GitLab

This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.

The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.

Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.

The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.

Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This reverts commit 2f18aa1f

.

It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.

Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Normally, BL33 needs to contain a boot loader like U-Boot or UEFI that
eventually gives control to the OS. However, in some cases, this boot
sequence may be too slow. For example, when doing tests in a
cycle-accurate emulator, the user may only be interested in the
interaction between the Trusted Firmware and the OS, not in the boot
process itself.

The new option ARM_LINUX_KERNEL_AS_BL33 allows BL33 to contain the Linux
kernel image by changing the value of registers x0-x3 to the values
expected by the kernel. This option requires the device tree blob (DTB)
to be present in memory. Its address must be specified in the newly
introduced ARM_PRELOADED_DTB_BASE build option. For now, it only supports
AArch64 kernels.

This option is only available when RESET_TO_BL31=1. For this reason
the BL33 binary must be preloaded in memory and PRELOADED_BL33_BASE must
be used.

For example, if the kernel is loaded at 0x80080000 and the DTB is loaded
at address 0x82000000, the firmware could be built like this:

    CROSS_COMPILE=aarch64-linux-gnu-  \
    make PLAT=fvp DEBUG=1             \
    RESET_TO_BL31=1                   \
    ARM_LINUX_KERNEL_AS_BL33=1        \
    PRELOADED_BL33_BASE=0x80080000    \
    ARM_PRELOADED_DTB_BASE=0x82000000 \
    all fip

Change-Id: If9dc847c65ae2d0c27b51f0fd44fc06b28497db9
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size of BL31 has been increased in builds with SPM.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

  - Assign 0x10 for RAS exceptions on ARM platforms, and install
    EHF priority descriptor.

  - Call the common RAS initialisation from ARM BL31 setup.

  - Add empty definitions for platform error records and RAS interrupts.

Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.

The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.

Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp SPD=tspd TRUSTED_BOARD_BOOT=1 \
	     GENERATE_COT=1 ARM_ROTPK_LOCATION=devel_rsa \
	     ROT_KEY=arm_rotprivk_rsa.pem MBEDTLS_DIR=mbedtls all

Change-Id: Ie4cd6011b3e4fdcdd94ccb97a7e941f3b5b7aeb8
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I32b223251b8bf5924149d89431a65d3405a73d3e
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.

This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>

Ensure (where possible) that switch statements in plat comply with MISRA
rules 16.1 - 16.7.

Change-Id: Ie4a7d2fd10f6141c0cfb89317ea28a755391622f
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>

When the source code says 'SMCC' it is talking about the SMC Calling
Convention. The correct acronym is SMCCC. This affects a few definitions
and file names.

Some files have been renamed (smcc.h, smcc_helpers.h and smcc_macros.S)
but the old files have been kept for compatibility, they include the
new ones with an ERROR_DEPRECATED guard.

Change-Id: I78f94052a502436fdd97ca32c0fe86bd58173f2f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.

In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.

Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.

Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This issue was detected when testing FWU on Juno. The Timer
`timer_ops` was not being initialized before being used by
the SDS driver on Juno. This patch adds the call to
`generic_delay_timer_init()` during bl2u_early_platform_setup().
This is done generically for all ARM platforms because the
cost involved is minimal.

Change-Id: I349cf0bd1db68406eb2298b65f9c729f792cabdc
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.

The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.

Fixes ARM-software/tf-issues#559

Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Change-Id: I1d85b76af002b8b672fcaeca94939b7420bc8243
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.

Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.

Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Change-Id: I93e491fde2a991fc39584c2762f33cbea40541e3
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Change-Id: Iadb21bb56f2e61d7e6aec9b3b3efd30059521def
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The console core flush API expects the base address in the first
register, but ARM helpers currently sets the second register with the
base address. This causes an assert failure.

This patch fixes that.

Change-Id: Ic54c423cd60f2756902ab3cfc77b3de2ac45481e
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

In the next commit, I need the image name in lowercase because
output files are generally named in lowercase.

Unfortunately, TOOL_ADD_IMG takes the first argument in uppercase
since we generally use uppercase Make variables.

make_helpers/build_macros.mk provides 'uppercase' macro to convert
a string into uppercase, but 'lowercase' does not exist.  We can
implement it if we like, but it would be more straightforward to
change the argument of TOOL_ADD_IMG.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Now FIP_ADD_IMG takes care of both fiptool and cert_create
symmetrically.  Rename it so that it matches the behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The build system supports generating two FIP images, fip and fwu_fip.
Accordingly, we have similar build macros.

   FIP_ADD_PAYLOAD   <-->  FWU_FIP_ADD_PAYLOAD
   CERT_ADD_CMD_OPT  <-->  FWU_CERT_ADD_CMD_OPT
   FIP_ADD_IMG       <-->  FWU_FIP_ADD_IMG

The duplicated code increases the maintenance burden.  Also, the build
rule of BL2U looks clumsy - we want to call MAKE_BL to compile it from
source files, but we want to put it in fwu_fip.  We can not do it in a
single macro call since the current MAKE_BL does not support fwu_fip.

To refactor those in a clean way is to support one more argument to
specify the FIP prefix.  If it is empty, the images are targeted to
fip, whereas if the argument is "FWU_", targeted to fwu_fip.

The build macros prefixed with FWU_ go away.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.

The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:

	--data cluster0.cpu0=bl2.bin@0x4001000
	-C cluster0.cpu0.RVBAR=0x4001000

These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.

Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

To allow BL31 to grow in SRAM, move TSP in TZC secured DRAM
by default.

Increase the BL31 max limit by one page.

Change-Id: Idd3479be02f0f9bafac2f275376d7db0c2015431
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.

Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch allows non-secure bus masters to access TZC region0 as well
as the EL3 Payload itself.

Change-Id: I7e44f2673a2992920d41503fb4c57bd7fb30747a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Factor out SPE operations in a separate file.  Use the publish
subscribe framework to drain the SPE buffers before entering secure
world.  Additionally, enable SPE before entering normal world.

A side effect of this change is that the profiling buffers are now
only drained when a transition from normal world to secure world
happens.  Previously they were drained also on return from secure
world, which is unnecessary as SPE is not supported in S-EL1.

Change-Id: I17582c689b4b525770dbb6db098b3a0b5777b70a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Support SDEI on ARM platforms using frameworks implemented in earlier
patches by defining and exporting SDEI events: this patch defines the
standard event 0, and a handful of shared and private dynamic events.

Change-Id: I9d3d92a92cff646b8cc55eabda78e140deaa24e1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Define number of priority bits, and allocate priority levels for SDEI.

Change-Id: Ib6bb6c5c09397f7caef950c4caed5a737b3d4112
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Provide a strong definition for plat_sdei_validate_sdei_entrypoint()
which translates client address to Physical Address, and then validating
the address to be present in DRAM.

Change-Id: Ib93eb66b413d638aa5524d1b3de36aa16d38ea11
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The function arm_validate_ns_entrypoint() validates a given non-secure
physical address. This function however specifically returns PSCI error
codes.

Non-secure physical address validation is potentially useful across ARM
platforms, even for non-PSCI use cases. Therefore make this function
common by returning 0 for success or -1 otherwise.

Having made the function common, make arm_validate_psci_entrypoint() a
wrapper around arm_validate_ns_entrypoint() which only translates return
value into PSCI error codes. This wrapper is now used where
arm_validate_ns_entrypoint() was currently used for PSCI entry point
validation.

Change-Id: Ic781fc3105d6d199fd8f53f01aba5baea0ebc310
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch brings in the following fixes:

  - The per-PE target data initialized during power up needs to be
    flushed so as to be visible to other PEs.

  - Setup per-PE target data for the primary PE as well. At present,
    this was only setup for secondary PEs when they were powered on.

Change-Id: Ibe3a57c14864e37b2326dd7ab321a5c7bf80e8af
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This initial port of the Secure Partitions Manager to FVP supports BL31
in both SRAM and Trusted DRAM.

A document with instructions to build the SPM has been added.

Change-Id: I4ea83ff0a659be77f2cd72eaf2302cdf8ba98b32
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Achin Gupta <achin.gupta@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

ARM_TSP_RAM_LOCATION_ID was defined only in AARCH64, but the macro
was also used in AARCH32, and it meant that it was taking the value 0,
which happened to equal ARM_TRUSTED_SRAM_ID.

Change-Id: If9f4dbee1a2ba15e7806f2a03305b554bd327363
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

On Arm standard platforms, it runs out of SRAM space when TBB is
enabled, so the TSP default location is changed to dram when TBB
is enabled.

Change-Id: I516687013ad436ef454d2055d4e6fce06e467044
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>

An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.

This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms.  The
deprecated interrupt list definitions are however retained to support
legacy builds.

Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.

NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.

Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>