GitLab

Move print_reset_reason function to bl2_plat_setup.c
Put __unused attribute for unused bl2_el3_early_platform_setup args.
Rename dt_dev_info to dt_uart_info.
Put MMU configuration earlier.
Remove unused macros.
Use U() or ULL() macros where needed.
Use device tree to configure GIC.
Use GIC helper function.

Change-Id: I34620c421cc6967a668bca318f7689fd74fa78a6
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

This is the correct name of the IP.
Rename stm32mp1_pmic files to stm32mp_pmic.

Change-Id: I238a7d1f9a1d099daf7788dc9ebbd3146ba2f15f
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Signed-off-by: Yann Gautier <yann.gautier@st.com>

The DDR driver is under dual license, BSD and GPLv2.
The configuration parameters are taken from device tree.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

If a PMIC companion chip is present on board, it has to be configured
for regulators supplies.
This check is done with board DT configuration.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

This will be used by BL33 to get boot device and instance.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

The clock driver is under dual license, BSD and GPLv2.
The clock driver uses device tree, so a minimal support for this is added.
The required files for driver and DTS files are in include/dt-bindings/.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

STM32MP1 is a microprocessor designed by STMicroelectronics,
based on a dual Arm Cortex-A7.
It is an Armv7-A platform, using dedicated code from TF-A.

STM32MP1 uses BL2 compiled with BL2_AT_EL3.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>