GitLab

Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.

Change-Id: I7a23327394d142af4b293ea7ccd90b843c54587c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.

Change-Id: I07a07677153d3671ced776671e4f107824d3df16
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

*All* UART drivers in TF-A are storing their base address as a uintptr_t
pointer in the first location of the UART specific driver data.
Since the base address is a pretty natural and generic data item, we
should integrate this into the generic console_t structure.

That will not only allow to remove a lot of seemingly UART specific data
structures, but also enables to simplify runtime choices between different
UARTs, since they can share the same pointer.

This patch just adds the new member, the existing data structures will
be handled on a per-UART base in follow-up patches.

Change-Id: I59ce49471ccc8f3b870f2cfd8a72ebfd0cb14d12
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch introduces a build flag which allows the xlat tables
to be mapped in a read-only region within BL31 memory. It makes it
much harder for someone who has acquired the ability to write to
arbitrary secure memory addresses to gain control of the
translation tables.

The memory attributes of the descriptors describing the tables
themselves are changed to read-only secure data. This change
happens at the end of BL31 runtime setup. Until this point, the
tables have read-write permissions. This gives a window of
opportunity for changes to be made to the tables with the MMU on
(e.g. reclaiming init code). No changes can be made to the tables
with the MMU turned on from this point onwards. This change is also
enabled for sp_min and tspd.

To make all this possible, the base table was moved to .rodata. The
penalty we pay is that now .rodata must be aligned to the size of
the base table (512B alignment). Still, this is better than putting
the base table with the higher level tables in the xlat_table
section, as that would cost us a full 4KB page.

Changing the tables from read-write to read-only cannot be done with
the MMU on, as the break-before-make sequence would invalidate the
descriptor which resolves the level 3 page table where that very
descriptor is located. This would make the translation required for
writing the changes impossible, generating an MMU fault.

The caches are also flushed.
Signed-off-by: Petre-Ionut Tudor <petre-ionut.tudor@arm.com>
Change-Id: Ibe5de307e6dc94c67d6186139ac3973516430466

* changes:
  Tegra: spe: uninit console on a timeout
  Tegra: handler to check support for System Suspend
  Tegra: bpmp_ipc: improve cyclomatic complexity
  Tegra: platform handler to relocate BL32 image
  Tegra: common: improve cyclomatic complexity
  Tegra210: secure PMC hardware block
  Tegra: delay_timer: support for physical secure timer
  include: move MHZ_TICKS_PER_SEC to utils_def.h
  Tegra194: memctrl: lock mc stream id security config
  Tegra210: resume PMC hardware block for all platforms
  Tegra: macro for legacy WDT FIQ handling
  Tegra186: enable higher performance non-cacheable load forwarding
  Tegra210: enable higher performance non-cacheable load forwarding
  cpus: higher performance non-cacheable load forwarding

Till now TF-A allows limited number of external images to be made part
of FIP. With SPM coming along, there may exist multiple SP packages
which need to be inserted into FIP. To achieve this we need a more
scalable approach to feed SP packages to FIP.

This patch introduces changes in build system to generate and add SP
packages into FIP based on information provided by platform.
Platform provides information in form of JSON which contains layout
description of available Secure Partitions.
JSON parser script is invoked by build system early on and generates
a makefile which updates FIP, SPTOOL and FDT arguments which will be
used by build system later on for final packaging.

"SP_LAYOUT_FILE" passed as a build argument and can be outside of TF-A
tree. This option will be used only when SPD=spmd.

For each SP, generated makefile will have following entries
     - FDT_SOURCES	+=	sp1.dts
     - SPTOOL_ARGS	+= 	-i sp1.img:sp1.dtb -o sp1.pkg
     - FIP_ARGS		+=	--blob uuid=XXXX-XXX...,file=SP1.pkg
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ib6a9c064400caa3cd825d9886008a3af67741af7

There are chances a denial-of-service attack, if an attacker
removes the SPE firmware from the system. The console driver
would end up waiting for the firmware to respond indefinitely.
The console driver must detect such scenarios and uninit the
interface as a result.

This patch adds a timeout to the interaction with the SPE
firmware and uninits the interface if it times out.

Change-Id: I06f27a858baed25711d41105b4110865f1a01727
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Tegra210 SoCs need the sc7entry-fw to enter System Suspend mode,
but there might be certain boards that do not have this firmware
blob. To stop the NS world from issuing System suspend entry
commands on such devices, we ned to disable System Suspend from
the PSCI "features".

This patch removes the System suspend handler from the Tegra PSCI
ops, so that the framework will disable support for "System Suspend"
from the PSCI "features".

Original change by: kalyani chidambaram <kalyanic@nvidia.com>

Change-Id: Ie029f82f55990a8b3a6debb73e95e0e218bfd1f5
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Code complexity is a good indication of maintainability versus
testability of a piece of software.

ISO26262 introduces the following thresholds:

    complexity < 10 is accepted
    10 <= complexity < 20 has to be justified
    complexity >= 20 cannot be accepted

Rationale is that number of test cases to fully test a piece of
software can (depending on the coverage metrics) grow exponentially
with the number of branches in the software.

This patch removes redundant conditionals from 'ipc_send_req_atomic'
handler to reduce the McCabe Cyclomatic Complexity for this function

Change-Id: I20fef79a771301e1c824aea72a45ff83f97591d5
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch provides platforms an opportunity to relocate the
BL32 image, during cold boot. Tegra186 platforms, for example,
relocate BL32 images to TZDRAM memory as the previous bootloader
relies on BL31 to do so.

Change-Id: Ibb864901e43aca5bf55d8c79e918b598c12e8a28
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Code complexity is a good indication of maintainability versus
testability of a piece of software.

ISO26262 introduces the following thresholds:

    complexity < 10 is accepted
    10 <= complexity < 20 has to be justified
    complexity >= 20 cannot be accepted

Rationale is that number of test cases to fully test a piece of
software can (depending on the coverage metrics) grow exponentially
with the number of branches in the software.

This patch removes redundant conditionals from 'bl31_early_platform_setup'
handler to reduce the McCabe Cyclomatic Complexity for this function.

Change-Id: Ifb628e33269b388f9323639cd97db761a7e049c4
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch sets the "secure" bit to mark the PMC hardware block
as accessible only from the secure world. This setting must be
programmed during cold boot and System Resume.

The sc7entry-fw, running on the COP, needs access to the PMC block
to enter System Suspend state, so "unlock" the PMC block before
passing control to the COP.

Change-Id: I00e39a49ae6b9f8c8eafe0cf7ff63fe6a67fdccf
Signed-off-by: kalyani chidambaram <kalyanic@nvidia.com>

This patch modifies the delay timer driver to switch to the ARM
secure physical timer instead of using Tegra's on-chip uS timer.

The secure timer is not accessible to the NS world and so eliminates
an important attack vector, where the Tegra timer source gets switched
off from the NS world leading to a DoS attack for the trusted world.

This timer is shared with the S-EL1 layer for now, but later patches
will mark it as exclusive to the EL3 exception mode.

Change-Id: I2c00f8cb4c48b25578971c626c314603906ad7cc
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch moves the MHZ_TICKS_PER_SEC macro to utils_def.h
for other platforms to use.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I6c4dc733f548d73cfdb3515ec9ad89a9efaf4407

This patch locks most of the stream id security config registers as
per HW guidance.

This patch keeps the stream id configs unlocked for the following
clients, to allow some platforms to still function, until they make
the transition to the latest guidance.

- ISPRA
- ISPFALR
- ISPFALW
- ISPWA
- ISPWA1
- ISPWB
- XUSB_DEVR
- XUSB_DEVW
- XUSB_HOSTR
- XUSB_HOSTW
- VIW
- VIFALR
- VIFALW

Change-Id: I66192b228a0a237035938f498babc0325764d5df
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>

The PMC hardware block resume handler was called for Tegra210
platforms, only if the sc7entry-fw was present on the device.
This would cause problems for devices that do not support this
firmware.

This patch fixes this logic and resumes the PMC block even if
the sc7entry-fw is not present on the device.

Change-Id: I6f0eb7878126f624ea98392f583ed45a231d27db
Signed-off-by: Kalyani Chidambaram <kalyanic@nvidia.com>

This patch adds the macro to enable legacy FIQ handling to the common
Tegra makefile. The default value of this macro is '0'. Platforms that
need this support should enable it from their makefiles.

This patch also helps fix violation of Rule 20.9.

Rule 20.9 "All identifiers used in the controlling expression of #if
           of #elif preprocessing directives shall be #define'd before
           evaluation"

Change-Id: I4f0c9917c044b5b1967fb5e79542cd3bf6e91f18
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch enables higher performance non-cacheable load forwarding for
Tegra186 platforms.

Change-Id: Ifceb304bfbd805f415bb6205c9679602ecb47b53
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch enables higher performance non-cacheable load forwarding for
Tegra210 platforms.

Change-Id: I11d0ffc09aca97d37386f283f2fbd2483d51fd28
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The CPUACTLR_EL1 register on Cortex-A57 CPUs supports a bit to enable
non-cacheable streaming enhancement. Platforms can set this bit only
if their memory system meets the requirement that cache line fill
requests from the Cortex-A57 processor are atomic.

This patch adds support to enable higher performance non-cacheable load
forwarding for such platforms. Platforms must enable this support by
setting the 'A57_ENABLE_NONCACHEABLE_LOAD_FWD' flag from their
makefiles. This flag is disabled by default.

Change-Id: Ib27e55dd68d11a50962c0bbc5b89072208b4bac5
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Removed duplicate error code present for SMCCC and used
proper error code for "SMCCC_ARCH_WORKAROUND_2" call.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I76fc7c88095f78a7e2c3d205838f8eaf3132ed5c

Fix mailbox driver incompatible cast bug and control flow issue that
was flagged by Coverity Scan.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I3f34e98d24e40139d31cf7d5b9b973cd2d981065

* changes:
  rcar_gen3: plat: Minor coding style fix for rcar_version.h
  rcar_gen3: plat: Update IPL and Secure Monitor Rev.2.0.6
  rcar_gen3: drivers: ddr: Update DDR setting for H3, M3, M3N
  rcar_gen3: drivers: ddr: Update DDR setting for H3, M3, M3N
  rcar_gen3: drivers: board: Add new board revision for M3ULCB
  rcar_gen3: drivers: ddr: Update DDR setting for H3, M3, M3N
  rcar_gen3: plat: Update IPL and Secure Monitor Rev.2.0.5
  rcar_gen3: plat: Change fixed destination address of BL31 and BL32