GitLab

RD-N1-Edge based platforms can operate in dual-chip configuration
wherein two rdn1edge SoCs are connected through a high speed coherent
CCIX link.

This patch adds a function to check if the RD-N1-Edge platform is
operating in multi-chip mode by reading the SID register's NODE_ID
value. If operating in multi-chip mode, initialize GIC-600 multi-chip
operation by overriding the default GICR frames with array of GICR
frames and setting the chip 0 as routing table owner.

The address space of the second RD-N1-Edge chip (chip 1) starts from the
address 4TB. So increase the physical and virtual address space size to
43 bits to accommodate the multi-chip configuration. If the multi-chip
mode configuration is detected, dynamically add mmap entry for the
peripherals memory region of the second RD-N1-Edge SoC. This is required
to let the BL31 platform setup stage to configure the devices in the
second chip.

PLATFORM_CORE_COUNT macro is set to be multiple of CSS_SGI_CHIP_COUNT
and topology changes are added to represent the dual-chip configuration.

In order the build the dual-chip platform, CSS_SGI_CHIP_COUNT macro
should be set to 2:
export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all

Change-Id: I576cdaf71f0b0e41b9a9181fa4feb7091f8c7bb4
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.

Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

AFF3 bits of MPIDR corresponds to Chip-Id in Arm multi-chip platforms.
For calculating linear core position of CPU cores from slave chips, AFF3
bits has to be used. Update `plat_arm_calc_core_pos` assembly function
to include AFF3 bits in calculation.

Change-Id: I4af2bd82ab8e31e18bc61de22705a73893954260
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

Some of the Reference Design platforms like RD-N1-Edge can operate in
multi-chip configuration wherein two or more SoCs are connected through
a high speed coherent CCIX link. For the RD platforms, the remote chip
address space is at the offset of 4TB per chip. In order for the primary
chip to access the device memory region on the remote chip, the required
memory region entries need to be added as mmap entry. This patch adds
macros related to the remote chip device memory region.

Change-Id: I833810b96f1a0e7c3c289ac32597b6ba03344c80
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

Multi-chip platforms have two or more identical chips connected using a
high speed coherent link. In order to identify such platforms,
add chip_id and multi_chip_mode information in the platform variant
info structure. The values of these two new elements is populated
during boot.

Change-Id: Ie6e89cb33b3f0f408814f6239cd06647053e23ed
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

For SGI-575 and RD platforms, move bl31_platform_setup handler to
individual board files to allow the platforms to perform board specific
bl31 setup.

Change-Id: Ia44bccc0a7f40a155b33909bcb438a0909b20d42
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

Introduce macro 'CSS_SGI_CHIP_COUNT' to allow Arm CSS platforms with
multi-chip support to define number of chiplets on the platform. By
default, this flag is set to 1 and does not affect the existing single
chip platforms.

For multi-chip platforms, override the default value of
CSS_SGI_CHIP_COUNT with the number of chiplets supported on the
platform. As an example, the command below sets the number of chiplets
to two on the RD-N1-Edge multi-chip platform:

export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all

Change-Id: If364dc36bd34b30cc356f74b3e97633933e6c8ee
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

The platform topology description of the upcoming Arm's RD platforms
have different topology than those listed in the sgi_topology.c file. So
instead of adding platform specific topology into existing
sgi_topology.c file, those can be added to respective board files. In
order to maintain consistency with the upcoming platforms, move the
existing platform topology description to respective board files.

Change-Id: I4689c7d24cd0c75a3dc234370c34a85c08598abb
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

The contents of this header have been merged into the spm_mm_svc.h
header file.

Change-Id: I01530b2e4ec1b4c091ce339758025e2216e740a4
Signed-off-by: Paul Beesley <paul.beesley@arm.com>

Change-Id: I91c192924433226b54d33e57d56d146c1c6df81b
Signed-off-by: Paul Beesley <paul.beesley@arm.com>

Before adding any new SPM-related components we should first do
some cleanup around the existing SPM-MM implementation. The aim
is to make sure that any SPM-MM components have names that clearly
indicate that they are MM-related. Otherwise, when adding new SPM
code, it could quickly become confusing as it would be unclear to
which component the code belongs.

The secure_partition.h header is a clear example of this, as the
name is generic so it could easily apply to any SPM-related code,
when it is in fact SPM-MM specific.

This patch renames the file and the two structures defined within
it, and then modifies any references in files that use the header.

Change-Id: I44bd95fab774c358178b3e81262a16da500fda26
Signed-off-by: Paul Beesley <paul.beesley@arm.com>

The Secure Partition Manager (SPM) prototype implementation is
being removed. This is preparatory work for putting in place a
dispatcher component that, in turn, enables partition managers
at S-EL2 / S-EL1.

This patch removes:

- The core service files (std_svc/spm)
- The Resource Descriptor headers (include/services)
- SPRT protocol support and service definitions
- SPCI protocol support and service definitions

Change-Id: Iaade6f6422eaf9a71187b1e2a4dffd7fb8766426
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>

There are two different implementations of Secure Partition
management in TF-A. One is based on the "Management Mode" (MM)
design, the other is based on the Secure Partition Client Interface
(SPCI) specification. Currently there is a dependency between their
build flags that shouldn't exist, making further development
harder than it should be. This patch removes that
dependency, making the two flags function independently.

Before: ENABLE_SPM=1 is required for using either implementation.
        By default, the SPCI-based implementation is enabled and
        this is overridden if SPM_MM=1.

After: ENABLE_SPM=1 enables the SPCI-based implementation.
       SPM_MM=1 enables the MM-based implementation.
       The two build flags are mutually exclusive.

Note that the name of the ENABLE_SPM flag remains a bit
ambiguous - this will be improved in a subsequent patch. For this
patch the intention was to leave the name as-is so that it is
easier to track the changes that were made.

Change-Id: I8e64ee545d811c7000f27e8dc8ebb977d670608a
Signed-off-by: Paul Beesley <paul.beesley@arm.com>

NOTE: __ASSEMBLY__ macro is now deprecated in favor of __ASSEMBLER__.

All common C compilers predefine a macro called __ASSEMBLER__ when
preprocessing a .S file. There is no reason for TF-A to define it's own
__ASSEMBLY__ macro for this purpose instead. To unify code with the
export headers (which use __ASSEMBLER__ to avoid one extra dependency),
let's deprecate __ASSEMBLY__ and switch the code base over to the
predefined standard.

Change-Id: Id7d0ec8cf330195da80499c68562b65cb5ab7417
Signed-off-by: Julius Werner <jwerner@chromium.org>

The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.

So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.

Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Improved support for W=1 compilation flag by solving missing-prototypes
and old-style-definition warnings.

The libraries are compiling with warnings (which turn into errors with
the Werror flag).

Outside of libraries, some warnings cannot be fixed without heavy
structural changes.

Change-Id: I1668cf99123ac4195c2a6a1d48945f7a64c67f16
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

Replace all uses of 'SGI_CLARK' with 'RD_N1E1_EDGE' and
'SGI_CLARK_HELIOS' with 'RD_E1_EDGE' as per the updated product
names

Change-Id: Ib8136e421b1a46da1e5df58c6b1432d5c78d279b
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

Change-Id: Ideb49011da35f39ff1959be6f5015fa212ca2b6b
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

Many parts of the code were duplicating symbols that are defined in
include/common/bl_common.h. It is better to only use the definitions in
this header.

As all the symbols refer to virtual addresses, they have to be
uintptr_t, not unsigned long. This has also been fixed in bl_common.h.

Change-Id: I204081af78326ced03fb05f69846f229d324c711
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I656753a1825ea7340a3708b950fa6b57455e9056
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I8989d2aa0258bf3b50a856c5b81532d578600124
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Use full include paths like it is done for common includes.

This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.

Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

On ARM platforms, the BL2 memory can be overlaid by BL31/BL32. The memory
descriptors describing the list of executable images are created in BL2
R/W memory, which could be possibly corrupted later on by BL31/BL32 due
to overlay. This patch creates a reserved location in SRAM for these
descriptors and are copied over by BL2 before handing over to next BL
image.

Also this patch increases the PLAT_ARM_MAX_BL2_SIZE for juno when TBBR
is enabled.

Fixes ARM-Software/tf-issues#626

Change-Id: I755735706fa702024b4032f51ed4895b3687377f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.

This also prevents problems like cyclic dependencies.

Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The definitions in bl1/bl1_private.h and bl2/bl2_private.h are useful for
platforms that may need to access them.

Change-Id: Ifd1880f855ddafcb3bfcaf1ed4a4e0f121eda174
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Update some asserts that refer to #defines that only occur in
ARM platforms, preventing this code to be used on other platforms.
Instead, use a platform agnostic name, and update all the existing
users.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>

The top level makefile defines the PLAT variable, not PLATFORM.
This mistake was causing an empty variable expansion and showing an
incomplete error message.

Change-Id: I5da1275c73c61a7c1823643a76300f255841719d
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

For SGI-Clark.Helios platform, at present, only the CPU power ON/OFF
ops are supported. So override the PSCI ops to allow callbacks only
for CPU power ON/OFF operations.

Change-Id: Idc0a3deb78cb850310cbe849d77604fa9881579c
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

SGI-Clark.Helios platform is based on multi-threaded CPUs and uses an
additional thread power domain level as well.

Define a power domain tree descriptor 'sgi_clark_helios_pd_tree_desc'
for SGI-Clark.Helios platform and let the function
'plat_get_power_domain_tree_desc' pick up the correct power
domain tree descriptor based on the platform.

Change-Id: Ibc6d551b570bc740053316a3608c455679d9155b
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

With the two new APIs 'plat_arm_sgi_get_platform_id' and
'plat_arm_sgi_get_config_id' that are available now, BL31 need not
depend on hw_config device tree to identify the platform. In addition
to this, the existing hardware description in hw_config can be limited
to use by BL33 and not by the operating system.

So the hardware description from hw_config dts can be moved into
nt_fw_config dts and the use of hw_config dts can be removed.

Change-Id: I873b7e1e72823d3ec5d253a848e85ae724f09e49
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

Add two new functions 'plat_arm_sgi_get_platform_id' and
'plat_arm_sgi_get_config_id' which will be implemented by all the
SGI platforms. These functions can be used to determine the part
number and configuration id of the SGI platforms.

In BL2, these functions are used to populate the 'system-id' node.
In BL31, these functions are used to populate the 'sgi_plat_info_t'
structure with the part number and configuration id of the platform.

Change-Id: I3bacda933527724a3b4074ad4ed5b53a81ea4689
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

In order to allow Arm platforms to override the default list of PSCI
callbacks, remove the existing weak implementation of
'plat_arm_psci_override_pm_ops' function and let all the Arm platforms
implement their own 'plat_arm_psci_override_pm_ops' function.

For platforms that support SCMI protocol, the function
'css_scmi_override_pm_ops' can be additionally used as well to
override the default PSCI callbacks.

Change-Id: If7c27468bd51a00ea9c2a3716b5894163f5a9f3c
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

For platforms with multi-threaded CPUs, the number of power domains
supported would be more than the value currently defined by
PLAT_MAX_PWR_LVL. So move the PLAT_MAX_PWR_LVL macro to platform
specific code and let the platform define the number of power domain
levels.

Change-Id: I21c0682e62b397860b2999031a0c9c5ce0d28eed
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

To support platforms which are based on multi-threaded CPUs, override
the weak implementation of plat_arm_get_cpu_pe_count function to return
the number of threads supported by the CPU used in the platform.

Change-Id: Ia680773f1277b17e2d3d2414d87943dcece33e89
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

Remove the platform common plat_arm_security_setup function to allow
platform specific implementations of the security setup function
implemented in the board directory of the platform.

For use by secure software, configure region0 of DMC-620 trustzone
controller to protect the upper 16MB of memory of the first DRAM block
from non-secure accesses.

Change-Id: I9a8c19656702c4fa4f6917b3655b692d443bb568
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

Register a priority level, PLAT_SP_PRI, for secure partition with EL3
exception handling framework(ehf) module.

The secure partition manager(SPM) would raise the core's priority to
PLAT_SP_PRI before entering the secure partition, to protect the core
from getting interrupted while in secure partition.

Change-Id: I686897f052a4371e0efa9b929c07d3ad77249e95
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

SGI-Clark platform is the next version in the Arm's SGI platform
series. One of the primary difference between the SGI-575 platform and
the SGI-Clark platform is the MHU version (MHUv2 in case of SGI-Clark).
Add the required base support for SGI-Clark platform.

Change-Id: If396e5279fdf801d586662dad0b55195e81371e4
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

On SGI platforms that include Ares CPUs, the 'CORE_PWRDN_EN' bit of
'CPUPWRCTLR_EL1' register requires an explicit write to clear it to
enable hotplug and idle to function correctly.

The reset value of the CORE_PWRDN_EN bit is zero but it still requires
this explicit clear to zero. This indicates that this could be a model
related issue but for now this issue can be fixed be clearing the
CORE_PWRDN_EN bit in the platform specific reset handler function.

Change-Id: I8b9884ae27a2986d789bfec2e9ae792ef930944e
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>