GitLab

This feature is only supported on FVP.

Change-Id: I4e265610211d92a84bd2773c34acfbe02a1a1826
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Replace all usage of 'sgiclark' with 'rdn1e1edge' and 'sgiclarkh' with
'rde1edge' as per the updated product names.

Change-Id: I14e9b0332851798531de21d70eb54f1e5557a7bd
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

Replace all usage of 'sgiclark' with 'rdn1e1edge' and 'sgiclarka' with
'rdn1edge' as per the updated product names.

Change-Id: Idbc157c73477ec32f507ba2d4a4e907d8813374c
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

This commit improves the SDHost driver for RPi3 as following:
 * Unblock MMC_CMD(17). Using MMC_CMD(17) is more efficient on
   block reading.
 * In some low probability that SEND_OP_COND might results CRC7
   error. We can consider that the command runs correctly. We don't
   need to retry this command so removing the code for retry.
 * Using MMC_BUS_WIDTH_1 as MMC default value to improve the stability.
 * Increase the clock to 50Mhz in data mode to speed up the io.
 * Change the pull resistors configuration to gain more stability.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

This adds BL31 support to Intel Stratix10 SoCFPGA platform. BL31 in TF-A
supports:
- PSCI calls to enable 4 CPU cores
- PSCI mailbox calls for FPGA reconfiguration
Signed-off-by: Loh Tien Hock <tien.hock.loh@intel.com>

STM32MP1 chip embeds a dual Cortex-A7 and a Cortex-M4.
The support for Cortex-M4 clocks is added when configuring the clock tree.
Some minimal security features to allow communications between A7 and M4
are also added.

Change-Id: I60417e244a476f60a2758f4969700b2684056665
Signed-off-by: Yann Gautier <yann.gautier@st.com>

In case the PCIe controller receives a L1_Enter_PM DLLP, it will
disable the internal PLLs. The system software cannot predict it
and can attempt to perform device config space access across the
PCIe link while the controller is in this transitional state. If
such condition happens, the PCIe controller register access will
trigger ARM64 SError exception.

This patch adds checks for which PCIe controller is enabled,
checks whether the PCIe controller is in such a transitional
state and if so, first completes the transition and then restarts
the instruction which caused the SError.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Cortex A5 doesnt support VFP, Large Page addressing and generic timer
which are addressed in this patch. The device tree for Cortex a5
is also included.

Change-Id: I0722345721b145dfcc80bebd36a1afbdc44bb678
Signed-off-by: Usama Arif <usama.arif@arm.com>

This patch adds support for Versatile express FVP (Fast models).
Versatile express is a family of platforms that are based on ARM v7.
Currently this port has only been tested on Cortex A7, although it
should work with other ARM V7 cores that support LPAE, generic timers,
VFP and hardware divide. Future patches will support other
cores like Cortex A5 that dont support features like LPAE
and hardware divide. This platform is tested on and only expected to
work on single core models.

Change-Id: I10893af65b8bb64da7b3bd851cab8231718e61dd
Signed-off-by: Usama Arif <usama.arif@arm.com>

Change-Id: I1adcf195c0ba739002f3a59e805c782dd292ccba
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

Change-Id: Ideb49011da35f39ff1959be6f5015fa212ca2b6b
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

The variable is renamed to PLAT_ARM_RUN_UART as
the UART is used outside BL31 as well.

Change-Id: I00e3639dfb2001758b7d24548c11236c6335f64a
Signed-off-by: Usama Arif <usama.arif@arm.com>

Convert them to take an mpidr instead of a (cluster, core) pair. This
simplifies all of the call sites, and actually makes the functions a bit
smaller.
Signed-off-by: Samuel Holland <samuel@sholland.org>

This maximizes the amount of data protected by the MMU.
Signed-off-by: Samuel Holland <samuel@sholland.org>

Remove useless private structure in function prototypes.
Add a reference counter on clocks.
Prepare for future secured/shared/non-secured clocks.

Change-Id: I3dbed81721da5ceff5e10b2c4155b1e340c036ee
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

PWR, RCC, DDRPHYC & DDRCTRL addresses can be retrieved from device tree.
Platform asserts the value read from the DT are the SoC addresses.

Change-Id: I43f0890b51918a30c87ac067d3780ab27a0f59de
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

Create a new file stm32mp_clkfunc.c to put functions that could be common
between several platforms.

Change-Id: Ica915c796b162b2345056b33328acc05035a242c
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Regulator configuration at boot takes more information from DT.
I2C configuration from DT is done in I2C driver.
I2C driver manages more transfer modes.
The min voltage of buck1 should also be increased to 1.2V,
else the platform does not boot.

Heavily modifies stm32_i2c.c since many functions move inside the source
file to remove redundant declarations.

Change-Id: I0bee5d776cf3ff15e687427cd6abc06ab237d025
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

timeout_init_us(some_timeout_us); returns a reference to detect
timeout for the provided microsecond delay value from current time.

timeout_elapsed(reference) return true/false whether the reference
timeout is elapsed.

This change is inspired by the OP-TEE OS timeout resources [1].

 [1] https://github.com/OP-TEE/optee_os/blob/3.4.0/core/arch/arm/include/kernel/delay.h#L45



Change-Id: Id81ff48aa49693f555dc621064878417101d5587
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Include all RCC, clocks and reset headers from stm32mp1_def.h
which if exported to the firmware through platform_def.h.
The same dependency removal is done in common code as well.
Some useless includes are also removed in stm32_sdmmc2 driver.

Change-Id: I731ea5775c3fdb7f7b0c388b93923ed5e84b8d3f
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Mainly remove suffix 1 from prefix stm32mp1 in several macros and functions
that can be used in drivers shared by different platforms.

Change-Id: I2295c44f5b1edac7e80a93c0e8dfd671b36e88e7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

Some parts of code could be shared with platform derivatives,
or new platforms.
A new folder plat/st/common is created to put common parts.

stm32mp_common.h is a common API aggregate.

Remove some casts where applicable.
Fix some types where applicable.
Remove also some platform includes that are already in stm32mp1_def.h.

Change-Id: I46d763c8d9e15732d1ee7383207fd58206d7f583
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

A DDR calibration value is missing write mask, causing ECC DDR calibration
to fail. This patch addresses the issue. ECC should also be scrubbed before
MMU initializes, thus the scrubbing is moved to ddr intialization phase.
Signed-off-by: Loh Tien Hock <tien.hock.loh@intel.com>

Rather than letting the Trusty makefile set the option to enable dynamic
translation tables, make platforms do it themselves.

This also allows platforms to replace the implementation of the
translation tables library as long as they use the same function
prototypes.

Change-Id: Ia60904f61709ac323addcb57f7a83391d9e21cd0
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This commit migrates to MULTI_CONSOLE_API for IMX Warp7 board.
We also rename the functions in imx_uart driver to more specific one.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

ATF should be the only host needing to control a processor that it has
started. ATF will need this control to stop the core later. Do not
relinquish control of a core after starting the core.
Signed-off-by: Andrew F. Davis <afd@ti.com>

Now that we have non-blocking TI-SCI functions we can initiate the shutdown
sequence from the PSCI handler without needing the ti_sci_proc_shutdown
helper function, which is removed. This gives us the greater control and
flexibility that will be needed when cluster power down sequences are added.
Signed-off-by: Andrew F. Davis <afd@ti.com>

Most TI-SCI functions request an ACK and wait until it is received. For
some power sequence tasks we cannot wait but instead queue messages
asynchronously. Three messages have been identified that will need to
be used in this way. Add non-waiting versions of these functions.
Signed-off-by: Andrew F. Davis <afd@ti.com>

Currently almost all TI-SCI messages request and check for an ACK from
the system firmware. Move this into a common place to remove the same
from each function.
Signed-off-by: Andrew F. Davis <afd@ti.com>

When a device is requested with TI-SCI its control can be made exclusive
to the requesting host. This was currently the default but is not what
is needed most of the time. Add _exclusive versions of the request
functions and remove the exclusive flag from the default version.
Signed-off-by: Andrew F. Davis <afd@ti.com>

The raw get and set state functions for both devices and clocks
are only meant for use internal to the TI-SCI driver, the same
functionality is available from the other API that call into
these. Remove them from the external interface and make them
static scope to the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>

There exists a third DMA controller on the hi3660
SoC called the IOMCU DMAC. This controller is used by
peripherals like SPI2 and UART3. Initialize channels 4-7
as non-secure, while 0-3 remain reserved and secure.
Signed-off-by: Ryan Grachek <ryan@edited.us>

This patch introduces explicit linker variables to mark the start and
end of the per-cpu bakery lock section to help bakery_lock_normal.c
calculate the size of the section. This patch removes the previously
used '__PERCPU_BAKERY_LOCK_SIZE__' linker variable to make the code
uniform across GNU linker and ARM linker.

Change-Id: Ie0c51702cbc0fe8a2076005344a1fcebb48e7cca
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch includes bl_common.h from plat_trampoline.S to link with
the __BL31_END__ symbol.

Change-Id: Ie66c5009018472607db668583c9a0b3553f0ae73
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch modfies the 'tegra_soc_pwr_domain_power_down_wfi' handler
to use BL31_BASE variable, provided by bl_common.h

Change-Id: I9747228d0193c1ae6999284458b9f866955a61a2
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes the unused functions that are marked as .global
in code but not defined anywhere in the code.

Change-Id: Ia5057a77c0b0b4a61043eab868734cd3437304cc
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch stops including common_def.h from platform_def.h to
fix a circular depoendency between them.

This means platform_def.h now has to define the linker macros:
* PLATFORM_LINKER_FORMAT
* PLATFORM_LINKER_ARCH

Change-Id: Icd540b1bd32fb37e0e455e9146c8b7f4b314e012
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The scatterfile to support armlink, does not seem to support
shift operator. To handle this define CACHE_WRITEBACK_GRANULE with
the direct value.

Change-Id: I19afc7cb9c55a08cb0703f284d91018d3214353f
Signed-off-by: Kalyani Chidambaram <kalyanic@nvidia.com>

This patch removes this macro and its usage as it is used only
within the Tegra186 files and all derived platforms keep the
macro enabled.

Change-Id: Ib831b3c002ba4dedc3d5fafbb7d321daa28fa9ea
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch dynamically maps the first page of trusty's code memory,
before accessing it to find out if we are running a 32-bit or 64-bit
image.

On Tegra platforms, this means we have to increase the mappings to
accomodate the new memmap entry.

Change-Id: If370d1e6cfcccd69b260134c1b462d8d17bee03d
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>