GitLab

All the m0 code run in SRAM before, but we need to watch PMU_POWER_ST
when SOC enter into FSM, and SRAM will shutdown during this time, so
this code need run in PMUSRAM. But PMUSRAM only 8K space, we can not
put all the m0 binary into PMUSRAM, Split the M0 binary into two, dram
part still run in SRAM, and suspend part run in PMUSRAM.

Change-Id: Ie08bdf3e2b8838f12b9297fe60ab0aad219684b1
Signed-off-by: Lin Huang <hl@rock-chips.com>

we need to enable PMU_WKUP_RST_EN for pmu powermode configure, since
enable wakeup reset will hold the soc status, so the SOC will not affect
by some power or other single glitch when resume, and keep the soc in the
right status. And it not need to enable DDRIO_RET_HW_DE_REQ, the ddr resume
will do it manual.

Change-Id: Ib4af897ffb3cb63dc2aa9a6002e5d9ef86ee4a49
Signed-off-by: Lin Huang <hl@rock-chips.com>

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size of BL31 has been increased in builds with SPM.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.

The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.

Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Since commit 031dbb12

 ("AArch32: Add essential Arch helpers"),
it is difficult to use consistent format strings for printf() family
between aarch32 and aarch64.

For example, uint64_t is defined as 'unsigned long long' for aarch32
and as 'unsigned long' for aarch64.  Likewise, uintptr_t is defined
as 'unsigned int' for aarch32, and as 'unsigned long' for aarch64.

A problem typically arises when you use printf() in common code.

One solution could be, to cast the arguments to a type long enough
for both architectures.  For example, if 'val' is uint64_t type,
like this:

  printf("val = %llx\n", (unsigned long long)val);

Or, somebody may suggest to use a macro provided by <inttypes.h>,
like this:

  printf("val = %" PRIx64 "\n", val);

But, both would make the code ugly.

The solution adopted in Linux kernel is to use the same typedefs for
all architectures.  The fixed integer types in the kernel-space have
been unified into int-ll64, like follows:

    typedef signed char           int8_t;
    typedef unsigned char         uint8_t;

    typedef signed short          int16_t;
    typedef unsigned short        uint16_t;

    typedef signed int            int32_t;
    typedef unsigned int          uint32_t;

    typedef signed long long      int64_t;
    typedef unsigned long long    uint64_t;

[ Linux commit: 0c79a8e29b5fcbcbfd611daf9d500cfad8370fcf ]

This gets along with the codebase shared between 32 bit and 64 bit,
with the data model called ILP32, LP64, respectively.

The width for primitive types is defined as follows:

                   ILP32           LP64
    int            32              32
    long           32              64
    long long      64              64
    pointer        32              64

'long long' is 64 bit for both, so it is used for defining uint64_t.
'long' has the same width as pointer, so for uintptr_t.

We still need an ifdef conditional for (s)size_t.

All 64 bit architectures use "unsigned long" size_t, and most 32 bit
architectures use "unsigned int" size_t.  H8/300, S/390 are known as
exceptions; they use "unsigned long" size_t despite their architecture
is 32 bit.

One idea for simplification might be to define size_t as 'unsigned long'
across architectures, then forbid the use of "%z" string format.
However, this would cause a distortion between size_t and sizeof()
operator.  We have unknowledge about the native type of sizeof(), so
we need a guess of it anyway.  I want the following formula to always
return 1:

  __builtin_types_compatible_p(size_t, typeof(sizeof(int)))

Fortunately, ARM is probably a majority case.  As far as I know, all
32 bit ARM compilers use "unsigned int" size_t.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Commit 4c0d0390

 ("Rework type usage in Trusted Firmware") changed
the type usage in struct declarations, but did not touch the definition
side.  Fix the type mismatch.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Fixes: f3d522be

 ("poplar: Support Trusted OS extra image (OP-TEE header) parsing")
Signed-off-by: Victor Chong <victor.chong@linaro.org>

SGI-575 platform is based on Cortex-A75 processor which has its MT bit
in the MPIDR register set to '1'. So the Arm platform layer code has
to be made aware of this.
Signed-off-by: Sudipto Paul <sudipto.paul@arm.com>

Currently the SCMI driver supports MHUv1, but Arm platforms may have
varied versions of MHU driver, with MHUv2 controllers being in the
latest Arm platforms.

This patch updates the SCMI driver to support MHUv2, specifically that
the sender must send the wake-up to the receiver before initiating any
data transfer.

Also, the existing mhu driver files, css_mhu.c and css_mhu.h, have been
moved from the scpi directory to a new directory, css/drivers/mhu.

Change-Id: I9b46b492a3e1d9e26db12d83a9773958a8c8402f
Signed-off-by: Samarth Parikh <samarth.parikh@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp SPD=tspd TRUSTED_BOARD_BOOT=1 \
	     GENERATE_COT=1 ARM_ROTPK_LOCATION=devel_rsa \
	     ROT_KEY=arm_rotprivk_rsa.pem MBEDTLS_DIR=mbedtls all

Change-Id: Ie4cd6011b3e4fdcdd94ccb97a7e941f3b5b7aeb8
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp SPD=tspd all

Change-Id: I0a16cf68fef29cf00ec0a52e47786f61d02ca4ae
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.3: All declarations of an object or function shall
          use the same names and type qualifiers.

Fixed for:
	make DEBUG=1 PLAT=juno LOG_LEVEL=50 all

Change-Id: I0e4a03a0d2170cb1c632e079112a972091994a39
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I32b223251b8bf5924149d89431a65d3405a73d3e
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Assert before actually using.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>

Clean cache to flush parameters into SRAM before MCU using them.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Store those DDR parameters into SRAM. They may be used by MCU
firmware.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Fix that DDR can't work at 533MHz. Now step to set DDR frequency
from 150MHz to 800MHz. DDR could work among these frequency, 150MHz,
266MHz, 400MHz, 533MHz and 800MHz.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Add TZMP1 support on Juno and increase the BL2 size accordingly due to the
extra data structures to describe the TZC regions and the additional code.
Signed-off-by: Summer Qin <summer.qin@arm.com>

This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.

This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>

This patch introduce TF-A support for NXP's ls1043a platform.
more details information of ls1043a chip and ls1043ardb board
can be found at docs/plat/ls1043a.rst.

Boot sequence on ls1043a is: bootrom loads bl1 firstly, then bl1
loads bl2, bl2 will load bl31, bl32 and bl33, bl31 will boot
bl32(tee os) and bl33(u-boot or uefi), bl33 boot Linux kernel.

Now TF-A on ls1043ardb platform has the following features in this patch:
	* Support boot from Nor flash.
	* TF-A can boot bl33 which runs in el2 of non-secure world.
	* TF-A boot OPTee OS.
	* Support PSCI
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Chenyin.Ha <Chenyin.Ha@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: jiaheng.fan <jiaheng.fan@nxp.com>
Signed-off-by: Wen He <wen.he_1@nxp.com>

Building TBBR(SPD=opteed) and non-TBBR TF-A images is breaking for
Juno for different configurations listed below:

* Overflow error of 4096 bytes for rsa algorithm.
* Overflow error of 8192 bytes for ecdsa algorithm.
* Overflow error of 4096 bytes for rsa+ecdsa algorithm.
* Overflow error of 4096 bytes for non-TBBR case.

So this patch increments macro PLAT_ARM_MAX_BL2_SIZE for all the above
cases accordingly.

Change-Id: I75ec6c0a718181d34553fe55437f0496f467683f
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>

This fixes an off by 576x bug the the sram_udelay code. The wrong
value was multipled by the system ticks per mhz value (which is 24),
so we delayed for 1/576th of the requested time.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The current AArch32 version of plat_arm_calc_core_pos uses an incorrect
algorithm to calculate the linear position of a core / PE from its
MPIDR.

This patch corrects the algorithm to:

(ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId

which supports cores where there are more than 1 PE per CPU.

NOTE: the AArch64 version was fixed in 39b21d19



Change-Id: I72aea89d8f72f8b1fef54e2177a0fa6fef0f5513
Signed-off-by: David Cunado <david.cunado@arm.com>

Use the console_pl011_core_* functions directly in the crash console
callbacks.

This bypasses the MULTI_CONSOLE_API for the crash console (UART1), but
allows using the crash console before the C runtime has been initialized
(eg to call ASM_ASSERT). This retains backwards compatibility with respect
to functionality when the old API is used.

Use the MULTI_CONSOLE_API to register UART0 as the boot and runtime
console.

Fixes ARM-software/tf-issues#572
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>

Add support for System Guidance for Infrastructure platform SGI575.

Change-Id: I0125c2ed4469fbc8367dafcc8adce770b6b3147d
Signed-off-by: Nariman Poushin <nariman.poushin@linaro.org>

If system is still accessing storage device, reboot operation
may cause data broken. So add the flush and delay operation
before system reset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Void pointers have been used to access linker symbols, by declaring an
extern pointer, then taking the address of it. This limits symbols
values to aligned pointer values. To remove this restriction an
IMPORT_SYM macro has been introduced, which declares it as a char
pointer and casts it to the required type.

Change-Id: I89877fc3b13ed311817bb8ba79d4872b89bfd3b0
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.

The crash console doesn't use this API, it uses internally the core
functions of the 16550 console.

`bl31_plat_runtime_setup` is no longer needed. When this platform port
was introduced, that function used to disable the console. It was needed
to override that behaviour. The new behaviour is to switch to the
runtime console. The console is registered for all scopes (boot, crash
and runtime) in `rpi3_console_init` so it is not needed to override the
default behaviour anymore.

Update documentation.

Change-Id: If2ee8f91044216183b7ef142e5c05ad6220ae92f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Ensure (where possible) that switch statements in plat comply with MISRA
rules 16.1 - 16.7.

Change-Id: Ie4a7d2fd10f6141c0cfb89317ea28a755391622f
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>

Removes fall-through in switch statement on unknown interrupt type in
release builds.

Previous behaviour was to assert(0) on default case in debug builds but
fall through and interpret the unknown interrupt type as
INTR_TYPE_EL3 in release builds.

Change-Id: I05fb0299608efda0f9eda2288d3e56e5625e05c9
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>

Add crash_console_init declaration to console.h
Only enable MULTI_CONSOLE_API for AArch64

Fixes ARM-software/tf-issues#571
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>

Add support for the new MULTI_CONSOLE_API

Crash information is now displayed in both the runtime and crash consoles,
if a crash occurs after the runtime console has been enabled

Enable MULTI_CONSOLE_API by default on qemu builds

Fixes ARM-software/tf-issues#561
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>

When the source code says 'SMCC' it is talking about the SMC Calling
Convention. The correct acronym is SMCCC. This affects a few definitions
and file names.

Some files have been renamed (smcc.h, smcc_helpers.h and smcc_macros.S)
but the old files have been kept for compatibility, they include the
new ones with an ERROR_DEPRECATED guard.

Change-Id: I78f94052a502436fdd97ca32c0fe86bd58173f2f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Allow qemu users to enable stack protection. Since the virt platform
does not provide an RNG, use a basic, timer-based, canary generation,
similarly to FVP.

Increase SRAM size and BL2 size to fit images when stack protection is
enabled.

Notice that stack protection is not enabled by default in qemu.

Fixes ARM-software/tf-issues#568
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>

there are two fix for save/restore watchdog register:
1. watchdog plck will shutdown after secure_watchdog_disable(), so need
   to save register before it and restore after secure_watchdog_enable().
2. need write 0x76 to cnt_restart to keep watchdog alive when restore
   watchdog register.

Change-Id: I1f6fbceae22186e3b72a87df6332a110adf37479
Signed-off-by: Lin Huang <hl@rock-chips.com>

x3 will be assigned by the folloing instructions.
So the first instruction is not needed any more.

old method:
  (ClusterId * FVP_MAX_CPUS_PER_CLUSTER)
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId

it should be
  (ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId

which can be simplified as:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER + CPUId) * FVP_MAX_PE_PER_CPU + ThreadId
Signed-off-by: Wang Feng <feng_feng.wang@spreadtrum.com>

Various changes to comply with MISRA static analysis rules
Signed-off-by: Jolly Shah <jollys@xilinx.com>

Existing database allows to set only single mode for SDIO.
SDIO can have different groups (8 bit, 4 bit and 1 bit).
As there is only single SDIO group in each pin, it is not
 possible to use different mode groups for SDIO.

Extend database in generic way to allow multiuple function
groups in single pin. Add different SDIO groups to pins and
create separate functions for each modes.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>

Add SMC call to query ATF PM version. This version
can be used by Linux to match with expected version.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>

With new EEMI APIs addition, version is updated to 1.0
Signed-off-by: Jolly Shah <jollys@xilinx.com>