GitLab

Some SoCs integrate a GIC in version 1 that is currently not supported
by the trusted firmware. This change hijacks GICv2 driver to handle the
GICv1 as GICv1 is compatible enough with GICv2 as far as the platform
does not attempt to play with virtualization support or some GICv2
specific power features.

Note that current trusted firmware does not use these GICv2 features
that are not available in GICv1 Security Extension.

Change-Id: Ic2cb3055f1319a83455571d6d918661da583f179
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

ARMv7-A Virtualization extensions brings new instructions and resources
that were supported by later architectures. Reference ARM ARM Issue C.c
[DDI0406C_C].

ERET and extended MSR/MRS instructions, as specified in [DDI0406C_C] in
ID_PFR1 description of bits[15:12] (Virtualization Extensions):
 A value of 0b0001 implies implementation of the HVC, ERET, MRS
 (Banked register), and MSR (Banked register) instructions. The ID_ISARs
 do not identify whether these instructions are implemented.

UDIV/SDIV were introduced with the Virtualization extensions, even if
not strictly related to the virtualization extensions.

If ARMv7 based platform does not set ARM_CORTEX_Ax=yes, platform
shall define ARMV7_SUPPORTS_VIRTUALIZATION to enable virtualization
extension related resources.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

As Cortex-A9 needs to manually enable program flow prediction,
do not reset SCTLR[Z] at entry. Platform should enable it only
once MMU is enabled.

Change-Id: I34e1ee2da73221903f7767f23bc6fc10ad01e3de
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Also need to add a SEV instruction in ARMv7 spin_unlock which
is implicit in ARMv8.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

These macros are only defined for corresponding image,
and they are undefined for other images. It means that we have
to use ifdef or defined() instead of relying on being 0 by default.

Change-Id: Iad11efab9830ddf471599b46286e1c56581ef5a7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Change sizeof call so it references a static type instead of return of
a function in order to be MISRA compliant.

Change-Id: I6f1adb206073d6cd200156e281b8d76249e3af0e
Signed-off-by: Joel Hutton <joel.hutton@arm.com>

Add events that trigger before entry to normal/secure world.  The
events trigger after the normal/secure context has been restored.

Similarly add events that trigger after leaving normal/secure world.
The events trigger after the normal/secure context has been saved.

Change-Id: I1b48a7ea005d56b1f25e2b5313d77e67d2f02bc5
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

For Trusted Board Boot, BL2 needs more space to support the ECDSA
and ECDSA+RSA algorithms.

Change-Id: Ie7eda9a1315ce836dbc6d18d6588f8d17891a92d
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>

These hooks are intended to allow one platform to try load
images from alternative places. There is a hook to initialize
the sequence of boot locations and a hook to pass to the next
sequence.

Change-Id: Ia0f84c415208dc4fa4f9d060d58476db23efa5b2
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This allows other EL3 components to subscribe to CPU on events.

Update Firmware Design guide to list psci_cpu_on_finish as an available
event.

Change-Id: Ida774afe0f9cdce4021933fcc33a9527ba7aaae2
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This light-weight framework enables some EL3 components to publish
events which other EL3 components can subscribe to. Publisher can
optionally pass opaque data for subscribers. The order in which
subscribers are called is not defined.

Firmware design updated.

Change-Id: I24a3a70b2b1dedcb1f73cf48313818aebf75ebb6
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The implementation is the same as those used to disable it in EL3.

Change-Id: Ibfe7e69034a691fbf57477c5a76a8cdca28f6b26
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduces a new API in the translation tables library
(v2), that allows to change the memory attributes of a memory
region. It may be used to change its execution permissions and
data access permissions.

As a prerequisite, the memory must be already mapped. Moreover, it
must be mapped at the finest granularity (currently 4 KB).

Change-Id: I242a8c6f0f3ef2b0a81a61e28706540462faca3c
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduces a new API in the translation tables library
(v2), that allows to query the memory attributes of a memory block
or a memory page.

Change-Id: I45a8b39a53da39e7617cbac4bff5658dc1b20a11
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Previously, in AArch32, `IMAGE_XLAT_DEFAULT_REGIME` wasn't defined. The
translation regime is only used in the AArch64 port of the translation
tables library v2, so this is not a problem for now, but future patches
will use it.

`IMAGE_EL` isn't used in AArch32, so it isn't needed to define it.

Change-Id: I4acdb01a58658956ab94bd82ed5b7fee1aa6ba90
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The GIC driver initialization currently allows an array of interrupts to
be configured as secure. Future use cases would require more interrupt
configuration other than just security, such as priority.

This patch introduces a new interrupt property array as part of both
GICv2 and GICv3 driver data. The platform can populate the array with
interrupt numbers and respective properties. The corresponding driver
initialization iterates through the array, and applies interrupt
configuration as required.

This capability, and the current way of supplying array (or arrays, in
case of GICv3) of secure interrupts, are however mutually exclusive.
Henceforth, the platform should supply either:

  - A list of interrupts to be mapped as secure (the current way).
    Platforms that do this will continue working as they were. With this
    patch, this scheme is deprecated.

  - A list of interrupt properties (properties include interrupt group).
    Individual interrupt properties are specified via. descriptors of
    type 'interrupt_prop_desc_t', which can be populated with the macro
    INTR_PROP_DESC().

A run time assert checks that the platform doesn't specify both.

Henceforth the old scheme of providing list of secure interrupts is
deprecated. When built with ERROR_DEPRECATED=1, GIC drivers will require
that the interrupt properties are supplied instead of an array of secure
interrupts.

Add a section to firmware design about configuring secure interrupts.

Fixes ARM-software/tf-issues#262

Change-Id: I8eec29e72eb69dbb6bce77879febf32c95376942
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The helpers perform read-modify-write on GIC*_ICFGR registers, but don't
serialise callers. Any serialisation must be taken care of by the
callers.

Change-Id: I71995f82ff2c7f70d37af0ede30d6ee18682fd3f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.

This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms.  The
deprecated interrupt list definitions are however retained to support
legacy builds.

Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.

NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.

Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I40feec1fe67a960d035061b54dd55610bc34ce1d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I14e33cfc7dfa93257c82d76fae186b17a1b6d266
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

SPIs can be routed to either a specific PE, or to any one of all
available PEs.

API documentation updated.

Change-Id: I28675f634568aaf4ea1aa8aa7ebf25b419a963ed
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I129725059299af6cc612bafa8d74817f779d7c4f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The back end GIC driver converts and assigns the interrupt type to
suitable group.

For GICv2, a build option GICV2_G0_FOR_EL3 is introduced, which
determines to which type Group 0 interrupts maps to.

 - When the build option is set 0 (the default), Group 0 interrupts are
   meant for Secure EL1. This is presently the case.

 - Otherwise, Group 0 interrupts are meant for EL3. This means the SPD
   will have to synchronously hand over the interrupt to Secure EL1.

The query API allows the platform to query whether the platform supports
interrupts of a given type.

API documentation updated.

Change-Id: I60fdb4053ffe0bd006b3b20914914ebd311fc858
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: Ib700eb1b8ca65503aeed0ac4ce0e7b934df67ff9
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: Ice7511f8df5356851001d2f7dc2a46cfe318f9ba
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I6d61785af0d5330930c709de971a904dc7c3516c
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

These APIs allow the GIC implementation to categorize interrupt numbers
into SPIs, PPIs, and SGIs. The default implementations for GICv2 and
GICv3 follows interrupt numbering as specified by the ARM GIC
architecture.

API documentation updated.

Change-Id: Ia6aa379dc955994333232e6138f259535d4fa087
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The PE target mask is used to translate linear PE index (returned by
platform core position) to a bit mask used when targeting interrupts to
a PE, viz. when raising SGIs and routing SPIs.

The platform shall:

  - Populate the driver data with a pointer to array that's to contain
    per-PE target masks.

  - Invoke the new driver API 'gicv2_set_pe_target_mask()' during
    per-CPU initialization so that the driver populates the target mask
    for that CPU.

Platforms that don't intend to target interrupts or raise SGIs need not
populate this.

Change-Id: Ic0db54da86915e9dccd82fff51479bc3c1fdc968
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Document the API in separate platform interrupt controller API document.

Change-Id: If18f208e10a8a243f5c59d226fcf48e985941949
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The macro DEFINE_SYSREG_WRITE_CONST_FUNC defines an inline function
to an assembly statement that uses the MSR (immediate) instruction
to access the PSTATE.  The "i" (immediate) assembly constraint on
the operand was only satisfied when compiling with optimizations
enabled which resulted in the function being optimized out - the
"const uint64_t v" parameter was optimized out and replaced by a
literal value.

When compiling without optimizations, the function call remained and
therefore the parameter is not optimized out - compilation fails as
the constraint is impossible to satisfy by the compiler.

This patch replaces the function encapsulating the use of
the MSR (immediate) with a macro that allows the literal value to be
directly fed to the inline assembly statement

Change-Id: Ib379a7acc48ef3cb83090a680cd8a6ce1a94a9d9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Updated the PSCI version conforming to the PSCI v1.1
specification (ARM DEN022D).

Change-Id: I1f34772ef6de37ec1ade719a1ab3aa062152d995
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Currently TF does not initialise the PMCR_EL0 register in
the secure context or save/restore the register.

In particular, the DP field may not be set to one to prohibit
cycle counting in the secure state, even though event counting
generally is prohibited via the default setting of MDCR_EL3.SMPE
to 0.

This patch initialises PMCR_EL0.DP to one in the secure state
to prohibit cycle counting and also initialises other fields
that have an architectually UNKNOWN reset value.

Additionally, PMCR_EL0 is added to the list of registers that are
saved and restored during a world switch.

Similar changes are made for PMCR for the AArch32 execution state.

NOTE: secure world code at lower ELs that assume other values in PMCR_EL0
will be impacted.

Change-Id: Iae40e8c0a196d74053accf97063ebc257b4d2f3a
Signed-off-by: David Cunado <david.cunado@arm.com>