Skip to content

GitLab

Switch branch/tag
  1. 14 Nov, 2018 3 commits
    • Andre Przywara's avatar
      allwinner: power: add enable switches for DCDC1/5 · a561e41b
      Andre Przywara authored 
      

The DCDC1 and DCDC5 power rails didn't specify the enable bits. This
isn't critical, since those rails are on by default (and are needed for
every board), but it is inconsistent.

Add the respective enable bits for those two rails.
Signed-off-by: default avatarAndre Przywara <andre.przywara@arm.com>
      a561e41b
    • Andre Przywara's avatar
      allwinner: power: fix DRIVEVBUS pin setup · d93eb446
      Andre Przywara authored 
      

The DRIVEVBUS pin setup was broken in two ways:
- To configure this pin as an output pin, one has to *clear* the bit in
  register 0x8f. It is 0 by default, but rebooting from Linux might have
  left this bit set.
- Doing this just configures the pin as an output pin, but doesn't
  actually drive power to it. This is done via bit 2 in register 0x30.

Fix the routine to both properly configure the pin and drive power to
it. Add an axp_clrsetbits() helper on the way.

Now this isn't really perfect, still:
We only need to setup the PMIC power rails that are needed for U-Boot.
DRIVEVBUS typically controls the VBUS voltage for the host function of
an USB-OTG port, something we typically don't want in U-Boot (fastboot,
using the USB *device* functionality, is much more common). The
BananaPi-M64 uses the regulator in this way, but the Remix Mini PC
actually controls the power of both its USB ports via this line.

Technically we should differentiate here: if DRIVEVBUS controls a
microUSB-B socket, the power should stay off, any host-type A sockets
should be supplied, though.
For now just always enable the power, that shouldn't really hurt the
USB-OTG functionality anyway.
Signed-off-by: default avatarAndre Przywara <andre.przywara@arm.com>
      d93eb446
    • Andre Przywara's avatar
      allwinner: A64/H5: setup missing bus clocks · 19a7507a
      Andre Przywara authored 
      

The legacy Allwinner ATF port used to setup some clocks, and U-Boot is
still relying on this. We don't need to setup the full set, as the SPL
is doing most of it, but it misses one clock (AHB2) and programs another
(AHB1) to quite conservative values.

Fix this up during the platform setup to improve USB and Ethernet
performance, iperf values go up by 31% in my setup with that patch.
Signed-off-by: default avatarAndre Przywara <andre.przywara@arm.com>
      19a7507a
  3. 09 Nov, 2018 2 commits
    • Yann Gautier's avatar
      stm32mp1: correct some static analysis tools issues · 3e6fab43
      Yann Gautier authored 
      

These issues wer found by sparse:

drivers/st/clk/stm32mp1_clk.c:1524:19:
 warning: incorrect type in assignment (different base types)
    expected restricted fdt32_t const [usertype] *pkcs_cell
    got unsigned int const [usertype] *

plat/st/stm32mp1/plat_image_load.c:13:6:
 warning: symbol 'plat_flush_next_bl_params' was not declared.
 Should it be static?
plat/st/stm32mp1/plat_image_load.c:21:16:
 warning: symbol 'plat_get_bl_image_load_info' was not declared.
 Should it be static?
plat/st/stm32mp1/plat_image_load.c:29:13:
 warning: symbol 'plat_get_next_bl_params' was not declared.
 Should it be static?

plat/st/stm32mp1/bl2_io_storage.c:40:10:
 warning: symbol 'block_buffer' was not declared. Should it be static?
Signed-off-by: default avatarYann Gautier <yann.gautier@st.com>
      3e6fab43
    • Siva Durga Prasad Paladugu's avatar
      arm64: versal: Add support for new Xilinx Versal ACAPs · f91c3cb1
      Siva Durga Prasad Paladugu authored 
      

Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine Scalar
Processing Engines, Adaptable Hardware Engines, and Intelligent Engines with
leading-edge memory and interfacing technologies to deliver powerful
heterogeneous acceleration for any application. The Versal AI Core series has
five devices, offering 128 to 400 AI Engines. The series includes dual-core Arm
Cortex-A72 application processors, dual-core Arm Cortex-R5 real-time
processors, 256KB of on-chip memory with ECC, more than 1,900 DSP engines
optimized for high-precision floating point with low latency.

This patch adds Virtual QEMU platform support for
this SoC "versal_virt".
Signed-off-by: default avatarSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: default avatarMichal Simek <michal.simek@xilinx.com>
      f91c3cb1
  5. 08 Nov, 2018 4 commits
  7. 06 Nov, 2018 3 commits
  9. 05 Nov, 2018 1 commit
  11. 01 Nov, 2018 4 commits
  13. 31 Oct, 2018 2 commits
  15. 30 Oct, 2018 5 commits
  17. 29 Oct, 2018 5 commits
    • Antonio Nino Diaz's avatar
      plat/arm: Fix MISRA defects in SiP SVC handler · 15b94cc1
      Antonio Nino Diaz authored 
      

No functional changes.

Change-Id: I9b9f8d3dfde08d57706ad5450de6ff858a55ac01
Signed-off-by: default avatarAntonio Nino Diaz <antonio.ninodiaz@arm.com>
      15b94cc1
    • Deepak Pandey's avatar
      plat/arm: Introduce the N1SDP. · 80d37c28
      Deepak Pandey authored 
      

This patch adds support for the N1SDP (NeoVerse N1 System Development
Platform). It is an initial port and additional features are expected
to be added later.

The port includes only BL31 support as the System Control Processor
(SCP) is expected to take the role of primary boatloader

Change-Id: Ife17d8215a7bfcc1420204a72205e7ef920d0c10
Signed-off-by: default avatarDeepak Pandey <Deepak.Pandey@arm.com>
      80d37c28
    • Soby Mathew's avatar
      FVP: Enable PIE for RESET_TO_BL31=1 · fc922ca8
      Soby Mathew authored 
      

This patch enabled PIE for FVP when RESET_TO_BL31=1. The references
to BL31_BASE are replaced by BL31_START as being a symbol exported by
the linker, will create a dynamic relocation entry in .rela.dyn and
hence will be fixed up by dynamic linker at runtime. Also, we disable
RECLAIM_INIT_CODE when PIE is enabled as the init section overlay
creates some static relocations which cannot be handled by the
dynamic linker currently.

Change-Id: I86df1b0a8b2a8bbbe7c3f3c0b9a08c86c2963ec0
Signed-off-by: default avatarSoby Mathew <soby.mathew@arm.com>
      fc922ca8
    • Soby Mathew's avatar
      plat/arm: Use `mov_imm` macro to load immediate values · bd83b396
      Soby Mathew authored 
      

This patch makes use of mov_imm macro where possible to load
immediate values within ARM platform layer.

Change-Id: I02bc7fbc1fa334c9fccf76fbddf515952f9a1298
Signed-off-by: default avatarSoby Mathew <soby.mathew@arm.com>
      bd83b396
    • Soby Mathew's avatar
      Add helper to return reference to a symbol · 6a7b3005
      Soby Mathew authored 
      

This patch adds a utility function to return
the address of a symbol. By default, the compiler
generates adr/adrp instruction pair to return
the reference and this utility is used to override
this compiler generated to code and use `ldr`
instruction.

This is needed for Position Independent Executable
when it needs to reference a symbol which is constant
and does not depend on the execute address of the
binary.

For example, on the FVP, the GICv3 register context is
stored in a secure carveout (arm_el3_tzc_dram) within
DDR and does not relocate with the BL image. Now if
BL31 is executing at a different address other than
the compiled address, using adrp/adr instructions to
reference this memory will not work as they generate an
address that is PC relative. The way to get around this
problem is to reference it as non-PC relative (i.e
non-relocatable location) via `ldr` instruction.

Change-Id: I5008a951b007144258121690afb68dc8e12ee6f7
Signed-off-by: default avatarSoby Mathew <soby.mathew@arm.com>
      6a7b3005
  19. 26 Oct, 2018 8 commits
  21. 25 Oct, 2018 3 commits