GitLab

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size reserved for BL2 has been increased.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This reverts commit 2f18aa1f

.

It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.

Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The bounds check in ARM_CASSERT_MMAP does not take into account the
array sentinel in plat_arm_mmap. This commit fixes this, and adds an
additional check to ensure the number of entries in the array is
within the bounds of PLAT_ARM_MMAP_ENTRIES.

Change-Id: Ie6df10c0aa0890d62826bc3224ad7b3e36fd53e2
Signed-off-by: Chris Kay <chris.kay@arm.com>

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size of BL31 has been increased in builds with SPM.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.

The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.

Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.

This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>

This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.

The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.

Fixes ARM-software/tf-issues#559

Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.3: All declarations of an object or function shall
          use the same names and type qualifiers.

Fixed for:

	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I48201c9ef022f6bd42ea8644529afce70f9b3f22
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.

Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.

Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.

The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:

	--data cluster0.cpu0=bl2.bin@0x4001000
	-C cluster0.cpu0.RVBAR=0x4001000

These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.

Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Factor out SPE operations in a separate file.  Use the publish
subscribe framework to drain the SPE buffers before entering secure
world.  Additionally, enable SPE before entering normal world.

A side effect of this change is that the profiling buffers are now
only drained when a transition from normal world to secure world
happens.  Previously they were drained also on return from secure
world, which is unnecessary as SPE is not supported in S-EL1.

Change-Id: I17582c689b4b525770dbb6db098b3a0b5777b70a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

The function arm_validate_ns_entrypoint() validates a given non-secure
physical address. This function however specifically returns PSCI error
codes.

Non-secure physical address validation is potentially useful across ARM
platforms, even for non-PSCI use cases. Therefore make this function
common by returning 0 for success or -1 otherwise.

Having made the function common, make arm_validate_psci_entrypoint() a
wrapper around arm_validate_ns_entrypoint() which only translates return
value into PSCI error codes. This wrapper is now used where
arm_validate_ns_entrypoint() was currently used for PSCI entry point
validation.

Change-Id: Ic781fc3105d6d199fd8f53f01aba5baea0ebc310
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Provides GICv3 save/restore feature to arm_system_pwr_domain_resume and
arm_system_pwr_domain_save functions.

Introduce FVP PSCI power level 3 (System level) support. This is solely
done to provide example code on how to use the GICv3 save and restore
helpers.

Also make CSS GICv3 platforms power off the Redistributor on SYSTEM
SUSPEND as its state is saved and restored.

Change-Id: I0d852f3af8824edee1a17c085cf593ddd33a4e77
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Co-Authored-by: Douglas Raillard <douglas.raillard@arm.com>

mem_protect needs some kind of non-volatile memory because it has
to remember its state across reset and power down events.
The most suitable electronic part for this feature is a NVRAM
which should be only accesible from the secure world. Juno and
FVP lack such hardware and for this reason the MEM_PROTECT
functionality is implemented with Flash EEPROM memory on both
boards, even though this memory is accesible from the non-secure
world. This is done only to show a full implementation of
these PSCI features, but an actual system shouldn't use a
non-secure NVRAM to implement it.

The EL3 runtime software will write the mem_protect flag and BL2
will read and clear the memory ranges if enabled. It is done in
BL2 because it reduces the time that TF needs access to the full
non-secure memory.

The memory layout of both boards is defined using macros which
take different values in Juno and FVP platforms. Generic platform
helpers are added that use the platform specific macros to generate
a mem_region_t that is valid for the platform.

Change-Id: I2c6818ac091a2966fa07a52c5ddf8f6fde4941e9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

The current definition of ARM_INSTANTIATE_LOCK macro includes a
semicolon, which means it's omitted where it's used. This is anomalous
for a C statement in global scope.

Fix this by removing semicolon from the definition; and where it's a
NOP, declare a file-scoped variable explicitly tagged as unused to avoid
compiler warning.

No functional changes.

Change-Id: I2c1d92ece4777e272a025011e03b8003f3543335
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

SPE is only supported in non-secure state.  Accesses to SPE specific
registers from SEL1 will trap to EL3.  During a world switch, before
`TTBR` is modified the SPE profiling buffers are drained.  This is to
avoid a potential invalid memory access in SEL1.

SPE is architecturally specified only for AArch64.

Change-Id: I04a96427d9f9d586c331913d815fdc726855f6b0
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

On ARM platforms before exiting from SP_MIN ensure that
the default console is switched to the runtime serial port.

Change-Id: I0ca0d42cc47e345d56179eac16aa3d6712767c9b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

This patch adds the SCMI driver for communicating with SCP. The power
domain management and system power management protocol of the SCMI
specification[1] is implemented in the driver. The SCP power management
abstraction layer for SCMI for CSS power management is also added.

A new buid option `CSS_USE_SCMI_DRIVER` is introduced to select SCMI
driver over SCPI.

[1] ARM System Control and Management Interface v1.0 (SCMI)
Document number: ARM DEN 0056A

Change-Id: I67265615a17e679a2afe810b9b0043711ba09dbb
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

In AArch64, privileged exception levels control the execution state
(a.k.a. register width) of the immediate lower Exception Level; i.e.
whether the lower exception level executes in AArch64 or AArch32 state.
For an exception level to have its execution state changed at run time,
it must request the change by raising a synchronous exception to the
higher exception level.

This patch implements and adds such a provision to the ARM SiP service,
by which an immediate lower exception level can request to switch its
execution state. The execution state is switched if the request is:

  - raised from non-secure world;

  - raised on the primary CPU, before any secondaries are brought online
    with CPU_ON PSCI call;

  - raised from an exception level immediately below EL3: EL2, if
    implemented; otherwise NS EL1.

If successful, the SMC doesn't return to the caller, but to the entry
point supplied with the call. Otherwise, the caller will observe the SMC
returning with STATE_SW_E_DENIED code. If ARM Trusted Firmware is built
for AArch32, the feature is not supported, and the call will always
fail.

For the ARM SiP service:

  - Add SMC function IDs for both AArch32 and AArch64;
  - Increment the SiP service minor version to 2;
  - Adjust the number of supported SiP service calls.

Add documentation for ARM SiP service.

Fixes ARM-software/tf-issues#436

Change-Id: I4347f2d6232e69fbfbe333b340fcd0caed0a4cea
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

utils.h is included in various header files for the defines in it.
Some of the other header files only contain defines.  This allows the
header files to be shared between host and target builds for shared defines.

Recently types.h has been included in utils.h as well as some function
prototypes.

Because of the inclusion of types.h conflicts exist building host tools
abd these header files now.  To solve this problem,
move the defines to utils_def.h and have this included by utils.h and
change header files to only include utils_def.h and not pick up the new
types.h being introduced.

Fixes ARM-software/tf-issues#461
Signed-off-by: Scott Branden <scott.branden@broadcom.com>

Remove utils_def.h from utils.h

This patch removes utils_def.h from utils.h as it is not required.
And also makes a minor change to ensure Juno platform compiles.

Change-Id: I10cf1fb51e44a8fa6dcec02980354eb9ecc9fa29

This patch adds support for SP_MIN on JUNO platform.
The changes include addition of AArch32 assembly files,
JUNO specific SP_MIN make file and miscellaneous changes
in ARM platform files to enable support for SP_MIN.

Change-Id: Id1303f422fc9b98b9362c757b1a4225a16fffc0b
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Following steps are required to boot JUNO in AArch32 state:
1> BL1, in AArch64 state, loads BL2.
2> BL2, in AArch64 state, initializes DDR.
  Loads SP_MIN & BL33 (AArch32 executable)images.
  Calls RUN_IMAGE SMC to go back to BL1.
3> BL1 writes AArch32 executable opcodes, to load and branch
  at the entrypoint address of SP_MIN, at HI-VECTOR address and
  then request for warm reset in AArch32 state using RMR_EL3.

This patch makes following changes to facilitate above steps:
* Added assembly function to carry out step 3 above.
* Added region in TZC that enables Secure access to the
  HI-VECTOR(0xFFFF0000) address space.
* AArch32 image descriptor is used, in BL2, to load
  SP_MIN and BL33 AArch32 executable images.

A new flag `JUNO_AARCH32_EL3_RUNTIME` is introduced that
controls above changes. By default this flag is disabled.

NOTE: BL1 and BL2 are not supported in AArch32 state for JUNO.

Change-Id: I091d56a0e6d36663e6d9d2bb53c92c672195d1ec
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

ARM platforms have migrated to the translation tables library v2.
However, for testing purposes, it can be useful to temporarily switch
back to the old version.

This patch introduces the option `ARM_XLAT_TABLES_LIB_V1`, that switches
to v1 of the library when is set to 1. By default, it is 0, so that ARM
platforms use the new version unless specifically stated.

Updated User Guide.

Change-Id: I53d3c8dd97706f6af9c6fca0364a88ef341efd31
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch modifies some of the functions in ARM platform layer to cater
for the case when multi-threading `MT` is set in MPIDR. A new build flag
`ARM_PLAT_MT` is added, and when enabled, the functions accessing MPIDR
now assume that the `MT` bit is set for the platform and access the bit
fields accordingly.

Also, a new API plat_arm_get_cpu_pe_count is added when `ARM_PLAT_MT` is
enabled, returning the PE count within the physical cpu corresponding to
`mpidr`.

Change-Id: I04ccf212ac3054a60882761f4087bae299af13cb
Signed-off-by: Summer Qin <summer.qin@arm.com>

Modify ARM common makefile to use version 2 of the translation tables
library and include the new header in C files.

Simplify header dependencies related to this library to simplify the
change.

The following table contains information about the size increase in
bytes for BL1 after applying this patch. The code has been compiled for
different configurations of FVP in AArch64 mode with compiler GCC 4.9.3
20150413. The sizes have been calculated with the output of `nm` by
adding the size of all regions and comparing the total size before and
after the change. They are sumarized in the table below:

                               text   bss   data  total
        Release                +660   -20    +88   +728
        Debug                  +740   -20   +242   +962
        Debug (LOG_LEVEL=50)  +1120   -20   +317  +1417

Change-Id: I539e307f158ab71e3a8b771640001fc1bf431b29
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Due to incorrect conditional compilation checks, bakery locks were
excluded from the CCN driver and the power controller driver for FVP
when BL32 was built as the EL3 Runtime Software in AArch32 mode.
This patch corrects the same.

Change-Id: Ib1f163d9167a5c38e4d622232c4835cad9c235aa
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

One nasty part of ATF is some of boolean macros are always defined
as 1 or 0, and the rest of them are only defined under certain
conditions.

For the former group, "#if FOO" or "#if !FOO" must be used because
"#ifdef FOO" is always true.  (Options passed by $(call add_define,)
are the cases.)

For the latter, "#ifdef FOO" or "#ifndef FOO" should be used because
checking the value of an undefined macro is strange.

Here, IMAGE_BL* is handled by make_helpers/build_macro.mk like
follows:

  $(eval IMAGE := IMAGE_BL$(call uppercase,$(3)))

  $(OBJ): $(2)
          @echo "  CC      $$<"
          $$(Q)$$(CC) $$(TF_CFLAGS) $$(CFLAGS) -D$(IMAGE) -c $$< -o $$@

This means, IMAGE_BL* is defined when building the corresponding
image, but *undefined* for the other images.

So, IMAGE_BL* belongs to the latter group where we should use #ifdef
or #ifndef.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

As with other ARM platform GIC APIs, these directly invoke the GICv3
driver APIs for Redistributor power management.

For the sake of uniform GIC API, empty stubs are placed for those GIC
drivers that lack Redistributor component.

Change-Id: Iad0d760d4dbca790998f7768cda621ff3b15a864
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The capabilities exposed by the PSCI generic layer depends on the hooks
populated by the platform in `plat_arm_psci_pm_ops`. Currently ARM
Standard platforms statically define this structure. However, some
platforms may want to modify the hooks at runtime before registering
them with the generic layer.

This patch introduces a new ARM platform layer API
`plat_arm_psci_override_pm_ops` which allows the platform to probe
the power controller and modify `plat_arm_psci_pm_ops` if required.
Consequently, 'plat_arm_psci_pm_ops' is no longer qualified as
`const` on ARM Standard platforms.

Change-Id: I7dbb44b7bd36c20ec14ded5ee45a96816ca2ab9d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds support in SP_MIN to receive generic and
platform specific arguments from BL2.

The new signature is as following:
    void sp_min_early_platform_setup(void *from_bl2,
         void *plat_params_from_bl2);

ARM platforms have been modified to use this support.

Note: Platforms may break if using old signature.
      Default value for RESET_TO_SP_MIN is changed to 0.

Change-Id: I008d4b09fd3803c7b6231587ebf02a047bdba8d0

This patch adds changes in ARM platform code to use new
version of image loading.

Following are the major changes:
  -Refactor the signatures for bl31_early_platform_setup()
   and arm_bl31_early_platform_setup() function to use
   `void *` instead of `bl31_params_t *`.
  -Introduce `plat_arm_bl2_handle_scp_bl2()` to handle
   loading of SCP_BL2 image from BL2.
  -Remove usage of reserve_mem() function from
   `arm_bl1_early_platform_setup()`
  -Extract BL32 & BL33 entrypoint info, from the link list
   passed by BL2, in `arm_bl31_early_platform_setup()`
  -Provides weak definitions for following platform functions:
     plat_get_bl_image_load_info
     plat_get_next_bl_params
     plat_flush_next_bl_params
     bl2_plat_handle_post_image_load
  -Instantiates a descriptor array for ARM platforms
   describing image and entrypoint information for
   `SCP_BL2`, `BL31`, `BL32` and `BL33` images.

All the above changes are conditionally compiled using the
`LOAD_IMAGE_V2` flag.

Change-Id: I5e88b9785a3df1a2b2bbbb37d85b8e353ca61049

This patch adds a couple of missing forward declarations in plat_arm.h
so that all types it references are known within this header file,
without relying on previous header inclusions. This concerns the
meminfo and bl31_params structures, which are defined in bl_common.h.
Other external types referenced from plat_arm.h (e.g. mmap_region_t)
get declared through header files included by arm_plat.h so they
don't need forward declarations.

Change-Id: I471d5aa487919aff3fa979fc65e053f4f5b0ef32

This patch implements the support for SP_MIN in FVP. The SP_MIN platform
APIs are implemented and the required makefile support is added for FVP.

Change-Id: Id50bd6093eccbd5e38894e3fd2b20d5baeac5452

This patch reworks type usage in generic code, drivers and ARM platform files
to make it more portable. The major changes done with respect to
type usage are as listed below:

* Use uintptr_t for storing address instead of uint64_t or unsigned long.
* Review usage of unsigned long as it can no longer be assumed to be 64 bit.
* Use u_register_t for register values whose width varies depending on
  whether AArch64 or AArch32.
* Use generic C types where-ever possible.

In addition to the above changes, this patch also modifies format specifiers
in print invocations so that they are AArch64/AArch32 agnostic. Only files
related to upcoming feature development have been reworked.

Change-Id: I9f8c78347c5a52ba7027ff389791f1dad63ee5f8

The arm_setup_page_tables() function used to expect a single set of
addresses defining the extents of the whole read-only section, code
and read-only data mixed up, which was mapped as executable.

This patch changes this behaviour. arm_setup_page_tables() now
expects 2 separate sets of addresses:

 - the extents of the code section;
 - the extents of the read-only data section.

The code is mapped as executable, whereas the data is mapped as
execute-never. New #defines have been introduced to identify the
extents of the code and the read-only data section. Given that
all BL images except BL1 share the same memory layout and linker
script structure, these #defines are common across these images.
The slight memory layout differences in BL1 have been handled by
providing values specific to BL1.

Note that this patch also affects the Xilinx platform port, which
uses the arm_setup_page_tables() function. It has been updated
accordingly, such that the memory mappings on this platform are
unchanged. This is achieved by passing null values as the extents
of the read-only data section so that it is ignored. As a result,
the whole read-only section is still mapped as executable.

Fixes ARM-software/tf-issues#85

Change-Id: I1f95865c53ce6e253a01286ff56e0aa1161abac5

This patch introduces a new header file: include/lib/utils.h.
Its purpose is to provide generic macros and helper functions that
are independent of any BL image, architecture, platform and even
not specific to Trusted Firmware.

For now, it contains only 2 macros: ARRAY_SIZE() and
IS_POWER_OF_TWO(). These were previously defined in bl_common.h and
xlat_tables.c respectively.

bl_common.h includes utils.h to retain compatibility for platforms
that relied on bl_common.h for the ARRAY_SIZE() macro. Upstream
platform ports that use this macro have been updated to include
utils.h.

Change-Id: I960450f54134f25d1710bfbdc4184f12c049a9a9