Skip to content

GitLab

Switch branch/tag
  1. 04 Sep, 2018 10 commits
    • Bryan O'Donoghue's avatar
      imx: imx_io_mux: Define an IO-mux layer · 965bda4d
      Bryan O'Donoghue authored 
      

This patch defines:

- The full range of IO-mux register offsets relative to the base address of
  the IO-mux block base address.

- The bits for muxing the UART1 TX/RX lines.

- The bits for muxing the UART6 TX/RX lines.

- The pad control pad bits for the UART

Two functions are provided to configure pad muxes:

- void io_muxc_set_pad_alt_function(pad_mux_offset, alt_function)
  Takes a pad_mux_offset and sets the alt_function bit-mask supplied.
  This will have the effect of switching the pad into one of its defined
  peripheral functions. These peripheral function modes are defined in the
  NXP documentation and need to be referred to in order to correctly
  configure a new alternative-function.

- void io_muxc_set_pad_features(pad_feature_offset, pad_features)
  Takes a pad_feature_offset and applies a pad_features bit-mask to the
  indicated pad.
  This function allows the setting of PAD drive-strength, pull-up values,
  hysteresis glitch filters and slew-rate settings.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      965bda4d
    • Bryan O'Donoghue's avatar
      imx7: imx7_clock: usb: Initialize the USB core clocks · ddfb773f
      Bryan O'Donoghue authored 
      

This patch initializes USB core clocks for the i.MX7.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      ddfb773f
    • Bryan O'Donoghue's avatar
      imx7: imx7_clock: wdog: Initialize the watchdog clocks · 5ff1751d
      Bryan O'Donoghue authored 
      

This patch initializes the watchdog clocks for the i.MX7.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      5ff1751d
    • Bryan O'Donoghue's avatar
      imx7: imx7_clock: uart: Add UART clock init logic · 73f432a4
      Bryan O'Donoghue authored 
      

This patch adds an internal UART init routine that gets called from the
external facing clock init function.

In the first pass this call does an explicit disable of all UART
clock-gates. Later changes will enable only the UART clock-gates we care
about.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      73f432a4
    • Bryan O'Donoghue's avatar
      imx: imx_clock: usb: Add USB clock API · 6176a4e5
      Bryan O'Donoghue authored 
      

This set of patches adds a very minimal layer of USB enabling patches to
clock.c. Unlike the watchdog or UART blocks the USB clocks pertain to PHYs,
the main USB clock etc, not to different instances of the same IP block.

As a result this patch-set takes the clock CCGR clock identifier directly
rather than as an index of an instance of blocks of the same type.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      6176a4e5
    • Bryan O'Donoghue's avatar
      imx: imx_clock: wdog: Add watchdog clock API · bbdcdd04
      Bryan O'Donoghue authored 
      

This patch adds a set of functions to enable the clock for each of the
watchdog IP blocks.

Unlike the MMC and UART blocks, the watchdog blocks operate off of the one
root clock, only the clock-gates are enable/disabled individually.

As a consequence the function clock_set_wdog_clk_root_bits() is used to set
the root-slice just once for all of the watchdog blocks.

Future implementations may need to change this model but for now on the one
supported processor and similar NXP SoCs this model should work fine.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      bbdcdd04
    • Jun Nie's avatar
      imx: imx_clock: mmc: Add USDHC clock API · 14cf32aa
      Jun Nie authored 
      

This patch adds an API to configure up the base USDHC clocks, taking a
bit-mask of silicon specific bits as an input from a higher layer in order
to direct the necessary clock source.
Signed-off-by: default avatarJun Nie <jun.nie@linaro.org>
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      14cf32aa
    • Bryan O'Donoghue's avatar
      imx: imx_clock: uart: Add UART clock API · dcd54e9b
      Bryan O'Donoghue authored 
      

This patch adds an API to configure up the base UART clocks, taking a
bit-mask of silicon specific bits as an input from a higher layer in order
to direct the necessary clock source.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      dcd54e9b
    • Bryan O'Donoghue's avatar
      imx: imx_clock: Add driver and associated clock register definitions · 82e35083
      Bryan O'Donoghue authored 
      

This commit:

- Defines a clock stub with a conjoined header defining the clock
  memory map.

- Defines the CCM Clock Gating Register which comes in a quadrumvirate
  register set to read, set, clear and toggle individual clock gates into
  one of four states based bitmask.

  00: Domain clocks not needed
  01: Domain clocks needed when in RUN
  10: Domain clocks needed when in RUN and WAIT
  11: Domain clocks needed all the time

- Defines clock control register bits

  There are various quadrumvirate register blocks target-root, misc-root,
  post-root, pre-root in the CCM.

  The number of registers is huge but the four registers in each
  quadrumvirate block contain the same bits, so the number of bit
  definitions is actually quite low.

- Defines clock identifiers

  An array of clock gates is provided in the CCM block. In order to index
  that array and thus enable/disable clock gates for the right components,
  we need to provide meaningful names to the indices.

  Section 5.2.5 of the i.MX7 Solo Application Processor Reference Manual
  Rev 0.1 provides the relevant details.

- Defines target mux select bits
  This is a comprehensive definition of the target clock mux select bits.
  These bits are required to correctly select the clock source. Defining
  all of the bits up-front even for unused blocks in ATF means we can
  switch on any block we want at a later date without having to write new
  code in the clock-mux layer.

- Defines identifier indices into root-slice array
  The root-slice array of control registers has a specific set of indices,
  which differ from the clock-gate indices.

- Provides a clock gate enable/disable routine
  Provides a clock-gate enable/disable routine via the set/clr
  registers in a given clock-gate control register block.

  This index passed should be one of the enums associated with CCM and
  depending on enable/disable being passed either set or clr will be
  written to.

  The Domain0 bits are currently the only bits targeted by this write, more
  work may need to be done on the domain bits in subsequent patches as a
  result.

- imx: Adds set/clr routines to clock layer

  Adds a set and clr routine to the clock layer. These routines allow us to
  access the set and clear registers of the "target" block registers. These
  are the registers where we select the clock source from the available list.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      82e35083
    • Bryan O'Donoghue's avatar
      imx7: imx_regs: Add a shared imx-regs.h for i.MX7 ATF platforms · 7d464592
      Bryan O'Donoghue authored 
      

In order to have some common code shared between similar SOCs its pretty
common to have IP blocks reused. In reusing those blocks we frequently need
to map compatible blocks to different addresses depending on the SOC.

This patch adds a basic memory map of the i.MX7 based on the "Cortex-A7
Memory Map" section 2.12 of "i.MX7Solo Applications Processor Reference
Manual, Rev 0.1 08/2016"

In memory map terms the i.MX7S and i.MX7D are identical with the D
variant containing two Cortex-A7 cores plus a Cortex-M core and the S
variant containing one Cortex-A7 and one Cortex-M.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      7d464592
  3. 30 Aug, 2018 3 commits
  5. 23 Aug, 2018 1 commit
  7. 22 Aug, 2018 10 commits
  9. 21 Aug, 2018 1 commit
  11. 20 Aug, 2018 1 commit
  13. 19 Aug, 2018 1 commit
  15. 17 Aug, 2018 1 commit
  17. 15 Aug, 2018 2 commits
  19. 10 Aug, 2018 6 commits
  21. 06 Aug, 2018 1 commit
  23. 03 Aug, 2018 3 commits