GitLab

To catch early hangs in resume, this sets up the watchdog before
anything else in the pmusram code (ignoring setting up the stack...).
This uses hard coded settings for the watchdog until the proper
watchdog restore later on in the firmware/kernel.

This also restores the old watchdog register values before the PLLs
are restored to make sure we don't temporarily switch over to a 1/3s
timeout on the watchdog when the pclk_wdt goes from 4MHz to 100MHz.

Change-Id: I8f7652089a88783271b17482117b4609330abe80
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

All the m0 code run in SRAM before, but we need to watch PMU_POWER_ST
when SOC enter into FSM, and SRAM will shutdown during this time, so
this code need run in PMUSRAM. But PMUSRAM only 8K space, we can not
put all the m0 binary into PMUSRAM, Split the M0 binary into two, dram
part still run in SRAM, and suspend part run in PMUSRAM.

Change-Id: Ie08bdf3e2b8838f12b9297fe60ab0aad219684b1
Signed-off-by: Lin Huang <hl@rock-chips.com>

we need to enable PMU_WKUP_RST_EN for pmu powermode configure, since
enable wakeup reset will hold the soc status, so the SOC will not affect
by some power or other single glitch when resume, and keep the soc in the
right status. And it not need to enable DDRIO_RET_HW_DE_REQ, the ddr resume
will do it manual.

Change-Id: Ib4af897ffb3cb63dc2aa9a6002e5d9ef86ee4a49
Signed-off-by: Lin Huang <hl@rock-chips.com>

This fixes an off by 576x bug the the sram_udelay code. The wrong
value was multipled by the system ticks per mhz value (which is 24),
so we delayed for 1/576th of the requested time.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

Ensure (where possible) that switch statements in plat comply with MISRA
rules 16.1 - 16.7.

Change-Id: Ie4a7d2fd10f6141c0cfb89317ea28a755391622f
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>

When the source code says 'SMCC' it is talking about the SMC Calling
Convention. The correct acronym is SMCCC. This affects a few definitions
and file names.

Some files have been renamed (smcc.h, smcc_helpers.h and smcc_macros.S)
but the old files have been kept for compatibility, they include the
new ones with an ERROR_DEPRECATED guard.

Change-Id: I78f94052a502436fdd97ca32c0fe86bd58173f2f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

there are two fix for save/restore watchdog register:
1. watchdog plck will shutdown after secure_watchdog_disable(), so need
   to save register before it and restore after secure_watchdog_enable().
2. need write 0x76 to cnt_restart to keep watchdog alive when restore
   watchdog register.

Change-Id: I1f6fbceae22186e3b72a87df6332a110adf37479
Signed-off-by: Lin Huang <hl@rock-chips.com>

Coverity scan done for the coreboot project found the issue:
Coverity (*** CID 1385418: Memory - illegal accesses (OVERRUN))
Coverity (*** CID 1385419: Memory - corruptions  (OVERRUN))

Fix the Converity error issue with store_cru[] loop needs to be one
element bigger.

Fixes: ARM-software/tf-issues#544

Change-Id: I420f0a660b24baaa5fc5e78fca242cf750c9bbc7
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This adds calls to the GICv3 save/restore functions for the GIC
distributor and redistributor.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

We were looping for MAX_WAIT_COUNT in several places without any
delays, so this adds the delays to make those loops more predictable.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The code was accidentally restoring the QOS on suspend and saving the
QOS on resume. This is the opposite of what we want.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This brings ATF into line with the kernel on the timeout for power
domains turning on. We could actually timeout (when we shouldn't) on
resume when turning power domains on. The guaranteed maximum delay is
now 10ms.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

when shutdown logic power rail, the some sgrf register
value will reset, so need to reinitilize secure.

Change-Id: I8ad0570432e54441fe1c60dd2960a81fd58f7163
Signed-off-by: Lin Huang <hl@rock-chips.com>

we will use timer in pmusarm, when logic power rail shutdown,
the secure timer will gone, so need to initial it in pmusram.

Change-Id: I472e7eec3fc197f56223e6fff9167556c1c5e3bc
Signed-off-by: Lin Huang <hl@rock-chips.com>

we do not have enough pmusram space now, so use slice1 to restore
ddr slice1 ~ slice4, that's will save more pmusram space.

Change-Id: Id54a7944f33d01a8f244cee6a8a0707bfe4d42da
Signed-off-by: Lin Huang <hl@rock-chips.com>

Change-Id: Ia59adf48cf14eb627721264765bce50cb31065ef
Signed-off-by: Lin Huang <hl@rock-chips.com>

pd_alive control cru, grf, timer, gpio and wdt, when
turn off logic power rail, these register value will
back to reset value, we need to save them value in suspend
and restore them when resuem, since timer will reinitial
in kernel, so it not need to save/restore.

Change-Id: I0fc2a011d3cdc04b66ffbf728e769eb28b51ee38
Signed-off-by: Lin Huang <hl@rock-chips.com>

when logic power rail shutdown, CRU register will back to reset
value, ddr use abpll as clock source when do suspend, we need to save
and dpll value in pmusram, then set back these ddr clock back to dpll
when dddr resume.

Change-Id: I95dc0173649e8515859cfa46b40a606e0cc2fe3f
Signed-off-by: Lin Huang <hl@rock-chips.com>

when shutdown logic power rail, the uart register value will reset,
so need to reinitilize debug uart.

Change-Id: I48d3535c0068fd671dea6ea32e908612992faf62
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This fix modifies the order of system includes to meet the ARM TF coding
standard. There are some exceptions to this change in order to retain
header groupings and where there are headers within #if statements.

Change-Id: Ib5b668c992d817cc860e97b29e16ef106d17e404
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>

Decrypt device private keys which transfer from kernel, then stuff it to
DP controller. So that DP driver could start HDCP authentication in
kernel.

Change-Id: If3c2cd99bca811fe5fc30acc88bf5dc1afd7416d
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This patch fixes the two things as follows:

1) rk3399_flash_l2_b" seems to be a typo. That's "flush", not "flash".

2) fixes the warnings log.
We always hit the warnings thing during the suspend, as below log:
..
[   51.022334] CPU5: shutdown
[   51.025069] psci: CPU5 killed.
INFO:    sdram_params->ddr_freq = 928000000
WARNING: rk3399_flash_l2_b:reg 28830380,wait

When the L2 completes the clean and invalidate sequence, it asserts the
L2FLUSHDONE signal. The SoC can now deassert L2FLUSHREQ signal and then
the L2 deasserts L2FLUSHDONE.

Then, a loop without a delay isn't really great to measure time. We should
probably add a udelay(10) or so in there and then maybe replace the WARN()
after the loop. In the actual tests, the L2 cache will take ~4ms by
default for big cluster.

In the real world that give 10ms for the enough margin, like the
ddr/cpu/cci frequency and other factors that will affect it.

Change-Id: I55788c897be232bf72e8c7b0e10cf9b06f7aa50d
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

For some reason, HDCP key decrytion can't open source in ATF, so we
build it as hdcp.bin. Besides declare the handler for decrypting.

Change-Id: Ia67ff2442ab43cb3ee4875b3d59cc1608e854b4b
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

with PMU_PERILP_PD_EN bit enable, the soc will shutdown
cm0, crypto, dcf, imem(normal SRAM), dmac, bootrom, efuse_con,
spi, i2c, uart, saradc, tsadc when suspend, we have M0 code
need to run when suspend in normal SRAM, so we need to take
care of that.

Change-Id: I8c066637e5b81d4b1d53197450b9d592cbe00793
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This moves the DRAM restore code to PMUSRAM. This is so that the
voltage domain that contains the SRAM that it was stored in before may
be turned off during system suspend.

Change-Id: Id761181a30caadd12f1ce061d1034f3159a76d28
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This converts two functions to use for-loops. This saves a bit of
space to help moving DRAM resume code to PMUSRAM.

Change-Id: Ie6ca490cf50c2ec83335cf1845b337c3e8a47496
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The removed if statement would make the same check that the for loop
it is in does to break out of the for loop, so it doesn't make any
sense to keep it there.

Change-Id: I819c29f9182e6de1fc47e418aed15ad38e8f9fa9
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes the mmio_... function calls to set the multicast bit for
the PHY registers when overriding the write leveling values. These are
not needed since multicast is set by default when calling the
function, and it's also better not to leave the side effect of
disabling multicast when exiting the function.

Change-Id: I83e089a2a2d55268b3832f36724c3b2c4be81082
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes the phy_dll_bypass_set function as it is unneeded. The
values that function sets are saved during suspend, so the proper
values will be restored on resume.

Change-Id: I17542206c56e639ce8cb6375233145167441d4e2
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes the space allocation for the unused PHY register space.
For instance in PHY registers 0-127, only 0-90 are used, so don't save
the 91-127 registers. This saves about 1.6KB of space.

Change-Id: I0c9f6d9bed8f0c1f3b8b805dfb10cf0c06208919
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

the function pmu_cpuon_entrypoint() need to run in the pmusram,
we just copy bin file to pmusram before, now we add pmusram section
and link pmu_cpuon_entrypoint() to pmusram directly

Change-Id: Iae31e4c01c480c8e6f565a8f588332b478efdb16
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

The differential signal of DQS need keep low level
before gate training. It need enable RPULL and disable
PHY side ODT to ensure it when do gate training.
But it can not access the PHY registers to do it when
perform DFS.So the workaroud as below: It is ensure that
the PHY's read gate is landing somewhere in the incoming
DQS's pulses before it starts searching for pre-amble window.
It need get the rddqs_delay_ps to calculate the start point
of gate training for DFS.

Change-Id: I79eabcf4ec9a9c8f4539f68a51f22afba49c72fe
Signed-off-by: Lin Huang <hl@rock-chips.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

The printf() isn't used by the firmware itself, just by the tools under
the ./tools/ folder. Then tf_printf will unconditionally print.
Remove the unused print_dram_status_info() function.

Change-Id: Ie699ccb54a5be9a2cbbd7b8d4193b57075a2f57a
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

Remove struct rockchip_pm_ops_cb and instead of using weak functions
implement; in this way we want the codes look clear and simple;

Change-Id: Ib9e8a5e932fdfc2b3e6a1ec502c40dfe720ac400
Signed-off-by: tony.xie <tony.xie@rock-chips.com>

Sorry to miss the security configuration for SRAM, if we don't support
it, somebody may modify the comment of SRAM in the non-secure space.
Let's fix this issue.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This fixes code that set a tFC value in a register using the tRFC
value instead.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The F1 CAS latency setting was not bit shifted, which resulted in
setting the DRAM additive latency value instead.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

On resume, we use the DFS hardware to switch frequency index,
followed by a full training sequence on that index. Leaving
the DFS training modules enabled causes issues with the full
training done at resume. We also only needs these enabled
during a call to ddr_set_rate during runtime, so there's no
issue disabling them at the end of ddr_set_rate.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This moves the setting of the DQS drive strength to the M0 to minimize
the impact on DDR transactions. We need to have the DQS drive strength
changed for data training, which is triggered by the M0, but it also
needs to be changed back when data training is finished.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>