GitLab

- Remove references to removed build options.
- Remove support for legacy GIC driver.
- Remove support for LOAD_IMAGE_V2=0.

Change-Id: I72f8c05620bdf4a682765e6e53e2c04ca749a3d5
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The patch d323af9e

 removed the support for coherent memory in BL1 and
BL2 for ARM platforms. But the CryptoCell SBROM  integration depends
on use of coherent buffers for passing data from the AP CPU to the
CryptoCell. Hence this patch reintroduces support for coherent
memory in BL1 and BL2 if ARM_CRYPTOCELL_INTEG=1.

Change-Id: I011482dda7f7a3ec9e3e79bfb3f4fa03796f7e02
Signed-Off-by: Soby Mathew <soby.mathew@arm.com>

The patch 7b56928a

 unified the FWU mechanism on FVP and Juno
platforms due to issues with MCC firmware not preserving the
NVFLAGS. With MCCv150 firmware, this issue is resolved. Also
writing to the NOR flash while executing from the same flash
in Bypass mode had some stability issues. Hence, since the
MCC firmware issue is resolved, this patch reverts to the
NVFLAGS mechanism to detect FWU. Also, with the introduction
of SDS (Shared Data Structure) by the SCP, the reset syndrome
needs to queried from the appropriate SDS field.

Change-Id: If9c08f1afaaa4fcf197f3186887068103855f554
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
Signed-off-by: Soby Mathew <Soby.Mathew@arm.com>

A cache flush is added in BL1, in Mbed TLS shared heap code. Thus, we
ensure that the heap info written to the DTB always gets written back to
memory.  Hence, sharing this info with other images is guaranteed.

Change-Id: I0faada31fe7a83854cd5e2cf277ba519e3f050d5
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

In Mbed TLS shared heap code, an additional sanity check is introduced
in BL2. Currently, when BL2 shares heap with BL1, it expects the heap
info to be found in the DTB. If for any reason the DTB is missing, BL2
cannot have the heap address and, hence, Mbed TLS cannot proceed. So,
BL2 cannot continue executing and it will eventually crash.  With this
change we ensure that if the DTB is missing BL2 will panic() instead of
having an unpredictable crash.

Change-Id: I3045ae43e54b7fe53f23e7c2d4d00e3477b6a446
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

This patch, firstly, makes the error messages consistent to how printed
strings are usually formatted. Secondly, it removes an unnecessary #if
directive.

Change-Id: Idbb8ef0070562634766b683ac65f8160c9d109e6
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

This patch introduces the shared Mbed TLS heap optimisation for Arm
platforms. The objective is the Mbed TLS heap to be shared between BL1
and BL2 so as to not allocate the heap memory twice. To achieve that,
the patch introduces all the necessary helpers for implementing this
optimisation. It also applies it for FVP.

Change-Id: I6d85eaa1361517b7490956b2ac50f5fa0d0bb008
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

Add another level of abstraction of weak defs for
arm_bl2_handle_post_image_load to prevent two weak definitions
of the same function

Change-Id: Ie953786f43b0f88257c82956ffaa5fe0d19603db
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Change-Id: I5993b425445ee794e6d2a792c244c0af53640655
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Small patch which removes some redundant casts to (void *).

Change-Id: If1cfd68f2989bac1d39dbb3d1c31d4119badbc21
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

These changes address most of the required MISRA rules. In the process,
some from generic code is also fixed.

No functional changes.

Change-Id: I707dbec9b34b802397e99da2f5ae738165d6feba
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Change-Id: I1bb310e1b05968d30b28913c4011c0601e1ae64e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Idb9ba3864d6de3053260724f07172fd32c1523e0
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This omission causes a build error as the definition for
arm_tzc_regions_info_t is needed from plat_arm.h

Change-Id: I26935ee90d3e36ab6a016ff2c4eee4413df3e4e8
Signed-off-by: Nariman Poushin <nariman.poushin@linaro.org>

TF Makefile was linking all the objects files generated for the
fdt library instead of creating a static library that could be
used in the linking stage.

Change-Id: If3705bba188ec39e1fbf2322a7f2a9a941e1b90d
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

TF won't build since no memory region is specified
for when SEPARATE_CODE_AND_RODATA=0 it still relies on
the ARM_MAP_BL_RO_DATA region which is never defined for
this case. Create memory region combining code and RO data for
when the build flag SEPARATE_CODE_AND_RODATA=0 to fix this

Change-Id: I6c129eb0833497710cce55e76b8908ce03e0a638
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

The board_arm_def.h header file needs to be included via the platform
definition header. Not doing so, results in a redefinition error of
PLAT_ARM_MAX_BL31_SIZE macro, if defined in the platform definition
file.

Change-Id: I1d178f6e8a6a41461e7fbcab9f6813a2faa2d82b
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

Change arm_setup_page_tables() to take a variable number of memory
regions. Remove coherent memory region from BL1, BL2 and BL2U as
their coherent memory region doesn't contain anything and
therefore has a size of 0. Add check to ensure this
doesn't change without us knowing.

Change-Id: I790054e3b20b056dda1043a4a67bd7ac2d6a3bc0
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

This also gets rid of MISRA violations for Rule 8.3 and 8.4.

Change-Id: I45bba011b16f90953dd4b260fcd58381f978eedc
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Fix violations of MISRA C-2012 Rules 10.1, 10.3, 13.3, 14.4, 17.7 and
17.8.

Change-Id: I6c9725e428b5752f1d80684ec29cb6c52a5c0c2d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Iaebbeac1a1d6fbd531e5694b95ed068b7a193e62
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

The plat_arm_mmap variable is already declared in plat_arm.h, which is
included from plat/arm/common/arm_common.c.

Similarly, plat_arm.h declares the 'plat_arm_psci_pm_ops' variable, which
does not need to be declared again in plat/arm/common/arm_pm.c.

The duplication was not compliant with MISRA rule 8.5.

Change-Id: Icc42547cc025023226b1078a7ec4f06d093364b7
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Wherever we use 'struct foo' and 'foo_t' interchangeably in a
function's declaration and definition, use 'struct foo' consistently
for both, as per the TF-A coding guidelines [1].

[1] https://github.com/ARM-software/arm-trusted-firmware/wiki/ARM-Trusted-Firmware-Coding-Guidelines#avoid-anonymous-typedefs-of-structsenums-in-header-files



Change-Id: I7998eb24a26746e87e9b6425529926406745b721
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Currenly the CNTFRQ register and system timer is initialized in BL31 for
use by the normal world. During firmware update, the NS-BL1 or NS-BL2U
may need to access the system timer. Hence this patch duplicates the
CNTFRQ and system timer initialization in BL1 as well.
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Change-Id: I1ede78b4ae64080fb418cb93f3e48b26d7b724dc

The file arm_ras.c intended to provide common platform-specific RAS
configuration for Arm platforms. Because this file has symbol
definitions, it's proving difficult to provide a common definition.

This patch therefore renames and makes the file specific to FVP. Other
platforms shall provide their own configuration in similar fashion.

Change-Id: I766fd238946e3e49cdb659680e1b45f41b237901
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Currently TF-A doesn't initialise CNTFRQ register in CNTCTLBase
frame of the system timer. ARM ARM states that "The instance of
the register in the CNTCTLBase frame must be programmed with this
value as part of system initialization."

The psci_arch_setup() updates the CNTFRQ system register but
according to the ARM ARM, this instance of the register is
independent of the memory mapped instance. This is only an issue
for Normal world software which relies on the memory mapped
instance rather than the system register one.

This patch resolves the issue for ARM platforms.

The patch also solves a related issue on Juno, wherein
CNTBaseN.CNTFRQ can be written and does not reflect the value of
the register in CNTCTLBase frame. Hence this patch additionally
updates CNTFRQ register in the Non Secure frame of the CNTBaseN.

Fixes ARM-Software/tf-issues#593

Change-Id: I09cebb6633688b34d5b1bc349fbde4751025b350
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size reserved for BL2 has been increased.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

In Arm platforms, when using dynamic configuration, the necessary
parameters are made available as a DTB. The DTB is loaded by BL1 and,
later on, is parsed by BL1, BL2 or even both, depending on when
information from the DTB is needed.

When the DTB is going to be parsed, it must be validated first, to
ensure that it is properly structured. If an invalid DTB is detected
then:
  - BL1 prints a diagnostic but allows execution to continue,
  - BL2 prints a diagnostic and panics.

Now the behaviour of BL1 is changed so for it also to panic. Thus, the
behaviour of BL1 and BL2 is now similar.

Keep in mind that if BL1 only loads the DTB but it doesn't need to
read/write it, then it doesn't validate it. The validation is done only
when the DTB is actually going to be accessed.

Change-Id: Idcae6092e6dbeab7248dd5e041d6cbb7784fe410
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

RFC4122 defines that fields are stored in network order (big endian),
but TF-A stores them in machine order (little endian by default in TF-A).
We cannot change the future UUIDs that are already generated, but we can store
all the bytes using arrays and modify fiptool to generate the UUIDs with
the correct byte order.

Change-Id: I97be2d3168d91f4dee7ccfafc533ea55ff33e46f
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

The translation tables allocated for the Secure Partition do not need
to be treated as a special case. They can be put amongst the other
tables mapping BL31's general purpose memory. They will be mapped with
the same attributes as them, which is fine.

The explicit alignment constraint in BL31's linker script to pad the
last page of memory allocated to the Secure Partition's translation
tables is useless too, as page tables are per se pages, thus their
end address is naturally aligned on a page-boundary.

In fact, this patch does not change the existing behaviour. Since
patch 22282bb6

 ("SPM: Move all SP-related info to SP context
struct"), the secure_partition.c file has been renamed into sp_xlat.c
but the linker script has not been properly updated. As a result, the
SP translation tables are not specifically put at the start of the
xlat_table linker section, the __SP_IMAGE_XLAT_TABLES_START__/_END__
symbols have the same value, the size of the resulting mmap_region
covering these xlat tables is 0 and so it is ignored.

Change-Id: I4cf0a4cc090298811cca53fc9cee74df0f2b1512
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

The patch changes the layout of BL images in memory to enable
more efficient use of available space. Previously BL31 was loaded
with the expectation that BL2 memory would be reclaimed by BL32
loaded in SRAM. But with increasing memory requirements in the
firmware, we can no longer fit BL32 in SRAM anymore which means the
BL2 memory is not reclaimed by any runtime image. Positioning BL2
below BL1-RW and above BL31 means that the BL31 NOBITS can be
overlaid on BL2 and BL1-RW.

This patch also propogates the same memory layout to BL32 for AArch32
mode. The reset addresses for the following configurations are also
changed :
   * When RESET_TO_SP_MIN=1 for BL32 in AArch32 mode
   * When BL2_AT_EL3=1 for BL2

The restriction on BL31 to be only in DRAM when SPM is enabled
is now removed with this change. The update to the firmware design
guide for the BL memory layout is done in the following patch.

Change-Id: Icca438e257abe3e4f5a8215f945b9c3f9fbf29c9
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The weak pragma was assigned twice to the bl2_plat_handle_post_image_load
definition both in plat/common/ and in plat/arm/common/ this was an error as
it should have only have been defined in plat/common

Change-Id: Id85e14c699cb09ed998d1677f2a172e760911918
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.

The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.

Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.

The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.

Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This reverts commit 2f18aa1f

.

It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.

Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Normally, BL33 needs to contain a boot loader like U-Boot or UEFI that
eventually gives control to the OS. However, in some cases, this boot
sequence may be too slow. For example, when doing tests in a
cycle-accurate emulator, the user may only be interested in the
interaction between the Trusted Firmware and the OS, not in the boot
process itself.

The new option ARM_LINUX_KERNEL_AS_BL33 allows BL33 to contain the Linux
kernel image by changing the value of registers x0-x3 to the values
expected by the kernel. This option requires the device tree blob (DTB)
to be present in memory. Its address must be specified in the newly
introduced ARM_PRELOADED_DTB_BASE build option. For now, it only supports
AArch64 kernels.

This option is only available when RESET_TO_BL31=1. For this reason
the BL33 binary must be preloaded in memory and PRELOADED_BL33_BASE must
be used.

For example, if the kernel is loaded at 0x80080000 and the DTB is loaded
at address 0x82000000, the firmware could be built like this:

    CROSS_COMPILE=aarch64-linux-gnu-  \
    make PLAT=fvp DEBUG=1             \
    RESET_TO_BL31=1                   \
    ARM_LINUX_KERNEL_AS_BL33=1        \
    PRELOADED_BL33_BASE=0x80080000    \
    ARM_PRELOADED_DTB_BASE=0x82000000 \
    all fip

Change-Id: If9dc847c65ae2d0c27b51f0fd44fc06b28497db9
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size of BL31 has been increased in builds with SPM.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

  - Assign 0x10 for RAS exceptions on ARM platforms, and install
    EHF priority descriptor.

  - Call the common RAS initialisation from ARM BL31 setup.

  - Add empty definitions for platform error records and RAS interrupts.

Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.

The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.

Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>