GitLab

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

All the m0 code run in SRAM before, but we need to watch PMU_POWER_ST
when SOC enter into FSM, and SRAM will shutdown during this time, so
this code need run in PMUSRAM. But PMUSRAM only 8K space, we can not
put all the m0 binary into PMUSRAM, Split the M0 binary into two, dram
part still run in SRAM, and suspend part run in PMUSRAM.

Change-Id: Ie08bdf3e2b8838f12b9297fe60ab0aad219684b1
Signed-off-by: Lin Huang <hl@rock-chips.com>

Ensure (where possible) that switch statements in plat comply with MISRA
rules 16.1 - 16.7.

Change-Id: Ie4a7d2fd10f6141c0cfb89317ea28a755391622f
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>

This fix modifies the order of system includes to meet the ARM TF coding
standard. There are some exceptions to this change in order to retain
header groupings and where there are headers within #if statements.

Change-Id: Ib5b668c992d817cc860e97b29e16ef106d17e404
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>

The differential signal of DQS need keep low level
before gate training. It need enable RPULL and disable
PHY side ODT to ensure it when do gate training.
But it can not access the PHY registers to do it when
perform DFS.So the workaroud as below: It is ensure that
the PHY's read gate is landing somewhere in the incoming
DQS's pulses before it starts searching for pre-amble window.
It need get the rddqs_delay_ps to calculate the start point
of gate training for DFS.

Change-Id: I79eabcf4ec9a9c8f4539f68a51f22afba49c72fe
Signed-off-by: Lin Huang <hl@rock-chips.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

The printf() isn't used by the firmware itself, just by the tools under
the ./tools/ folder. Then tf_printf will unconditionally print.
Remove the unused print_dram_status_info() function.

Change-Id: Ie699ccb54a5be9a2cbbd7b8d4193b57075a2f57a
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This fixes code that set a tFC value in a register using the tRFC
value instead.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The F1 CAS latency setting was not bit shifted, which resulted in
setting the DRAM additive latency value instead.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

On resume, we use the DFS hardware to switch frequency index,
followed by a full training sequence on that index. Leaving
the DFS training modules enabled causes issues with the full
training done at resume. We also only needs these enabled
during a call to ddr_set_rate during runtime, so there's no
issue disabling them at the end of ddr_set_rate.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This moves the setting of the DQS drive strength to the M0 to minimize
the impact on DDR transactions. We need to have the DQS drive strength
changed for data training, which is triggered by the M0, but it also
needs to be changed back when data training is finished.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes an optimization to not recalculate parameters if the
frequency index being switched to hold the next frequency. This is
because some registers do not have a copy per frequency index, so this
optimization might be causing problems.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This patch do following things:
1. Request hresetn_cm0s_pmu_req first then request
   poresetn_cm0s_pmu_req during M0 enable.
2. Do not diable M0 clock for ddr dvfs.
3. Correct the clk_pmum0_gating_dis bit, it is BIT0 not BIT1
4. do not set/clear hclk_noc_pmu_en in M0 code, it does not relate
   to the M0 clock.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The phy pll needs to get 2X frequency to the DDR, so set the
pll_postdiv to 0.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

For ddr dfs stable, We need to enable ddr CA training
when do ddr dfs.
Signed-off-by: Lin Huang <hl@rock-chips.com>

This enables per CS training at 666MHz and above for ddrfreq per
vendor recommendation. Since the threshold was used for latency was
the same value, this also adds a new value for that.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This patch sets the frequency configuration of the next DRAM DFS index
to the configuration of the current index. This does not perform a
frequency transition. It just configures registers so the training on
resume for both indices will be correct.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

We used dcf do ddr frequency scaling, but we just include a dcf
binary, it hard to maintain later, we have M0 compile flow in ATF,
and M0 can also work for ddr frequency scaling, so let's use it.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

when dram frequency below 260MHz, phy master dll may unlock, so
let phy master dll working at dll bypass mode when frequency is
below 260MHz.
Signed-off-by: Lin Huang <hl@rock-chips.com>

we can reuse the dram config from loader, so we can remove dram_init()
and dts_timing_receive() funciton in dram.c, add the dram_set_odt_pd()
function to get the odt and auto power down parameter from kernel.

This also removes the dcf_code_init function to allow the system to
actually boot.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This changes the style of dmc register accesses to be a read/write on
a base address plus a register offset instead of reinterpretting a
base address as a struct and accessing members within that struct.

Change-Id: Iead097cd6afdb830d8bc193608cd39d01ce5a6bc
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This renames dram.c and dram.h to dfs.c and dfs.h respectively. This
is to make room for common functionality between frequency scaling and
suspend code for the DRAM in a pair of common files named dram.c and
dram.h. It also removes a duplicate enum definition from
dram_spec_timing.h

Change-Id: Ibfa1041f8781401f9d27901fe8c61862bcb05562
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

for compatible 32bit and 64bit, we use 0x82xxxxxx as function ID,
we modify SIP call function return value to 32 bit.

Change-Id: Ib99b03a9ea423853aaa296dcc634ee82c622a552

add auto_pd_dis_freq parameter, we can pass a frequency from kernel
to disable or enable ddr auto power down function.

Change-Id: Ie30914701336c59047c380381c6b75dd76a89562

add dram driver, and kernel can through sip function talk to bl31 to
do ddr frequency scaling. and ddr auto powerdown.

Change-Id: I0d0f2869aed95e336c6e23ba96a9310985c84840