GitLab

This patch removes the error print displayed when bpmp init
fails. On platforms that do not load the bpmp firmware, this
print is seen on every cluster idle and powerdown request,
cluttering the logs.

Change-Id: I9e30007a913080406052fc32d5360ff70a019d75
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support to handle secure PPIs for Tegra watchdog timers. This
functionality is currently protected by the ENABLE_WDT_LEGACY_FIQ_HANDLING
configuration variable and is only enabled for Tegra210 platforms, for now.

Change-Id: I0752ef54a986c58305e1bc8ad9be71d4a8bbd394
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

On earlier Tegra platforms, e.g. Tegra210, the watchdog timer's FIQ interrupt
is not direclty wired to the GICD. It goes to the flow controller instead, for
power state management. But the flow controller can route the FIQ to the GICD,
as a PPI, which can then get routed to the target CPU.

This patch adds routines to enable/disable routing the legacy FIQ used by
the watchdog timers, to the GICD.

Change-Id: Idd07c88c8d730b5f0e93e3a6e4fdc59bdcb2161b
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Whenever the VPR memory is resized, the GPU is put into reset first
and then the new VPR parameters are programmed to the memory controller
block. There exists a scenario, where the GPU might be out before we
program the new VPR parameters. This means, the GPU would still be
using older settings and leak secrets.

This patch puts the GPU back into reset, if it is out of reset after
resizing VPR, to mitigate this hole.

Change-Id: I38a1000e3803f80909efcb02e27da4bd46909931
Signed-off-by: Jeetesh Burman <jburman@nvidia.com>

This patch updates the secure interrupt handler to mark the interrupt
as complete in case the NS world has not registered a handler.

Change-Id: Iebe952305f7db46375303699b6150611439475df
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support to the bpmp_ipc driver to allow clients to
enable/disable clocks to hardware blocks. Currently, the API only
supports SE devices.

Change-Id: I9a361e380c0bcda59f5a92ca51c86a46555b2e90
Signed-off-by: steven kao <skao@nvidia.com>

The GICD registers are 32-bits wide whereas the crash handler was reading
them as 64-bit ones. This patch fixes the code to read the GICD registers,
32-bits at a time, from the paltform's crash handler.

Change-Id: If3d6608529684ecc02be6a1b715012310813b2a4
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a default implementation for the platform specific
CPU standby power handler. Tegra SoCs can override this handler
with their own implementations.

Change-Id: I91e513842f194b1e2b1defa2d833bb4d9df5f06b
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Modifying smmu macros to pass base address of smmu so that it can be
used with multiple smmus.

Added macro for combining smmu backup regs that can be used for multiple
smmus.

Change-Id: I4f3bb83d66d5df14a3b91bc82f7fc26ec8e4592e
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>

The ATF code fails to build with PMIC_ROHM_BD9571=0, add the missing
function into the PWRC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Allow auto-detecting E3 when RCAR_LSI is set to RCAR_AUTO.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

The macro is not used, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

This reverts commit d48536e2

,
which misbehaves on R-Car H3 ES2.0. Until the reason for that
misbehavior is understood, revert the commit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Current implementation of i.MX8QX power management related
features does NOT optimize power number, all system resources
like CCI, DDR, and A cluster etc. are kept in STBY mode (powered
ON) when system suspend or CPU hotplug.

To lower the power number, OFF mode should be adopted for those
system resources whenever they can be OFF, A cluster will be OFF
if the CPUs in the cluster are all off line, DDR/MU/DB can be OFF
if system suspend, IRQ steer can be OFF if the wakeup source is
belonged to system controller partition, so wakeup source runtime
check is used to determine if IRQ steer can be OFF before system
suspend.

If resources are powered off for suspend, they should be restored
properly after system resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Current implementation of i.MX8QM power management related
features does NOT optimize power number, all system resources
like CCI, DDR, and A cluster etc. are kept in STBY mode (powered
ON) when system suspend or CPU hotplug.

To lower the power number, OFF mode should be adopted for those
system resources whenever they can be OFF, A cluster will be OFF
if the CPUs in the cluster are all off line, DDR/MU/DB can be OFF
if system suspend, IRQ steer can be OFF if the wakeup source is
belonged to system controller partition, so wakeup source runtime
check is used to determine if IRQ steer can be OFF before system
suspend.

If resources are powered off for suspend, they should be restored
properly after system resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>

Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>

After the removal of deprecated interfaces in TF 2.0 the migration to
the new GIC driver interfaces was done incorrectly in rk3328 and rk3368:
2d6f1f01

 ("rockchip: Migrate to new interfaces").

In the GICv2 driver it is mandated that all interrupts are Group 0
interrupts. This patch simply moves all Group 1 interrupts to Group 0.

Change-Id: I224c0135603eb5b81bd512976361500c0d129a91
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch inits the GPIO in BL2 earlysetup. So BL2 can start operating
GPIO pins.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

Change-Id: I670ea80e0331c2d4b2ccfa563a45469a43f6902d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ia601d5ad65ab199e747fb60af4979b7db477d249
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ida5dae39478654405d0ee31a6cbddb4579e76a7f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Icc59cdaf2b56f6936e9847f1894594c671db2e94
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I656753a1825ea7340a3708b950fa6b57455e9056
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I8989d2aa0258bf3b50a856c5b81532d578600124
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The PLAT_XLAT_TABLES_DYNAMIC build option, defined in platform_def.h
in Arm platforms, is checked by several headers, affecting their
behaviour. To avoid issues around the include ordering of the headers,
the definition should be moved to the platform's makefile.

Change-Id: I0e12365c8d66309122e8a20790e1641a4f480a10
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Use full include paths like it is done for common includes.

This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.

Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

NXP's i.MX8QM uses Cortex-A53 r0p4, enable necessary
erratas for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

NXP's i.MX8MQ uses Cortex-A53 r0p4, enable necessary
erratas for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

This patch removes this unused config option from the Tegra186
platform makefiles.

Change-Id: Idcdf6854332a26599323a247289c2d3ce19f475f
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes the usage of this platform config, as it is always
enabled by all the supported platforms.

Change-Id: Ie7adb641adeb3604b177b6960b797722d60addfa
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a platform setup handler that gets called after
the MMU is enabled. Platforms wanting to make use of this handler
should declare 'plat_late_platform_setup' handler in their platform
files, to override the default weakly defined handler.

Change-Id: Ibc97a2e5a24608ddea856d0bd543a9d5876f604c
Signed-off-by: Dilan Lee <dilee@nvidia.com>

There are Tegra platforms which have limited UART ports and so
all the components have to share the console. The SPE helps out
by collecting all the logs in such cases and prints them on the
shared UART port.

This patch adds a driver to communicate with the SPE driver, which
in turn provides the console.

Change-Id: Ie750520b936b8bed0ab1d876f03fc0a3490a85a3
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch includes the console driver from individual platform
makefiles and removes it from tegra_common.mk. This allows future
platforms to include consoles of their choice.

Change-Id: I7506562bfac78421a80fb6782ac8472fbef6cfb0
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Tegra SoCs currently do not have a SMMU register at address 0xFFFFFFFF.
This patch changes the search criteria, to look for this marker, to
calculate the size of the saved context.

Change-Id: I15d91945ecb78267f91c45f37985dbb2327ca3ae
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The Tegra memctrl driver sets up the TZDRAM fence during boot and
system suspend exit. This patch provides individual platforms with
handlers to perform custom steps during TZDRAM setup.

Change-Id: Iee094d6ca189c6dd24f1147003c33c99ff3a953b
Signed-off-by: Steven Kao <skao@nvidia.com>

This patch adds support to save the system suspend entry and exit
markers to TZDRAM to help the trampoline code decide if the current
warmboot is actually an exit from System Suspend.

The Tegra186 platform handler sets the system suspend entry marker
before entering SC7 state and the trampoline flips the state back to
system resume, on exiting SC7.

Change-Id: I29d73f1693c89ebc8d19d7abb1df1e460eb5558e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a helper function to get the SMMU context's offset
and uses another helper function to get the CPU trampoline offset.
These helper functions are used by the System Suspend entry sequence
to save the SMMU context and CPU reset handler to TZDRAM.

Change-Id: I95e2862fe37ccad00fa48ec165c6e4024df01147
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch returns error if BPMP initialization fails. The platform
code marks the cluster as "runnning" since we wont be able to get
it into the low power state without BPMP.

Change-Id: I86f51d478626240bb7b4ccede8907674290c5dc1
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch renames all the secure scratch registers to reflect their
usage.

This is a list of all the macros being renamed:

- SECURE_SCRATCH_RSV1_* -> SCRATCH_RESET_VECTOR_*
- SECURE_SCRATCH_RSV6 -> SCRATCH_SECURE_BOOTP_FCFG
- SECURE_SCRATCH_RSV11_* -> SCRATCH_SMMU_TABLE_ADDR_*
- SECURE_SCRATCH_RSV53_* -> SCRATCH_BOOT_PARAMS_ADDR_*
- SECURE_SCRATCH_RSV55_* -> SCRATCH_TZDRAM_ADDR_*

NOTE: Future SoCs will have to define these macros to
      keep the drivers functioning.

Change-Id: Ib3ba40dd32e77b92b47825f19c420e6fdfa8b987
Signed-off-by: Steven Kao <skao@nvidia.com>