GitLab

Add new flags for storage support that must be used in the build
command line. Add the complete build steps for an OP-TEE configuration.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I0c682f6eb0aab83aa929f4ba734d3151c264aeed

Remove second flash node as only one must be used
by QSPI NOR driver.

Change-Id: I48189f2fdf4e0455aabe7d4cd9b2f3d36bb9cfb5
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

STM32MP1 platform is able to boot from SPI-NOR devices.
These modifications add this support using the new
SPI-NOR framework.

Change-Id: I75ff9eba4661f9fb87ce24ced2bacbf8558ebe44
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

STM32MP1 platform is able to boot from SPI-NAND devices.
These modifications add this support using the new
SPI-NAND framework.

Change-Id: I0d5448bdc4bde153c1209e8043846c0f935ae5ba
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Add QSPI support (limited to read interface).
Implements the memory map and indirect modes.
Low level driver based on SPI-MEM operations.

Change-Id: Ied698e6de3c17d977f8b497c81f2e4a0a27c0961
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

Include the required FMC2 pinmux definition for the
NAND management.

Change-Id: I80333deacdf3444b2f21f17f2fb5919e569a3591
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

STM32MP1 platform is able to boot from raw NAND devices.
These modifications add this support using the new
raw NAND framework.

Change-Id: I9e9c2b03930f98a5ac23f2b6b41945bef43e5043
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Add fmc2_nand driver support. The driver implements
only read interface for NAND devices.

Change-Id: I3cd037e8ff645ce0d217092b96f33ef41cb7a522
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

For STM32MP1, the address space is 4GB, which can be first divided
in 4 parts of 1GB. This LVL1 table is already mapped regardless
of MAX_XLAT_TABLES.
Fixing typo: Replace Ko to KB.

BL2/sp_min for platform STM32MP1 requires 4 MMU translation tables:
  - a level2 table and a level3 table for identity mapped SYSRAM
  - a level2 table mapping 2MB of BootROM runtime resources
  - a level2 table mapping 2MB of secure DDR (case BL32 is OP-TEE)

Change-Id: If80cbd4fccc7689b39dd540d6649b1313557f326
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Device size could be more than 4GB, we must
define size as unsigned long long.

Change-Id: I52055cf5c1c15ff18ab9e157aa9b73c8b4fb7b63
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Add a new entry to find register properties by name and
include new assert functions to limit address cells to 1
and size cells to 1.

Change-Id: Ide59a795a05fb2af36bd07fec15e5a3adf196226
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Adds compilation flags to specify which drivers will be
embedded in the generated firmware.

Change-Id: Ie9decc89c3f26cf17e7148a3a4cf337fd35940f7
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Add the standard CLAMP macro.  It ensures that
x is between the limits set by low and high.
If low is greater than high the result is undefined.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Ia173bb9ca51bc8d9a8ec573bbc15636a94f881f4

Imported from the LLVM compiler_rt library on master branch as of
30 Oct 2018 (SVN revision: r345645).

This is to get the __popcountsi2(si_int a) and __popcountdi2(di_int a)
builtin which are required by a driver that uses a __builtin_popcount().

Change-Id: I8e0d97cebdd90d224690c8ce1b02e657acdddb25
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

SPI-NOR framework is based on SPI-MEM framework using
spi_mem_op execution interface.

It implements read functions and allows NOR configuration
up to quad mode.
Default management is 1 data line but it can be overridden
by platform.
It also includes specific quad mode configuration for
Spansion, Micron and Macronix memories.

Change-Id: If49502b899b4a75f6ebc3190f6bde1013651197f
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

This framework supports SPI-NAND and is based on the
SPI-MEM framework for SPI operations. It uses a common high
level access using the io_mtd.

It is limited to the read functionalities.

Default behavior is the basic one data line operation
but it could be overridden by platform.

Change-Id: Icb4e0887c4003a826f47c876479dd004a323a32b
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

This framework supports SPI operations using a common
spi_mem_op structure:
 - command
 - addr
 - dummy
 - data

The framework manages SPI bus configuration:
 - speed
 - bus width (Up to quad mode)
 - chip select

Change-Id: Idc2736c59bfc5ac6e55429eba5d385275ea3fbde
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

The raw NAND framework supports SLC NAND devices.

It introduces a new high level interface (io_mtd) that
defines operations a driver can register to the NAND framework.
This interface will fill in the io_mtd device specification:
	- device_size
        - erase_size
that could be used by the io_storage interface.

NAND core source file integrates the standard read loop that
performs NAND device read operations using a skip bad block strategy.
A platform buffer must be defined in case of unaligned
data. This buffer must fit to the maximum device page size
defined by PLATFORM_MTD_MAX_PAGE_SIZE.

The raw_nand.c source file embeds the specific NAND operations
to read data.
The read command is a raw page read without any ECC correction.
This can be overridden by a low level driver.
No generic support for write or erase command or software
ECC correction.

NAND ONFI detection is available and can be enabled using
NAND_ONFI_DETECT=1.
For non-ONFI NAND management, platform can define required
information.

Change-Id: Id80e9864456cf47f02b74938cf25d99261da8e82
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

* changes:
  io: change seek offset to signed long long
  compiler_rt: Import aeabi_ldivmode.S file and dependencies

* changes:
  zynqmp: pm: clock: Move custom flags to typeflags
  zynqmp: pm: clock: Add support for custom type flags
  plat: xilinx: zynqmp: Add GET_CALLBACK_DATA function
  zynqmp: pm: Remove CLK_TOPSW_LSBUS from invalid clock list

UEFI decompression will fail if the payload size is too large and the load
address is too low. This patch moves the payload to a higher address to fix
the issue
Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>
Change-Id: I36087fbd2237b62891c59dbe2d34336bddfaa396

All function in socfpga_sip_svc.c should only be called locally except
sip_smc_handler().
Signed-off-by: Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: Ib84ef9a2e521967baa4cfd32e6bc569dd3a5d2f5

Now that there is plenty of space (32 KiB) available for NOBITS
sections, we can afford using an entire page for coherent memory. In
fact, because it simplifies the code, this is a beneficial change for
loaded image (.text) size, where we are still close to the size limit.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I0b899dabcb162015c63b0e4aed0869569c889ed9

Implements a way to add platform specific power off code to a
Marvell Armada 8K platform.

Marvell Armada 8K boards can now add a board/system_power.c file
that contains a system_power_off() function.
This function can now send a command to a power management MCU or
other board periferals before shutting the board down.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Change-Id: Iaba20bc2f603195679c54ad12c0c18962dd8e3db
---
I am working on a device that will be ported later, which has a
custom power management MCU that handles LEDs, board power and fans
and requires this separation.

Add missing #address-cells and #size-cells into generated DT, otherwise
the DT is invalid. While the parsers thus far handled this correctly via
various fallbacks, this is not applicable in the long run, so fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Ic808a3b27b93e5258ec1a19acc3d593e53625c15

Existing implementation does not allow to change the value of the
DIV1 because DIV2 does not have SET_RATE_PARENT flag.
This causes DIV1 value to be fixed and only value of DIV2 will be
adjusted according to required clock rate.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: Ic6c4ca091bf0c5dc91ebddf86621c82c705dc87b

Linux expects custom flags in type flags. So move
custom flags to type flags instead of providing
them to clock core flags.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: I668a8084d966815a9d9e86c2b18ecb5b18cb6b78

Add support to add extra custom type flags and provide
to caller in topology query.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: Id9cc065dbadfed2291dd4f62674d7838da4cdf40

Add GET_CALLBACK_DATA function again as now Linux driver
supports both mailbox as well as ISR method.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: Ieb99d61976e1cb718fcd1021d9cf4958e7556c81

* changes:
  intel: Implement platform specific system reset 2
  intel: Enable SiP SMC secure register access

Merge "uniphier: call uniphier_scp_is_running() only when on-chip STM is supported" into integration