GitLab

This patch updates the state machine to "not present" if the bpmp
firmware is not found in the system during boot. The suspend
handler also checks now if the interface exists, before updating
the internal state machine.

Reported by: Kalyani Chidambaram Vaidyanathan <kalyanic@nvidia.com>

Change-Id: If8fd7f8e412bb603944555c24826855226e7f48c
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch toggles the ring oscillator state across cluster idle
as DFLL loses its state. We dont want garbage values being written
to the pmic when we enter cluster idle state, so enable "open loop"
when we enter CC6 and restore the state to "closed loop" on exit.

Change-Id: I56f4649f57bcc651d6c415a6dcdc978e9444c97b
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch clears the PMC's DPD registers on resuming from System
Suspend, for all Tegra210 platforms that support the sc7entry-fw.

Change-Id: I7881ef0a5f609ed28b158bc2f4016abea3c7f305
Signed-off-by: kalyani chidambaram <kalyanic@nvidia.com>

The BPMP firmware takes some time to initialise its state on exiting
System Suspend state. The CPU needs to synchronize with the BPMP during
this process to avoid any race conditions. This patch suspends and resumes
the BPMP interface across a System Suspend cycle, to fix this race.

Change-Id: I82a61d12ef3eee267bdd8d4386bed23397fbfd2d
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds suspend and resume handlers for the BPMP
interface. Mark the interface as "suspended" before entering
System Suspend and verify that BPMP is alive on exit.

Change-Id: I74ccbc86125079b46d06360fc4c7e8a5acfbdfb2
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch skips past the signature header added to the sc7entry-fw
binary by the previous level bootloader. Currently, the size of
the header is 1KB, so adjust the start address and the binary size
at the time of copy.

Change-Id: Id0494548009749035846d54df417a960c640c8f9
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch uses the sc7entry-fw base/size values to calculate the
TZDRAM fence, so as to move sc7entry-fw inside the TZDRAM fence.

Change-Id: I91aeeeece857076c478cdc4c18a6ad70dc265031
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds SiP handler for Tegra210 platforms to service
read/write requests for PMC block. None of the secure registers
are accessible to the NS world though.

Change-Id: I7dc1f10c6a6ee6efc642ddcfb1170fb36d3accff
Signed-off-by: kalyani chidambaram <kalyanic@nvidia.com>

This patch puts all the DMA masters in reset before starting the System
Suspend sequence. This helps us make sure that there are no rogue agents
in the system trying to over-write the SC7 Entry Firmware with their own.

Change-Id: I7eb39999d229951e612fbfeb9f86c4efb8f98b5a
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support to enter System Suspend on Tegra210 platforms
without the traditional BPMP firmware. The BPMP firmware will no longer
be supported on Tegra210 platforms and its functionality will be
divided across the CPU and sc7entry-fw.

The sc7entry-fw takes care of performing the hardware sequence required
to enter System Suspend (SC7 power state) from the COP. The CPU is required
to load this firmware to the internal RAM of the COP and start the sequence.
The CPU also make sure that the COP is off after cold boot and is only
powered on when we want to start the actual System Suspend sequence.

The previous bootloader loads the firmware to TZDRAM and passes its base and
size as part of the boot parameters. The EL3 layer is supposed to sanitize
the parameters before touching the firmware blob.

To assist the warmboot code with the PMIC discovery, EL3 is also supposed to
program PMC's scratch register #210, with appropriate values. Without these
settings the warmboot code wont be able to get the device out of System
Suspend.

Change-Id: I5a7b868512dbfd6cfefd55acf3978a1fd7ebf1e2
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes support for powering down a CPU cluster on
Tegra210 platforms as none of them actually use it.

Change-Id: I9665634cf2b5b7b8a1b5a2700cae152dc9165fe3
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support to enter/exit to/from cluster idle power
state on Tegra210 platforms that do not load BPMP firmware.

The CPU initates the cluster idle sequence on the last standing
CPU, by following these steps:

Entry
-----
* stop other CPUs from waking up
* program the PWM pinmux to tristate for OVR PMIC
* program the flow controller to enter CC6 state
* skip L1 $ flush during cluster power down, as L2 $ is inclusive
  of L1 $ on Cortex-A57 CPUs

Exit
----
* program the PWM pinmux to un-tristate for OVR PMIC
* allow other CPUs to wake up

This patch also makes sure that cluster idle state entry is not
enabled until CL-DVFS is ready.

Change-Id: I54cf31bf72b4a09d9bf9d2baaed6ee5a963c7808
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a helper function to find the last standing CPU
in a cluster.

Change-Id: Id018f1958f458c772c7b0c52af8ddf7532b1cec5
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch moves the PLAT_PHY_ADDR_SPACE_SIZE & PLAT_VIRT_ADDR_SPACE
macros to tegra_def.h, to define the virtual/physical address space
size on the platform.

Change-Id: I1c5d264c7ffc1af0e7b14cc16ae2c0416efc76f6
Signed-off-by: Steven Kao <skao@nvidia.com>

This patch organizes the memory and mmio maps linearly, to make the
mmap_add_region process faster. The microsecond timer has been moved
to individual platforms instead of making it a common step, as it
further speeds up the memory map creation process.

Change-Id: I6fdaee392f7ac5d99daa182380ca9116a001f5d6
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch enables the watchdog timer's interrupt as an FIQ
interrupt to the CPU. The interrupt generated by the watchdog
is connected to the flow controller for power management reasons,
and needs to be routed to the GICD for it to reach the CPU.

Change-Id: I9437b516da2c5d763eca72694ed7f3c7389b3d9e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds helper functions to help platforms with cluster state entry
and exit decisions.

* tegra_fc_ccplex_pgexit_lock(): lock CPU power ungate
* tegra_fc_ccplex_pgexit_unlock(): unlock CPU power ungate
* tegra_fc_is_ccx_allowed(): CCx state entry allowed on this CPU?

Change-Id: I6490d34bf380dc03ae203eb3028f61984f06931c
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes the error print displayed when bpmp init
fails. On platforms that do not load the bpmp firmware, this
print is seen on every cluster idle and powerdown request,
cluttering the logs.

Change-Id: I9e30007a913080406052fc32d5360ff70a019d75
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support to handle secure PPIs for Tegra watchdog timers. This
functionality is currently protected by the ENABLE_WDT_LEGACY_FIQ_HANDLING
configuration variable and is only enabled for Tegra210 platforms, for now.

Change-Id: I0752ef54a986c58305e1bc8ad9be71d4a8bbd394
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

On earlier Tegra platforms, e.g. Tegra210, the watchdog timer's FIQ interrupt
is not direclty wired to the GICD. It goes to the flow controller instead, for
power state management. But the flow controller can route the FIQ to the GICD,
as a PPI, which can then get routed to the target CPU.

This patch adds routines to enable/disable routing the legacy FIQ used by
the watchdog timers, to the GICD.

Change-Id: Idd07c88c8d730b5f0e93e3a6e4fdc59bdcb2161b
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Whenever the VPR memory is resized, the GPU is put into reset first
and then the new VPR parameters are programmed to the memory controller
block. There exists a scenario, where the GPU might be out before we
program the new VPR parameters. This means, the GPU would still be
using older settings and leak secrets.

This patch puts the GPU back into reset, if it is out of reset after
resizing VPR, to mitigate this hole.

Change-Id: I38a1000e3803f80909efcb02e27da4bd46909931
Signed-off-by: Jeetesh Burman <jburman@nvidia.com>

This patch updates the secure interrupt handler to mark the interrupt
as complete in case the NS world has not registered a handler.

Change-Id: Iebe952305f7db46375303699b6150611439475df
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support to the bpmp_ipc driver to allow clients to
enable/disable clocks to hardware blocks. Currently, the API only
supports SE devices.

Change-Id: I9a361e380c0bcda59f5a92ca51c86a46555b2e90
Signed-off-by: steven kao <skao@nvidia.com>

The GICD registers are 32-bits wide whereas the crash handler was reading
them as 64-bit ones. This patch fixes the code to read the GICD registers,
32-bits at a time, from the paltform's crash handler.

Change-Id: If3d6608529684ecc02be6a1b715012310813b2a4
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a default implementation for the platform specific
CPU standby power handler. Tegra SoCs can override this handler
with their own implementations.

Change-Id: I91e513842f194b1e2b1defa2d833bb4d9df5f06b
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Modifying smmu macros to pass base address of smmu so that it can be
used with multiple smmus.

Added macro for combining smmu backup regs that can be used for multiple
smmus.

Change-Id: I4f3bb83d66d5df14a3b91bc82f7fc26ec8e4592e
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>

This patch removes this unused config option from the Tegra186
platform makefiles.

Change-Id: Idcdf6854332a26599323a247289c2d3ce19f475f
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes the usage of this platform config, as it is always
enabled by all the supported platforms.

Change-Id: Ie7adb641adeb3604b177b6960b797722d60addfa
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a platform setup handler that gets called after
the MMU is enabled. Platforms wanting to make use of this handler
should declare 'plat_late_platform_setup' handler in their platform
files, to override the default weakly defined handler.

Change-Id: Ibc97a2e5a24608ddea856d0bd543a9d5876f604c
Signed-off-by: Dilan Lee <dilee@nvidia.com>

There are Tegra platforms which have limited UART ports and so
all the components have to share the console. The SPE helps out
by collecting all the logs in such cases and prints them on the
shared UART port.

This patch adds a driver to communicate with the SPE driver, which
in turn provides the console.

Change-Id: Ie750520b936b8bed0ab1d876f03fc0a3490a85a3
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch includes the console driver from individual platform
makefiles and removes it from tegra_common.mk. This allows future
platforms to include consoles of their choice.

Change-Id: I7506562bfac78421a80fb6782ac8472fbef6cfb0
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Tegra SoCs currently do not have a SMMU register at address 0xFFFFFFFF.
This patch changes the search criteria, to look for this marker, to
calculate the size of the saved context.

Change-Id: I15d91945ecb78267f91c45f37985dbb2327ca3ae
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The Tegra memctrl driver sets up the TZDRAM fence during boot and
system suspend exit. This patch provides individual platforms with
handlers to perform custom steps during TZDRAM setup.

Change-Id: Iee094d6ca189c6dd24f1147003c33c99ff3a953b
Signed-off-by: Steven Kao <skao@nvidia.com>

This patch adds support to save the system suspend entry and exit
markers to TZDRAM to help the trampoline code decide if the current
warmboot is actually an exit from System Suspend.

The Tegra186 platform handler sets the system suspend entry marker
before entering SC7 state and the trampoline flips the state back to
system resume, on exiting SC7.

Change-Id: I29d73f1693c89ebc8d19d7abb1df1e460eb5558e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a helper function to get the SMMU context's offset
and uses another helper function to get the CPU trampoline offset.
These helper functions are used by the System Suspend entry sequence
to save the SMMU context and CPU reset handler to TZDRAM.

Change-Id: I95e2862fe37ccad00fa48ec165c6e4024df01147
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch returns error if BPMP initialization fails. The platform
code marks the cluster as "runnning" since we wont be able to get
it into the low power state without BPMP.

Change-Id: I86f51d478626240bb7b4ccede8907674290c5dc1
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch renames all the secure scratch registers to reflect their
usage.

This is a list of all the macros being renamed:

- SECURE_SCRATCH_RSV1_* -> SCRATCH_RESET_VECTOR_*
- SECURE_SCRATCH_RSV6 -> SCRATCH_SECURE_BOOTP_FCFG
- SECURE_SCRATCH_RSV11_* -> SCRATCH_SMMU_TABLE_ADDR_*
- SECURE_SCRATCH_RSV53_* -> SCRATCH_BOOT_PARAMS_ADDR_*
- SECURE_SCRATCH_RSV55_* -> SCRATCH_TZDRAM_ADDR_*

NOTE: Future SoCs will have to define these macros to
      keep the drivers functioning.

Change-Id: Ib3ba40dd32e77b92b47825f19c420e6fdfa8b987
Signed-off-by: Steven Kao <skao@nvidia.com>

The Tegra memctrl driver sets up the TZDRAM fence during boot and
system suspend exit. This patch provides individual platforms with
handlers to perform platform specific steps, e.g. enable encryption,
save base/size to secure scratch registers.

Change-Id: Ifaa2e0eac20b50f77ec734256544c36dd511bd63
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch fixes the following MISRA violations:

Rule 8.6: Externally-linked object or function has "no" definition(s).
Rule 11.1: A cast shall not convert a pointer to a function to
any other type.

Change-Id: Ic1f6fc14c744e54ff782c6987dab9c9430410f5e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch sanity checks the target cluster value, during core power on,
by comparing it against the maximum number of clusters supported by the
platform.

Reported by: Rohit Khanna <rokhanna@nvidia.com>

Change-Id: Ia73ccf04bd246403de4ffff6e5c99e3b00fb98ca
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>