
Then it is possible to choose the different base addresses such that
the NOBITS sections of BL3-1 and BL3-2 overlay BL1 and BL2.

On FVP we choose to put:
 - BL1 and BL3-1 at the top of the Trusted RAM, with BL3-1 NOBITS
   sections overlaying BL1;
 - BL3-2 at the bottom of the Trusted RAM, with its NOBITS sections
   overlaying BL2;

This is illustrated by the following diagram:

0x0404_0000 ------------    ------------------
            |   BL1    | <= |  BL3-1 NOBITS  |
            ------------ <= ------------------
            |          | <= | BL3-1 PROGBITS |
            ------------    ------------------
            |   BL2    | <= |  BL3-2 NOBITS  |
            ------------ <= ------------------
            |          | <= | BL3-2 PROGBITS |
0x0400_0000 ------------    ------------------

New platform-specific constants have been introduced to easily check
at link time that BL3-1 and BL3-2 PROGBITS sections don't overwrite
BL1 and BL2. These are optional and the platform code is free to define
them or not. If not defined, the linker won't attempt to check
image overlaying.

Fixes ARM-software/tf-issues#117

Change-Id: I5981d1c3d66ee70eaac8bd052630c9ac6dd8b042

CTX_INCLUDE_FPREGS make variable allows us to include or exclude FP
registers from context structure, in case FP is not used by TSPD.

Fixes ARM-software/tf-issues#194

Change-Id: Iee41af382d691340c7ae21830ad1bbf95dad1f4b

Exclude stdlib files because they do not follow kernel code style.

Fixes ARM-software/tf-issues#73

Change-Id: I4cfafa38ab436f5ab22c277cb38f884346a267ab

This patch reworks FVP specific code responsible for determining
the entry point information for BL3-2 and BL3-3 stages when BL3-1
is configured as the reset handler.

Change-Id: Ia661ff0a6a44c7aabb0b6c1684b2e8d3642d11ec

Consolidate all BL3-1 CPU context initialization for cold boot, PSCI
and SPDs into two functions:
*  The first uses entry_point_info to initialize the relevant
   cpu_context for first entry into a lower exception level on a CPU
*  The second populates the EL1 and EL2 system registers as needed
   from the cpu_context to ensure correct entry into the lower EL

This patch alters the way that BL3-1 determines which exception level
is used when first entering EL1 or EL2 during cold boot - this is now
fully determined by the SPSR value in the entry_point_info for BL3-3,
as set up by the platform code in BL2 (or otherwise provided to BL3-1).

In the situation that EL1 (or svc mode) is selected for a processor
that supports EL2, the context management code will now configure all
essential EL2 register state to ensure correct execution of EL1. This
allows the platform code to run non-secure EL1 payloads directly
without requiring a small EL2 stub or OS loader.

Change-Id: If9fbb2417e82d2226e47568203d5a369f39d3b0f

The crash reporting support and early initialisation of the
cpu_data allow the runtime_exception vectors to be used from
the start in BL3-1, removing the need for the additional
early_exception vectors and 2KB of code from BL3-1.

Change-Id: I5f8997dabbaafd8935a7455910b7db174a25d871

Moving the context pointers for each CPU into the per-cpu data
allows for much more efficient access to the contexts for the
current CPU.

Change-Id: Id784e210d63cbdcddb44ac1591617ce668dbc29f

This patch prepares the per-cpu pointer cache for wider use by:
* renaming the structure to cpu_data and placing in new header
* providing accessors for this CPU, or other CPUs
* splitting the initialization of the TPIDR pointer from the
  initialization of the cpu_data content
* moving the crash stack initialization to a crash stack function
* setting the TPIDR pointer very early during boot

Change-Id: Icef9004ff88f8eb241d48c14be3158087d7e49a3

This patch makes the console crash dump of processor register
state optional based on the CRASH_REPORTING make variable.

This defaults to only being enabled for DEBUG builds. This can
be overridden by setting a different value in the platform
makefile or on the make command line.

Change-Id: Icfa1b2d7ff0145cf0a85e8ad732f9cee7e7e993f

All callers of cm_get_context() pass the calling CPU MPIDR to the
function. Providing a specialised version for the current
CPU results in a reduction in code size and better readability.

The current function has been renamed to cm_get_context_by_mpidr()
and the existing name is now used for the current-CPU version.

The same treatment has been done to cm_set_context(), although
only both forms are used at present in the PSCI and TSPD code.

Change-Id: I91cb0c2f7bfcb950a045dbd9ff7595751c0c0ffb