GitLab

Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.

Change-Id: I7a23327394d142af4b293ea7ccd90b843c54587c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch introduces a build flag which allows the xlat tables
to be mapped in a read-only region within BL31 memory. It makes it
much harder for someone who has acquired the ability to write to
arbitrary secure memory addresses to gain control of the
translation tables.

The memory attributes of the descriptors describing the tables
themselves are changed to read-only secure data. This change
happens at the end of BL31 runtime setup. Until this point, the
tables have read-write permissions. This gives a window of
opportunity for changes to be made to the tables with the MMU on
(e.g. reclaiming init code). No changes can be made to the tables
with the MMU turned on from this point onwards. This change is also
enabled for sp_min and tspd.

To make all this possible, the base table was moved to .rodata. The
penalty we pay is that now .rodata must be aligned to the size of
the base table (512B alignment). Still, this is better than putting
the base table with the higher level tables in the xlat_table
section, as that would cost us a full 4KB page.

Changing the tables from read-write to read-only cannot be done with
the MMU on, as the break-before-make sequence would invalidate the
descriptor which resolves the level 3 page table where that very
descriptor is located. This would make the translation required for
writing the changes impossible, generating an MMU fault.

The caches are also flushed.
Signed-off-by: Petre-Ionut Tudor <petre-ionut.tudor@arm.com>
Change-Id: Ibe5de307e6dc94c67d6186139ac3973516430466

The new API becomes the default one.

Change-Id: Ic1d602da3dff4f4ebbcc158b885295c902a24fec
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

Many parts of the code were duplicating symbols that are defined in
include/common/bl_common.h. It is better to only use the definitions in
this header.

As all the symbols refer to virtual addresses, they have to be
uintptr_t, not unsigned long. This has also been fixed in bl_common.h.

Change-Id: I204081af78326ced03fb05f69846f229d324c711
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Use full include paths like it is done for common includes.

This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.

Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Corrects typos in core code, documentation files, drivers, Arm
platforms and services.

None of the corrections affect code; changes are limited to comments
and other documentation.

Change-Id: I5c1027b06ef149864f315ccc0ea473e2a16bfd1d
Signed-off-by: Paul Beesley <paul.beesley@arm.com>

From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.

This also prevents problems like cyclic dependencies.

Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This function is not related to Arm platforms and can be reused by other
platforms if needed.

Change-Id: Ia9c328ce57ce7e917b825a9e09a42b0abb1a53e8
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

TF won't build since no memory region is specified
for when SEPARATE_CODE_AND_RODATA=0 it still relies on
the ARM_MAP_BL_RO_DATA region which is never defined for
this case. Create memory region combining code and RO data for
when the build flag SEPARATE_CODE_AND_RODATA=0 to fix this

Change-Id: I6c129eb0833497710cce55e76b8908ce03e0a638
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Change arm_setup_page_tables() to take a variable number of memory
regions. Remove coherent memory region from BL1, BL2 and BL2U as
their coherent memory region doesn't contain anything and
therefore has a size of 0. Add check to ensure this
doesn't change without us knowing.

Change-Id: I790054e3b20b056dda1043a4a67bd7ac2d6a3bc0
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size reserved for BL2 has been increased.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This reverts commit 2f18aa1f

.

It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.

Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size of BL31 has been increased in builds with SPM.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This fix modifies the order of #includes in ARM standard platforms
to meet the ARM TF coding standard.

Change-Id: Ide19aad6233babda4eea2d17d49e523645fed1b2
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

We have lots of duplicated defines (and comment blocks too).
Move them to include/plat/common/common_def.h.

While we are here, suffix the end address with _END instead of
_LIMIT.  The _END is a better fit to indicate the linker-derived
real end address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The usage of _LIMIT seems odd here, so rename as follows:
  BL_CODE_LIMIT     --> BL_CODE_END
  BL_RO_DATA_LIMIT  --> BL_RO_DATA_END
  BL1_CODE_LIMIT    --> BL1_CODE_END
  BL1_RO_DATA_LIMIT --> BL1_RO_DATA_END

Basically, we want to use _LIMIT and _END properly as follows:
  *_SIZE + *_MAX_SIZE = *_LIMIT
  *_SIZE + *_SIZE     = *_END

The _LIMIT is generally defined by platform_def.h to indicate the
platform-dependent memory constraint.  So, its typical usage is
  ASSERT(. <= BL31_LIMIT, "BL31 image has exceeded its limit.")
in a linker script.

On the other hand, _END is used to indicate the end address of the
compiled image, i.e. we do not know it until the image is linked.

Here, all of these macros belong to the latter, so should be
suffixed with _END.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The arm_setup_page_tables() function used to expect a single set of
addresses defining the extents of the whole read-only section, code
and read-only data mixed up, which was mapped as executable.

This patch changes this behaviour. arm_setup_page_tables() now
expects 2 separate sets of addresses:

 - the extents of the code section;
 - the extents of the read-only data section.

The code is mapped as executable, whereas the data is mapped as
execute-never. New #defines have been introduced to identify the
extents of the code and the read-only data section. Given that
all BL images except BL1 share the same memory layout and linker
script structure, these #defines are common across these images.
The slight memory layout differences in BL1 have been handled by
providing values specific to BL1.

Note that this patch also affects the Xilinx platform port, which
uses the arm_setup_page_tables() function. It has been updated
accordingly, such that the memory mappings on this platform are
unchanged. This is achieved by passing null values as the extents
of the read-only data section so that it is ignored. As a result,
the whole read-only section is still mapped as executable.

Fixes ARM-software/tf-issues#85

Change-Id: I1f95865c53ce6e253a01286ff56e0aa1161abac5

This patch introduces the arm_setup_page_tables() function to
set up page tables on ARM platforms. It replaces the
arm_configure_mmu_elx() functions and does the same thing except
that it doesn't enable the MMU at the end. The idea is to reduce
the amount of per-EL code that is generated by the C preprocessor
by splitting the memory regions definitions and page tables creation
(which is generic) from the MMU enablement (which is the only per-EL
configuration).

As a consequence, the call to the enable_mmu_elx() function has been
moved up into the plat_arch_setup() hook. Any other ARM standard
platforms that use the functions `arm_configure_mmu_elx()` must be
updated.

Change-Id: I6f12a20ce4e5187b3849a8574aac841a136de83d

This patch removes the dash character from the image name, to
follow the image terminology in the Trusted Firmware Wiki page:

    https://github.com/ARM-software/arm-trusted-firmware/wiki

Changes apply to output messages, comments and documentation.

non-ARM platform files have been left unmodified.

Change-Id: Ic2a99be4ed929d52afbeb27ac765ceffce46ed76

Suport for ARM GIC v2.0 and v3.0 drivers has been reworked to create three
separate drivers instead of providing a single driver that can work on both
versions of the GIC architecture. These drivers correspond to the following
software use cases:

1. A GICv2 only driver that can run only on ARM GIC v2.0 implementations
   e.g. GIC-400

2. A GICv3 only driver that can run only on ARM GIC v3.0 implementations
   e.g. GIC-500 in a mode where all interrupt regimes use GICv3 features

3. A deprecated GICv3 driver that operates in legacy mode. This driver can
   operate only in the GICv2 mode in the secure world. On a GICv3 system, this
   driver allows normal world to run in either GICv3 mode (asymmetric mode)
   or in the GICv2 mode. Both modes of operation are deprecated on GICv3
   systems.

ARM platforms implement both versions of the GIC architecture. This patch adds a
layer of abstraction to help ARM platform ports chose the right GIC driver and
corresponding platform support. This is as described below:

1. A set of ARM common functions have been introduced to initialise the GIC and
   the driver during cold and warm boot. These functions are prefixed as
   "plat_arm_gic_". Weak definitions of these functions have been provided for
   each type of driver.

2. Each platform includes the sources that implement the right functions
   directly into the its makefile. The FVP can be instantiated with different
   versions of the GIC architecture. It uses the FVP_USE_GIC_DRIVER build option
   to specify which of the three drivers should be included in the build.

3. A list of secure interrupts has to be provided to initialise each of the
  three GIC drivers. For GIC v3.0 the interrupt ids have to be further
  categorised as Group 0 and Group 1 Secure interrupts. For GIC v2.0, the two
  types are merged and treated as Group 0 interrupts.

  The two lists of interrupts are exported from the platform_def.h. The lists
  are constructed by adding a list of board specific interrupt ids to a list of
  ids common to all ARM platforms and Compute sub-systems.

This patch also makes some fields of `arm_config` data structure in FVP redundant
and these unused fields are removed.

Change-Id: Ibc8c087be7a8a6b041b78c2c3bd0c648cd2035d8

This patch migrates ARM reference platforms, Juno and FVP, to the new platform
API mandated by the new PSCI power domain topology and composite power state
frameworks. The platform specific makefiles now exports the build flag
ENABLE_PLAT_COMPAT=0 to disable the platform compatibility layer.

Change-Id: I3040ed7cce446fc66facaee9c67cb54a8cd7ca29

This major change pulls out the common functionality from the
FVP and Juno platform ports into the following categories:

*   (include/)plat/common. Common platform porting functionality that
typically may be used by all platforms.

*   (include/)plat/arm/common. Common platform porting functionality
that may be used by all ARM standard platforms. This includes all
ARM development platforms like FVP and Juno but may also include
non-ARM-owned platforms.

*   (include/)plat/arm/board/common. Common platform porting
functionality for ARM development platforms at the board
(off SoC) level.

*   (include/)plat/arm/css/common. Common platform porting
functionality at the ARM Compute SubSystem (CSS) level. Juno
is an example of a CSS-based platform.

*   (include/)plat/arm/soc/common. Common platform porting
functionality at the ARM SoC level, which is not already defined
at the ARM CSS level.

No guarantees are made about the backward compatibility of
functionality provided in (include/)plat/arm.

Also remove any unnecessary variation between the ARM development
platform ports, including:

*   Unify the way BL2 passes `bl31_params_t` to BL3-1. Use the
Juno implementation, which copies the information from BL2 memory
instead of expecting it to persist in shared memory.

*   Unify the TZC configuration. There is no need to add a region
for SCP in Juno; it's enough to simply not allow any access to
this reserved region. Also set region 0 to provide no access by
default instead of assuming this is the case.

*   Unify the number of memory map regions required for ARM
development platforms, although the actual ranges mapped for each
platform may be different. For the FVP port, this reduces the
mapped peripheral address space.

These latter changes will only be observed when the platform ports
are migrated to use the new common platform code in subsequent
patches.

Change-Id: Id9c269dd3dc6e74533d0e5116fdd826d53946dc8