GitLab

Add supprot for Marvell platforms based on Armada-37xx SoC.
This includes support for the official Armada-3720 modular
development board and EspressoBin community board.
The Armada-37xx SoC contains dual Cortex-A53 Application CPU,
single secure CPU (Cortex-M3) and the following interfaces:
- SATA 3.0
- USB 3.0 and USB 2.0
- PCIe
- SDIO (supports boot from eMMC)
- SPI
- UART
- I2c
- Gigabit Ethernet
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Even though at this point plat_crash_console_flush is optional, it will
stop being optional in a following patch.

The console driver of warp7 doesn't support flush, so the implementation
is a placeholder.

TI had ``plat_crash_console_init`` and ``plat_crash_console_putc``, but
they weren't global so they weren't actually used. Also, they were
calling the wrong functions.

imx8_helpers.S only has placeholders for all of the functions.

Change-Id: I8d17bbf37c7dad74e134c61ceb92acb9af497718
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Move doimage utility from toos/doimage to tools/marvell/doimage.
This is done for supporting mode Marvell tools in the future.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Some of COMPHY parameters depends on the hw connection between the SoC
and the PHY, which can vary on different boards e.g. due to different
wires length. Define the "porting layer" with some defaults
parameters. It ease updating static values which needs to be updated due
to board differences, which are now grouped in one place.

Example porting layer for a8k-db is under:
plat/marvell/a8k/a80x0/board/phy-porting-layer.h

If for some boards parameters are not defined (missing
phy-porting-layer.h), the default values are used
(drivers/marvell/comphy/phy-default-porting-layer.h)
and the following compilation warning is show:
"Using default comphy params - you may need to suit them to your board".

The common COMPHY driver code is extracted in order to be shared with
future COMPHY driver for A3700 SoC platforms
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

The "Secure" prefix (S-ELx) is valid only for S-EL0 and S-EL1 but is
meaningless for EL3, since EL3 is always secure. Hence, the "S" prefix
has been removed from wherever it was used as "S-EL3".

Change-Id: Icdeac9506d763f9f83d7297c7113aec7b85e9dbe
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

Before switching to new API the scp_bl2 handler was invoked from
bl2/bl2_image_load.c which was removed. Invoke the platform specific
scp_bl2 handler in analogy to ARM and HiSilicon.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

The BLE is the pre-TF-A boot stage required by Marvell Armada
BootROM for bringing up DRAM and allow the boot image copy to it.
Since this is not a standard boot level and only uses the TF-A
as a build environment, it was introduced out of source tree.
However it turns out that such remote location introduces additional
complexity to the upstream TF-A build process.
In order to simplify the build environment the BLE source folder
is relocated from the external repository to A8K platform directory.
The build documentation is updated accordingly.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

- Fix build issue
- Add initial memory parameters descriptors for BL2
- Migrate to image load V2

Basic build and run test passed on MacchiatoBin board.
Need to fix the service CPU (CM3) image load procesure and test
OPTEE functionality, which probably will require additional work.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

- Migrate to bl2_early_platform_setup2().
- Remove references to removed build options.
- Use private definition of bl31_params_t.

This is an incomplete migration, the platform doesn't currently compile.

Change-Id: I1ae477b1f2489f49b651528050fdf06e4a55e425
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which
is also used by Allwinner.

As Mentor Graphics allows a lot of customization, the MI2CV in the two
SoC families are not compatible, and driver modifications are needed.

Extract the common code to a MI2CV driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

Change-Id: I908844364bf8080612aaa6d750d7d2441ecc2eb8
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

- add svc configuration according to values burnt
  to the chip efuse

Change-Id: Icf5d7cc41bc09ac2244d0a126106e681afebb064
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Some customers are missing host libraries required for doimage
builds.
This patch requests for the library installation check for every
doimage build and suggest the required installation steps in case
of missing headers.

Change-Id: Icde18c3d4d6045f65e50d2dc9e6514971f40033e
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>

This patch enables handling PMU overflow IRQ by GIC SPI's
directly in EL3. Also implement additional SMC routine,
which can disable the solution on demand in runtime.

Since it is possible to configure PMU interrupt trigger type
in the MADT ACPI table, it is enough to set it only once in EL3
during initialization.

Change-Id: Ie76aa62ccc4fd7cabfec9e3d5ed9970ada1c1b2a
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Current default behavior of cpu_standby callback
is problematic during the SBSA test, which is
unable to run due to EL3 panic. Make it dependent on
the PM firmware running.

Change-Id: I7a53de8c880bd23b157dd65ce14bb48b5a5c76c8
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

In order to allow the use of PCIe cards such as graphics cards, whose
demands for BAR space are typically much higher than those of network
or SATA/USB cards, reconfigure the I/O windows so we can declare two
MMIO PCI regions: a 512 MB MMIO32 one at 0xc000_0000 and a 4 GB MMIO64
one at 0x8_0000_0000. In addition, this will leave ample room for an
ECAM config space at 0xe000_0000 (up to the ECAM maximum of 256 MB)

For compatibility with older kernels or firmware, leave the original
16 MB window in place as well.

Change-Id: Ia8177194e542078772f90941eced81b231c16887
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

In order to allow the use of PCIe cards such as graphics cards, whose
demands for BAR space are typically much higher than those of network
or SATA/USB cards, reconfigure the I/O windows so we can declare two
MMIO PCI regions: a 512 MB MMIO32 one at 0xc000_0000 and a 4 GB MMIO64
one at 0x8_0000_0000. In addition, this will leave ample room for an
ECAM config space at 0xe000_0000 (up to the ECAM maximum of 256 MB)

For compatibility with older kernels or firmware, leave the original
16 MB window in place as well.

Change-Id: I80b00691ae8d0a3f3f7285b8e0bfc21c0a095e94
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Define the RT service space as secure with use of memory controller
trustzone feature. Thanks to this protection, any NS-Bootloader nor NS-OS,
won't be able to access RT services (e.g. accidentally overwrite it,
which will at best result in RT services unavailability).

Change-Id: Ie5b6cbe9a1b77879d6d8f8eac5d4e41e468496ce
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Rename a8k_common.h to armada_common.h to keep the same header
name across all other Marvell Armada platforms.
This is especially useful since various Marvell platforms may
use common platform files and share the driver modules.

Change-Id: I7262105201123d54ccddef9aad4097518f1e38ef
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Move from bl31_early_platform_setup to bl31_early_platform_setup2
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Functions provided by stdio.h such as printf and sprintf are available
in the codebase, but they add a lot of code to the final image if they
are used:

- AArch64: ~4KB
- AArch32: ~2KB in T32, ~3KB in A32

tf_printf and tf_snprintf are a lot more simple, but it is preferable
to use them when possible because they are also used in common code.

Change-Id: Id09fd2b486198fe3d79276e2c27931595b7ba60e
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Add support for A8K platform boards

Change-Id: Ife025d930d2ab6cabbc13bbe19b2273cc1c938c8
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Add common Marvell ARMADA platform components.
This patch also includes common components for Marvell
ARMADA 8K platforms.

Change-Id: I42192fdc6525a42e46b3ac2ad63c83db9bcbfeaf
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>