GitLab

spd: tlkd: support for "NS memory ranges" function ID

Add documentation about plat_try_next_boot_source to bl1_platform_setup

uniphier: clean-up platform makefile

AMU: Remove unnecessary WARN()

If AMU is not supported by the hardware but it is enabled in Trusted
Firmware, the console will be spammed with warnings every time a CPU
is brought up with a CPU ON call.

Remove the warning message as this is more in line with how other
extensions like SPE and SVE are handled.

Change-Id: Iba6d367e4d1375ab554d23d2eaceab3ae1362c5a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

AMUv1 support

Workarounds for CVE-2017-5715 on Cortex A57/A72/A73 and A75

Increase BL31 memory space by 2 pages

On some build configurations BL31 is running out of space.  Now that
TSP is moved to secure dram, we have a bit of additional space to use
in BL31.

Change-Id: Ib89fcd8bae99c85c9c5e5d9228bb42fb7048dcb6
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Signed-off-by: David Cunado <david.cunado@arm.com>

Change-Id: I504d3f65ca5829bc1f4ebadb764931f8379ee81f
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

On some systems, the AMU counters might reset to 0 when a CPU
powerdown happens.  This behaviour conflicts with the intended
use-case of AMU as lower ELs are only expected to see non-decreasing
counter values.

Change-Id: If25519965d4e6e47e09225d0e732947986cbb5ec
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Add some AMU helper functions to allow configuring, reading and
writing of the Group 0 and Group 1 counters.  Documentation for these
helpers will come in a separate patch.

Change-Id: I656e070d2dae830c22414f694aa655341d4e2c40
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

A new platform macro `PLAT_AMU_GROUP1_COUNTERS_MASK` controls which
group 1 counters should be enabled. The maximum number of group 1
counters supported by AMUv1 is 16 so the mask can be at most 0xffff.
If the platform does not define this mask, no group 1 counters are
enabled.

A related platform macro `PLAT_AMU_GROUP1_NR_COUNTERS` is used by
generic code to allocate an array to save and restore the counters on
CPU suspend.

Change-Id: I6d135badf4846292de931a43bb563077f42bb47b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

The suspend hook is published at the start of a CPU powerdown
operation.  The resume hook is published at the end of a CPU powerup
operation.

Change-Id: I50c05e2dde0d33834095ac41b4fcea4c161bb434
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

If the CSV2 field reads as 1 then branch targets trained in one
context cannot affect speculative execution in a different context.
In that case skip the workaround on Cortex A75.

Change-Id: I4d5504cba516a67311fb5f0657b08f72909cbd38
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Invalidate the Branch Target Buffer (BTB) on entry to EL3 by
temporarily dropping into AArch32 Secure-EL1 and executing the
`BPIALL` instruction.

This is achieved by using 3 vector tables.  There is the runtime
vector table which is used to handle exceptions and 2 additional
tables which are required to implement this workaround.  The
additional tables are `vbar0` and `vbar1`.

The sequence of events for handling a single exception is
as follows:

1) Install vector table `vbar0` which saves the CPU context on entry
   to EL3 and sets up the Secure-EL1 context to execute in AArch32 mode
   with the MMU disabled and I$ enabled.  This is the default vector table.

2) Before doing an ERET into Secure-EL1, switch vbar to point to
   another vector table `vbar1`.  This is required to restore EL3 state
   when returning from the workaround, before proceeding with normal EL3
   exception handling.

3) While in Secure-EL1, the `BPIALL` instruction is executed and an
   SMC call back to EL3 is performed.

4) On entry to EL3 from Secure-EL1, the saved context from step 1) is
   restored.  The vbar is switched to point to `vbar0` in preparation to
   handle further exceptions.  Finally a branch to the runtime vector
   table entry is taken to complete the handling of the original
   exception.

This workaround is enabled by default on the affected CPUs.

NOTE
====

There are 4 different stubs in Secure-EL1.  Each stub corresponds to
an exception type such as Sync/IRQ/FIQ/SError.  Each stub will move a
different value in `R0` before doing an SMC call back into EL3.
Without this piece of information it would not be possible to know
what the original exception type was as we cannot use `ESR_EL3` to
distinguish between IRQs and FIQs.

Change-Id: I90b32d14a3735290b48685d43c70c99daaa4b434
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Invalidate the Branch Target Buffer (BTB) on entry to EL3 by disabling
and enabling the MMU.  To achieve this without performing any branch
instruction, a per-cpu vbar is installed which executes the workaround
and then branches off to the corresponding vector entry in the main
vector table.  A side effect of this change is that the main vbar is
configured before any reset handling.  This is to allow the per-cpu
reset function to override the vbar setting.

This workaround is enabled by default on the affected CPUs.

Change-Id: I97788d38463a5840a410e3cea85ed297a1678265
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

plat: xilinx: Add ZynqMP IPI mailbox service [v4]

If boot redundancy is required in BL1 then the initialization
of the boot sequence must be done in bl1_platform_setup. In BL2,
we had to add a new function, bl2_preload_setup, because
bl2_platform_setup is called after the images are loaded, making it
invalid for the boot sequence initialization.

Change-Id: I5c177ff142608ed38b4192288b06614343b2b83b
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Build: trivial fixes

hikey960: set isp clks as unsecure mode

Set alignment size to 512B for Hikey/Hikey960

Use zynqmp_ipi APIs to access IPI registers in pm_service.
As the zynqmp_ipi APIs doesn't cover IPI buffers, the pm_ipi
in pm_service will still directly access the IPI buffers.
Signed-off-by: Wendy Liang <jliang@xilinx.com>

Add IPI mailbox service to manage Xilinx ZynqMP IPI(Inter Processors
Interrupt) access.
Signed-off-by: Wendy Liang <jliang@xilinx.com>

Previously, ZynqMP IPI in ATF is only for ZynqMP PM,
This patch is to have a ZynqMP IPI implementation to handle
both ZynqMP PM IPI requirement and IPI mailbox service requirement
which will be introduced next.

We control IPI agents registers access but not IPI buffers access in
this implementation. Each IPI mailbox user will directly access the
IPI buffers.
Signed-off-by: Wendy Liang <jliang@xilinx.com>

This patch adds support to receive function ID with NS world's
memory ranges to provide the memory snapshot to TLK.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

SPM: Allow secondary CPUs to use the Secure Partition

The Secure Partition should be able to be used from any CPU, not just
the lead one. This patch point the secure contexts of all secondary
CPUs to the same one used by the lead CPU for the Secure Partition. This
way, they can also use it.

In order to prevent more than one CPU from using the Secure Partition at
the same time, a lock has been added.

Change-Id: Ica76373127c3626498b06c558a4874ce72201ff7
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Whether a Secure Partition is being initialized or not is something
related to that specific partition, so it should be saved with the
rest of the information related to it.

Change-Id: Ie8a780f70df83fb03ef9c01ba37960208d9b5319
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

It is not necessary to read data from stdin.  The input file name
is ripped off by -n option, anyway.  I still use the redirect for
the output to specify the output file name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add padding at the end of the last entry

Update dependencies for ARM TF

Change-Id: I2e29a63f08aed3b8ea0bb10170a3d55b8d033e62
Signed-off-by: Jett Zhou <jett.zhou@arm.com>
Signed-off-by: David Cunado <david.cunado@arm.com>

This patch adds padding bytes at the end of the last image in the
fip to be able to transfer by DMA the last image.

Change-Id: I8c6f07dee389cb3d1dc919936d9d52841d7e5723
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Signed-off-by: David Cunado <david.cunado@arm.com>

Move TSP to TZC secured DRAM

To allow BL31 to grow in SRAM, move TSP in TZC secured DRAM
by default.

Increase the BL31 max limit by one page.

Change-Id: Idd3479be02f0f9bafac2f275376d7db0c2015431
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

uniphier: a bundle of fixes

check_* targets just check necessary command line argument, not
build any images.  They should be specified as .PHONY.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM platforms: Allow platforms to define SDEI events

Commit 8f0617ef

 ("Apply TBBR naming convention to the fip_create
options") changed fiptool command options.  We often forget to update
documentation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>