GitLab

This patch adds entries to the mem params array for

- BL32
- BL32_EXTRA1
- BL32_EXTRA2
- BL33
- HW_CONFIG_ID

BL32 is marked as bootable to indicate that OPTEE is the thing that should
be booted next.

In our model OPTEE chain-loads onto u-boot so only BL32 is bootable.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds support for parsing a FIP pre-loaded by a previous
boot-phase such as u-boot or via ATF reading directly from eMMC.

[bod: squashing several patches from Rui, Jun and bod]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch defines a platform_def.h describing

- FIP layout and location
- eMMC device select
- UART identity select
- System clock frequency
- Operational memory map
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

In order to link even a basic image we need to declare
REGISTER_BL_IMAGE_DESCS. This patch declares an empty structure which is
passed to REGISTER_BL_IMAGE_DESCS(). Later patches will add in some
meaningful data.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Internal declarations for the WaRP7 port will go here. For now just include
sys/types.h.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds warp7_image_load.c with the functions

- plat_flush_next_bl_params()
- plat_get_bl_image_load_info()
- plat_get_next_bl_params()
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds a warp7_helpers.S which contains a implementation of:

- platform_mem_init
- plat_get_my_entrypoint
- plat_crash_console_init
- plat_crash_console_putc
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The watchdog block on the IMX is mercifully simple. This patch maps the
various registers and bits associated with the block.

We are mostly only really interested in the power-down-enable (PDE) bits in
the block for the purposes of ATF.

The i.MX7 Solo Applications Processor Reference Manual details the PDE bit
as follows:

"Power Down Enable bit. Reset value of this bit is 1, which means the power
down counter inside the WDOG is enabled after reset. The software must
write 0 to this bit to disable the counter within 16 seconds of reset
de-assertion. Once disabled this counter cannot be enabled again. See
Power-down counter event for operation of this counter."

This patch does that zero write in-lieu of later phases in the boot
no-longer have the necessary permissions to rewrite the PDE bit directly.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch defines the most basic part of the CAAM and the only piece of
the CAAM silicon we are really interested in, in ATF, the CAAM control
structure.

The CAAM itself is a huge address space of some 32k, way out of scope for
the purpose we have in ATF.

This patch adds a simple CAAM init function that assigns ownership of the
CAAM job-rings to the non-secure MID with the ownership bit set to
non-secure.

This will allow later logic in the boot process such as OPTEE, u-boot and
Linux to assign job-rings as appropriate, restricting if necessary but
leaving open the main functionality of the CAAM to the Linux NS runtime.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The High Assurance Boot or HAB is an on-chip method of providing a
root-of-trust from the reset vector to subsequent stages in the bootup
flow of the Cortex-A7 on the i.MX series of processors.

This patch adds a simple header file with pointer offsets of the provided
set of HAH API callbacks in the BootROM.

The relative offset of the function pointers is a constant and known
quantum, a software-contract between NXP and an implementation which is
defined in the NXP HAB documentation.

All we need is the correct base offset and then we can map the set of
function pointers relative to that offset.

imx_hab_arch.h provides the correct offset and the imx_hab.h hooks the
offset to the pre-determined callbacks.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>

In order to enable compile time differences in HAB interaction, we should
split out the definition of the base address of the HAB API.

Some version of the i.MX series have different offsets from the BootROM
base for the HAB callback table.

This patch defines the header into which we will define the i.MX7 specific
offset. The offset of the i.MX7 function-callback table is simultaneously
defined.

Once done, we can latch a set of common function pointer locations from the
offset given here and if necessary change the offset for different
processors without any other code-change.

For now all we support is i.MX7 so the only offset being defined is that
for the i.MX7.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>

This patch adds snvs.c with a imx_snvs_init() function.

imx_snvs_init() sets up permissions of the RTC via the SNVS HPCOMR.

During previous work with OPTEE on the i.MX7 part we discovered that prior
to switching from secure-world to normal-world it is required to apply more
permissive permissions than are defaulted to in order for Linux to be able
to access the RTC and CAAM functionality in general.

This patch pertains to fixing the RTC permissions by way of the
HPCOMR.NPSWA_EN bit.

Once set non-privileged code aka Linux-kernel code has permissions to
access the SNVS where the RTC resides.

Perform that permissions fix in imx_snvs_init() now, with a later patch making
the call from our platform setup code.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit defines two things.

- The basic SNVS memory map. At the moment that is total overkill for the
  permission bits we need to set inside the SNVS but, for the sake of
  completeness define the whole SNVS area as a struct.

- The bits of the HPCOMR register

  A permission fix will need to be applied to the SNVS block prior to
  switching on TrustZone. All we need to do is waggle a bit in the HPCOMR
  register. To do that waggle we first need to define the bits of the
  HPCOMR register.

- A imx_snvs_init() function definition

  Declare the snvs_init() function so that it can be called from our
  platform setup code.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

- Add a header to define imx_csu_init().
- Defines the Central Security Unit's Config Security Level
  permission bits.
- Define CSU_CSL_OPEN_ACCESS permission bitmask
- Run a loop to setup peripheral CSU permissions
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an initial AHB-to-IP TrustZone (AIPS-TZ) initialization
routine. Setting up the AIPSTZ controller is required to inform the SoC
interconnect fabric which bus-masters can read/write and if the read/writes
are buffered.

For our purposes the initial configuration is for everything to be open. We
can lock-down later on as necessary.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch defines:

- The full range of IO-mux register offsets relative to the base address of
  the IO-mux block base address.

- The bits for muxing the UART1 TX/RX lines.

- The bits for muxing the UART6 TX/RX lines.

- The pad control pad bits for the UART

Two functions are provided to configure pad muxes:

- void io_muxc_set_pad_alt_function(pad_mux_offset, alt_function)
  Takes a pad_mux_offset and sets the alt_function bit-mask supplied.
  This will have the effect of switching the pad into one of its defined
  peripheral functions. These peripheral function modes are defined in the
  NXP documentation and need to be referred to in order to correctly
  configure a new alternative-function.

- void io_muxc_set_pad_features(pad_feature_offset, pad_features)
  Takes a pad_feature_offset and applies a pad_features bit-mask to the
  indicated pad.
  This function allows the setting of PAD drive-strength, pull-up values,
  hysteresis glitch filters and slew-rate settings.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch initializes USB core clocks for the i.MX7.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch initializes the watchdog clocks for the i.MX7.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an internal UART init routine that gets called from the
external facing clock init function.

In the first pass this call does an explicit disable of all UART
clock-gates. Later changes will enable only the UART clock-gates we care
about.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This set of patches adds a very minimal layer of USB enabling patches to
clock.c. Unlike the watchdog or UART blocks the USB clocks pertain to PHYs,
the main USB clock etc, not to different instances of the same IP block.

As a result this patch-set takes the clock CCGR clock identifier directly
rather than as an index of an instance of blocks of the same type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds a set of functions to enable the clock for each of the
watchdog IP blocks.

Unlike the MMC and UART blocks, the watchdog blocks operate off of the one
root clock, only the clock-gates are enable/disabled individually.

As a consequence the function clock_set_wdog_clk_root_bits() is used to set
the root-slice just once for all of the watchdog blocks.

Future implementations may need to change this model but for now on the one
supported processor and similar NXP SoCs this model should work fine.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an API to configure up the base USDHC clocks, taking a
bit-mask of silicon specific bits as an input from a higher layer in order
to direct the necessary clock source.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an API to configure up the base UART clocks, taking a
bit-mask of silicon specific bits as an input from a higher layer in order
to direct the necessary clock source.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit:

- Defines a clock stub with a conjoined header defining the clock
  memory map.

- Defines the CCM Clock Gating Register which comes in a quadrumvirate
  register set to read, set, clear and toggle individual clock gates into
  one of four states based bitmask.

  00: Domain clocks not needed
  01: Domain clocks needed when in RUN
  10: Domain clocks needed when in RUN and WAIT
  11: Domain clocks needed all the time

- Defines clock control register bits

  There are various quadrumvirate register blocks target-root, misc-root,
  post-root, pre-root in the CCM.

  The number of registers is huge but the four registers in each
  quadrumvirate block contain the same bits, so the number of bit
  definitions is actually quite low.

- Defines clock identifiers

  An array of clock gates is provided in the CCM block. In order to index
  that array and thus enable/disable clock gates for the right components,
  we need to provide meaningful names to the indices.

  Section 5.2.5 of the i.MX7 Solo Application Processor Reference Manual
  Rev 0.1 provides the relevant details.

- Defines target mux select bits
  This is a comprehensive definition of the target clock mux select bits.
  These bits are required to correctly select the clock source. Defining
  all of the bits up-front even for unused blocks in ATF means we can
  switch on any block we want at a later date without having to write new
  code in the clock-mux layer.

- Defines identifier indices into root-slice array
  The root-slice array of control registers has a specific set of indices,
  which differ from the clock-gate indices.

- Provides a clock gate enable/disable routine
  Provides a clock-gate enable/disable routine via the set/clr
  registers in a given clock-gate control register block.

  This index passed should be one of the enums associated with CCM and
  depending on enable/disable being passed either set or clr will be
  written to.

  The Domain0 bits are currently the only bits targeted by this write, more
  work may need to be done on the domain bits in subsequent patches as a
  result.

- imx: Adds set/clr routines to clock layer

  Adds a set and clr routine to the clock layer. These routines allow us to
  access the set and clear registers of the "target" block registers. These
  are the registers where we select the clock source from the available list.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

In order to have some common code shared between similar SOCs its pretty
common to have IP blocks reused. In reusing those blocks we frequently need
to map compatible blocks to different addresses depending on the SOC.

This patch adds a basic memory map of the i.MX7 based on the "Cortex-A7
Memory Map" section 2.12 of "i.MX7Solo Applications Processor Reference
Manual, Rev 0.1 08/2016"

In memory map terms the i.MX7S and i.MX7D are identical with the D
variant containing two Cortex-A7 cores plus a Cortex-M core and the S
variant containing one Cortex-A7 and one Cortex-M.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

tf_printf and tf_snprintf are now called printf and snprintf, so the
code needs to be updated.

Change-Id: Iffeee97afcd6328c4c2d30830d4923b964682d71
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The codebase was using non-standard headers. It is needed to replace
them by the correct ones so that we can use the new libc headers.

Change-Id: I530f71d9510cb036e69fe79823c8230afe890b9d
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Also change header guards to fix defects of MISRA C-2012 Rule 21.1.

Change-Id: Ied0d4b0e557ef6119ab669d106d2ac5d99620c57
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Add domain suspend/resume support, Linux kernel
can "echo mem > /sys/power/state" to put system
into suspend mode, all CPUs and cluster will be
powered off and can be waked up if irq pending
in GIC, tested on i.MX8QM MEK board.

Since the power state has been implemented, switch
to use standard power state for CCI operations
instead of private cpu use count in i.MX8QM.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Add domain off support for Linux kernel's cpu
hot-plug feature, when there are cpu off request
from Linux kernel, TF-A will send command to
system controller to do CPU power gate accordingly,
tested on i.MX8QM MEK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Add system reset support for i.MX8QM,
when Linux kernel issues "reboot" command,
TF-A will send command to inform system
controller to reset whole board according
to board design, tested on i.MX8QM MEK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Add system power off support for i.MX8QM,
when Linux kernel issues "poweroff" command,
TF-A will send command to inform system
controller to power off whole board according
to board design, tested on i.MX8QM MEK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Add domain suspend/resume support, Linux kernel
can "echo mem > /sys/power/state" to put system
into suspend mode, all CPUs and cluster will be
powered off and can be waked up if irq pending
in GIC, tested on i.MX8QX MEK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Add domain off support for Linux kernel's cpu
hot-plug feature, when there are cpu off request
from Linux kernel, TF-A will send command to
system controller to do CPU power gate accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Add system reset support for i.MX8QX,
when Linux kernel issues "reboot" command,
TF-A will send command to inform system
controller to reset whole board according
to board design, tested on i.MX8QX MEK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Add system power off support for i.MX8QX,
when Linux kernel issues "poweroff" command,
TF-A will send command to inform system
controller to power off whole board according
to board design, tested on i.MX8QX MEK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

NXP's i.MX8QM is an ARMv8 SoC with 2 clusters, 2 Cortex-A72
cores in one cluster and 4 Cortex-A53 in the other cluster,
and also has system controller (Cortex-M4) inside, documentation
can be found in below link:

https://www.nxp.com/products/processors-and-microcontrollers/


applications-processors/i.mx-applications-processors/i.mx-8-processors:IMX8-SERIES

This patch adds support for booting up SMP linux kernel (v4.9).
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

NXP's i.MX8QX is an ARMv8 SoC with 4 Cortex-A35 cores and
system controller (Cortex-M4) inside, documentation can
be found in below link:

https://www.nxp.com/products/processors-and-microcontrollers/


applications-processors/i.mx-applications-processors/i.mx-8-processors:IMX8-SERIES

This patch adds support for booting up SMP linux kernel (v4.9).
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

This patch adds support for NXP's imx SoC common
function support like topology, gic implementation.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

Add NXP's imx SoC debug uart driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>