GitLab

If the GIC loses power during suspend, which the restore code was
written for, exit early in the post restore power sequence. This
prevents an assert from tripping, and the power sequence isn't needed
in this case anyways.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

At present, the GIC drivers enable Group 0 interrupts only if there are
Secure SPIs listed in the interrupt properties/list. This means that,
even if there are Group 0 SGIs/PPIs configured, the group remained
disabled in the absence of a Group 0 SPI.

Modify both GICv2 and GICv3 SGI/PPI configuration to enable Group 0 when
corresponding SGIs/PPIs are present.

Change-Id: Id123e8aaee0c22b476eebe3800340906d83bbc6d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch brings in the following fixes:

  - The per-PE target data initialized during power up needs to be
    flushed so as to be visible to other PEs.

  - Setup per-PE target data for the primary PE as well. At present,
    this was only setup for secondary PEs when they were powered on.

Change-Id: Ibe3a57c14864e37b2326dd7ab321a5c7bf80e8af
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Some SoCs integrate a GIC in version 1 that is currently not supported
by the trusted firmware. This change hijacks GICv2 driver to handle the
GICv1 as GICv1 is compatible enough with GICv2 as far as the platform
does not attempt to play with virtualization support or some GICv2
specific power features.

Note that current trusted firmware does not use these GICv2 features
that are not available in GICv1 Security Extension.

Change-Id: Ic2cb3055f1319a83455571d6d918661da583f179
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

The GIC driver initialization currently allows an array of interrupts to
be configured as secure. Future use cases would require more interrupt
configuration other than just security, such as priority.

This patch introduces a new interrupt property array as part of both
GICv2 and GICv3 driver data. The platform can populate the array with
interrupt numbers and respective properties. The corresponding driver
initialization iterates through the array, and applies interrupt
configuration as required.

This capability, and the current way of supplying array (or arrays, in
case of GICv3) of secure interrupts, are however mutually exclusive.
Henceforth, the platform should supply either:

  - A list of interrupts to be mapped as secure (the current way).
    Platforms that do this will continue working as they were. With this
    patch, this scheme is deprecated.

  - A list of interrupt properties (properties include interrupt group).
    Individual interrupt properties are specified via. descriptors of
    type 'interrupt_prop_desc_t', which can be populated with the macro
    INTR_PROP_DESC().

A run time assert checks that the platform doesn't specify both.

Henceforth the old scheme of providing list of secure interrupts is
deprecated. When built with ERROR_DEPRECATED=1, GIC drivers will require
that the interrupt properties are supplied instead of an array of secure
interrupts.

Add a section to firmware design about configuring secure interrupts.

Fixes ARM-software/tf-issues#262

Change-Id: I8eec29e72eb69dbb6bce77879febf32c95376942
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The helpers perform read-modify-write on GIC*_ICFGR registers, but don't
serialise callers. Any serialisation must be taken care of by the
callers.

Change-Id: I71995f82ff2c7f70d37af0ede30d6ee18682fd3f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I40feec1fe67a960d035061b54dd55610bc34ce1d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I14e33cfc7dfa93257c82d76fae186b17a1b6d266
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

SPIs can be routed to either a specific PE, or to any one of all
available PEs.

API documentation updated.

Change-Id: I28675f634568aaf4ea1aa8aa7ebf25b419a963ed
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I129725059299af6cc612bafa8d74817f779d7c4f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The back end GIC driver converts and assigns the interrupt type to
suitable group.

For GICv2, a build option GICV2_G0_FOR_EL3 is introduced, which
determines to which type Group 0 interrupts maps to.

 - When the build option is set 0 (the default), Group 0 interrupts are
   meant for Secure EL1. This is presently the case.

 - Otherwise, Group 0 interrupts are meant for EL3. This means the SPD
   will have to synchronously hand over the interrupt to Secure EL1.

The query API allows the platform to query whether the platform supports
interrupts of a given type.

API documentation updated.

Change-Id: I60fdb4053ffe0bd006b3b20914914ebd311fc858
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: Ib700eb1b8ca65503aeed0ac4ce0e7b934df67ff9
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: Ice7511f8df5356851001d2f7dc2a46cfe318f9ba
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I6d61785af0d5330930c709de971a904dc7c3516c
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The PE target mask is used to translate linear PE index (returned by
platform core position) to a bit mask used when targeting interrupts to
a PE, viz. when raising SGIs and routing SPIs.

The platform shall:

  - Populate the driver data with a pointer to array that's to contain
    per-PE target masks.

  - Invoke the new driver API 'gicv2_set_pe_target_mask()' during
    per-CPU initialization so that the driver populates the target mask
    for that CPU.

Platforms that don't intend to target interrupts or raise SGIs need not
populate this.

Change-Id: Ic0db54da86915e9dccd82fff51479bc3c1fdc968
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Document the API in separate platform interrupt controller API document.

Change-Id: If18f208e10a8a243f5c59d226fcf48e985941949
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch fixes an assertion check in the GICv3 ITS helper function.

Change-Id: I75f50d7bf6d87c12c6e24a07c9a9889e5facf4a5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds functions to save and restore GICv3 ITS registers during
system suspend. Please note that the power management of GIC ITS is
implementation defined. These functions only implements the
architectural part of the ITS power management and they do not restore
memory structures or register content required to support ITS. Even if
the ITS implementation stores structures in memory, an implementation
defined power down sequence is likely to be required to flush some
internal ITS caches to memory. If such implementation defined sequence
is not followed, the platform must ensure that the ITS is not power
gated during system suspend.

Change-Id: I5f31e5541975aa7dcaab69b0b7f67583c0e27678
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

During system suspend, the GICv3 Distributor and Redistributor context
can be lost due to power gating of the system power domain. This means
that the GICv3 context needs to be saved prior to system suspend and
restored on wakeup. Currently the consensus is that the Firmware should
be in charge of this. See tf-issues#464 for more details.

This patch introduces helper APIs in the GICv3 driver to save and
restore the Distributor and Redistributor contexts. The GICv3 ITS
context is not considered in this patch because the specification says
that the details of ITS power management is implementation-defined.
These APIs are expected to be appropriately invoked by the platform
layer during system suspend.

Fixes ARM-software/tf-issues#464

Change-Id: Iebb9c6770ab8c4d522546f161fa402d2fe02ec00
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Tidy up the code a bit by turning some macros into inline functions
which allows to remove the do/while(0) idiom and backslashes at the end
of the line.

Change-Id: Ie41a4ea4a4da507f7b925247b53e85019101d717
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Reindent the file using tabs as the mix of spaces and tabs confuses some
editors and leads them to use spaces instead of tabs for new code
although the coding style mandates tabs.

Change-Id: I87fa4a5d368a048340054b9b3622325f3f7befba
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

The type `unsigned long` is 32 bit wide in AArch32, but 64 bit wide in
AArch64. This is inconsistent and that's why we avoid using it as per
the Coding Guidelines. This patch changes all `UL` occurrences to `U`
or `ULL` depending on the context so that the size of the constant is
clear.

This problem affected the macro `BIT(nr)`. As long as this macro is used
to fill fields of registers, that's not a problem, since all registers
are 32 bit wide in AArch32 and 64 bit wide in AArch64. However, if the
macro is used to fill the fields of a 64-bit integer, it won't be able
to set the upper 32 bits in AArch32.

By changing the type of this macro to `unsigned long long` the behaviour
is always the same regardless of the architecture, as this type is
64-bit wide in both cases.

Some Tegra platform files have been modified by this patch.

Change-Id: I918264c03e7d691a931f0d1018df25a2796cc221
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The driver has only one API: to initialize an SMMUv3 device. This
operates on a device that implements secure state, by invalidating
secure caches and TLBs.

Change-Id: Ief32800419ddf0f1fe38c8f0da8f5ba75c72c826
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The current build system and driver requires the CCI product to be
specified at build time. The device constraints can be determined at run
time from its ID registers, obviating the need for specifying them
ahead.

This patch adds changes to identify and validate CCI at run time. Some
global variables are renamed to be in line with the rest of the code
base.

The build option ARM_CCI_PRODUCT_ID is now removed, and user guide is
updated.

Change-Id: Ibb765e349d3bc95ff3eb9a64bde1207ab710a93d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

ARM GIC-600 IP complies with ARM GICv3 architecture, but among others,
implements a power control register in the Redistributor frame. This
register must be programmed to mark the frame as powered on, before
accessing other registers in the frame. Rest of initialization sequence
remains the same.

The driver provides APIs for Redistributor power management, and
overrides those in the generic GICv3 driver. The driver data is shared
between generic GICv3 driver and that of GIC-600.

For FVP platform, the GIC-600 driver is chosen when FVP_USE_GIC_DRIVER
is set to FVP_GIC600. Also update user guide.

Change-Id: I321b2360728d69f6d4b0a747b2cfcc3fe5a20d67
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Many asserts depend on code that is conditionally compiled based on the
DEBUG define. This patch modifies the conditional inclusion of such code
so that it is based on the ENABLE_ASSERTIONS build option.

Change-Id: I6406674788aa7e1ad7c23d86ce94482ad3c382bd
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

C files shouldn't be included into others. This file only contains some
macros and functions that can be made `static inline`, so it is ok to
convert it into a header file.

This is the only occurrence of a C file being included in another one in
the codebase instead of using a header, other occurrences are a way of
achieving backwards-compatibility.

Functions therein have been qualified as `inline`.

Change-Id: I88fe300f6d85a7f0740ef14c9cb8fa54849218e6
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The amount of console output is controlled by the LOG_LEVEL build
option. Using tf_printf without any #ifdef depending on the LOG_LEVEL
doesn't give the user that flexibility.

This patch replaces all occurrences of tf_printf that prints error, but
aren't dependent on LOG_LEVEL, with the ERROR macro.

Change-Id: Ib5147f14fc1579398a11f19ddd0e840ff6692831
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This function ensures that console output is flushed, for example
before shutting down or use by another component

In line with other console APIs, console_flush() wraps
console_core_flush().

Also implement console_core_flush() for PL011.

Change-Id: I3db365065e4de04a454a5c2ce21be335a23a01e4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Due to incorrect conditional compilation checks, bakery locks were
excluded from the CCN driver and the power controller driver for FVP
when BL32 was built as the EL3 Runtime Software in AArch32 mode.
This patch corrects the same.

Change-Id: Ib1f163d9167a5c38e4d622232c4835cad9c235aa
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The GIC driver data is initialized by the primary CPU with caches
enabled. When the secondary CPU boots up, it initializes the
GICC/GICR interface with the caches disabled and there is a chance that
the driver data is not yet written back to the memory. This patch fixes
this problem by flushing the driver data after they have been
initialized.

Change-Id: Ie9477029683846209593ff005d2bac559bb8f5e6
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

One nasty part of ATF is some of boolean macros are always defined
as 1 or 0, and the rest of them are only defined under certain
conditions.

For the former group, "#if FOO" or "#if !FOO" must be used because
"#ifdef FOO" is always true.  (Options passed by $(call add_define,)
are the cases.)

For the latter, "#ifdef FOO" or "#ifndef FOO" should be used because
checking the value of an undefined macro is strange.

Here, IMAGE_BL* is handled by make_helpers/build_macro.mk like
follows:

  $(eval IMAGE := IMAGE_BL$(call uppercase,$(3)))

  $(OBJ): $(2)
          @echo "  CC      $$<"
          $$(Q)$$(CC) $$(TF_CFLAGS) $$(CFLAGS) -D$(IMAGE) -c $$< -o $$@

This means, IMAGE_BL* is defined when building the corresponding
image, but *undefined* for the other images.

So, IMAGE_BL* belongs to the latter group where we should use #ifdef
or #ifndef.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

We are duplicating this macro define, and it is useful enough
to be placed in the common place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Some GICv3 implementations have provision for power management
operations at Redistributor level. This patch introduces and provides
place-holders for Redistributor power management. The default
implementations are empty stubs, but are weakly bound so as to enable
implementation-specific drivers to override them.

Change-Id: I4fec1358693d3603ca5dce242a2f7f0e730516d8
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch makes following miscellaneous fixes:
* pl011_console.S: Fixed the bit mask used to check if the
  transmit FIFO is full or empty.
* smcc_macros.S: Added `_fsxc` suffix while updating the SPSR.
  By default the assembler assumes `_fc` suffix which does not
  update all the fields in SPSR. By adding `_fsxc` suffix all
  the fields gets updated.
* platform_helpers.S: Removed the weak definition for
  `plat_my_core_pos()` as this is a mandatory function which
  needs to be defined by all platforms.

Change-Id: I8302292533c943686fff8d7c749a07132c052a3b
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>

Currently the GICv3 driver mandates that platform populate
both G1S and G0 interrupts. However, it is possible that a
given platform is not interested in both the groups and
just needs to specify either one of them.

This patch modifies the `gicv3_rdistif_init()` & `gicv3_distif_init()`
functions to allow either G1S or G0 interrupts to be configured.

Fixes ARM-software/tf-issues#400

Change-Id: I43572b0e08ae30bed5af9334f25d35bf439b0d2b

As per the GICv3 specification, to power down a processor using GICv3
and allow automatic power-on if an interrupt must be sent to a processor,
software must set Enable to zero for all interrupt groups(by writing to
GICC_CTLR or ICC_IGRPEN{0,1}_EL1/3 as appropriate.

Also, NonSecure EL1 software may not be aware of the CPU power state
details and fail to choose right states that require quiescing the CPU
interface. So it's preferred that the PSCI implementation handles it as
it is fully aware of the CPU power states.

This patch adds disabling of Group1 NonSecure interrupts during processor
power down along with Group0 and Group1 Secure interrupts so that all the
interrupt groups are handled at once as per specification.

Change-Id: Ib564d773c9c4c41f2ca9471451c030e3de75e641

This patch adds console drivers including the pl011 driver
for the AArch32 mode.

Change-Id: Ifd22520d370fca3e73dbbf6f2d97d6aee65b67dd

This patch modifies GICv3 and TZC drivers to add AArch32 support.
No modifications are required for the GICv2 driver for AArch32 support.
The TZC driver assumes that the secure world is running in Little-Endian
mode to do 64 bit manipulations. Assertions are present to validate the
assumption.

Note: The legacy GICv3 driver is not supported for AArch32.

Change-Id: Id1bc75a9f5dafb9715c9500ca77b4606eb1e2458