GitLab

This patch describes the boot-flow and building of the WaRP7 TF-A port.
What it describes is booting and unsigned TF-A.

A very brief section has been added on signing BL2 which is in no-way
comprehensive. For a comprehensive description of the signing process try
the Boundary Devices blog on the matter.

https://boundarydevices.com/high-assurance-boot-hab-dummies/

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Signed-off-by: Yann Gautier <yann.gautier@st.com>

The Non-secure DRAM region shouldn't be protected in the range specified
in the Linux command line with memmap.

This change also increases the size of the Secure DRAM region.

Change-Id: I306e9e443a84b834c99739f54a534a3ca3be2424
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

In the memory map of the documentation the kernel only had 16MiB of
allocated space. This leaves very little room for growth, so the
addresses of the DTB and the kernel have been interchanged.

The documentation has been updated to reflect this change.

Change-Id: Ib6eab69f047fa88561fb755397ce3a0b356c8860
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Add information about direct Linux kernel boot for kernels that support
PSCI.

Change-Id: I05f76aa36398edabf411cb25a646437af1862e6e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

It uses the hardware RNG in a similar way as Juno (it gets 128 bits of
entropy and does xor on them).

It is disabled by default.

Change-Id: I8b3adb61f5a5623716e0e8b6799404c68dd94c60
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

There is no way to boot BL31 at the addresses specified in the platform
memory map unless an extra loader is used at address 0x00000000. It is
better to remove it to prevent confusion. Having it enabled was a bug.

Change-Id: I3229fbc080f5996cff47efce8e799bae94e0d5cb
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Add a new default makefile target to concatenate BL1 and the FIP and
generate armstub8.bin. This way it isn't needed to do it manually.

Documentation updated to reflect the changes.

Change-Id: Id5b5b1b7b9f87767db63fd01180ddfea855a7207
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Running optee_test failed because SEC_DRAM0_SIZE is too small. Previous
is 2 MB. We enlarge it to 11 MB for passing the test. Also we reduce
the NS_DRAM0_SIZE from 13MB to 4MB so that the whole section is still
fit in 16MB.

This commit also modified the document to reflect the changes we've
made in code.
Tested-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

Implement minimal interrupt routing functions. All interrupts are
treated as non-secure interrupts to be handled by the non-secure world.

Add note to the documentation about disabling FIQs qhen using OP-TEE
with Linux.

Change-Id: I937096542d973925e43ae946c5d0b306d0d95a94
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Add paragraph for how to enable Trusted Board Boot for rpi3
Tested-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>

For Trusted Board Boot we enlarge the BL1 size from 64k to 128k.
Tested-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

The H6 is Allwinner's most recent SoC. It shares most peripherals with the
other ARMv8 Allwinner SoCs (A64/H5), but has a completely different memory
map.

Introduce a separate platform target, which includes a different header
file to cater for the address differences. Also add the new build target
to the documentation.

The new ATF platform name is "sun50i_h6".
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Add two empty lines to denote the paragraphs properly and improve
readability.
Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch is an attempt to run Trusted OS (OP-TEE OS being one of them) along
side BL31 image.

ATF supports multiple SPD's that can take dispatcher name (opteed for OP-TEE OS)
as an input using the 'SPD=<dispatcher name>' option during bl31 build.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

This patch is an attempt to run Trusted OS (OP-TEE OS being one of them) along
side BL31 image.

ATF supports multiple SPD's that can take dispatcher name (opteed for OP-TEE OS)
as an input using the 'SPD=<dispatcher name>' option during bl31 build.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

Add Makefile and plaform definations file.
My thanks to Daniel Thompson and Ard Biesheuvel for the bits and pieces
I've taken from their earlier work regarding build and deploy steps for
Developerbox based on Synquacer SoCs. They deserve much of the credit
for this work although, since I assembled and tested things, any blame
is probably mine.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>

Create the baseline Makefile, platform definitions file and platform
specific assembly macros file. This includes first set of constants
for the platform including cache sizes and linker format and a stub for
BL31 and the basic memory layout

K3 SoC family of processors do not use require a BL1 or BL2 binary,
since such functions are provided by an system controller on the SoC.
This lowers the burden of ATF to purely managing the local ARM cores
themselves.
Signed-off-by: Benjamin Fair <b-fair@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>

Describe how to use BL32 build variable to load OP-TEE into FIP.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

NXP's i.MX8QM is an ARMv8 SoC with 2 clusters, 2 Cortex-A72
cores in one cluster and 4 Cortex-A53 in the other cluster,
and also has system controller (Cortex-M4) inside, documentation
can be found in below link:

https://www.nxp.com/products/processors-and-microcontrollers/


applications-processors/i.mx-applications-processors/i.mx-8-processors:IMX8-SERIES

This patch adds support for booting up SMP linux kernel (v4.9).
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

NXP's i.MX8QX is an ARMv8 SoC with 4 Cortex-A35 cores and
system controller (Cortex-M4) inside, documentation can
be found in below link:

https://www.nxp.com/products/processors-and-microcontrollers/


applications-processors/i.mx-applications-processors/i.mx-8-processors:IMX8-SERIES

This patch adds support for booting up SMP linux kernel (v4.9).
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>

The Allwinner A64 SoC is quite popular on single board computers.
It comes with four Cortex-A53 cores in a singe cluster and the usual
peripherals for set-top box/tablet SoC.

The ATF platform target is called "sun50i_a64".

[Andre: adapted to amended directory layout, removed unneeded definitions ]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The order of the arguments of memmap was swapped. The old command was
reserving 256 MiB from the 16 MiB barrier, it should be reserving only
16 MiB at the 256 MiB barrier.

It worked because the memory used by the Trusted Firmware was reserved
anyway.

Change-Id: I3fefcfc0105ecf05ba5606517bc3236f4eb24ceb
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduce TF-A support for NXP's ls1043a platform.
more details information of ls1043a chip and ls1043ardb board
can be found at docs/plat/ls1043a.rst.

Boot sequence on ls1043a is: bootrom loads bl1 firstly, then bl1
loads bl2, bl2 will load bl31, bl32 and bl33, bl31 will boot
bl32(tee os) and bl33(u-boot or uefi), bl33 boot Linux kernel.

Now TF-A on ls1043ardb platform has the following features in this patch:
	* Support boot from Nor flash.
	* TF-A can boot bl33 which runs in el2 of non-secure world.
	* TF-A boot OPTee OS.
	* Support PSCI
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Chenyin.Ha <Chenyin.Ha@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: jiaheng.fan <jiaheng.fan@nxp.com>
Signed-off-by: Wen He <wen.he_1@nxp.com>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.

The crash console doesn't use this API, it uses internally the core
functions of the 16550 console.

`bl31_plat_runtime_setup` is no longer needed. When this platform port
was introduced, that function used to disable the console. It was needed
to override that behaviour. The new behaviour is to switch to the
runtime console. The console is registered for all scopes (boot, crash
and runtime) in `rpi3_console_init` so it is not needed to override the
default behaviour anymore.

Update documentation.

Change-Id: If2ee8f91044216183b7ef142e5c05ad6220ae92f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Update Arm Trusted Firmware references in the upstream documents to
Trusted Firmware-A (TF-A). This is for consistency with and
disambiguation from Trusted Firmware-M (TF-M).

Also update other Arm trademarks, e.g. ARM->Arm, ARMv8->Armv8-A.

Change-Id: I8bb0e18af29c6744eeea2dc6c08f2c10b20ede22
Signed-off-by: Dan Handley <dan.handley@arm.com>
Signed-off-by: David Cunado <david.cunado@arm.com>

Since non-TF ROM is used in HiKey960 platform (Hisilicon Hi3660 SoC),
replace BL1 by BL2_EL3 in normal boot mode.

When flush images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Since non-TF ROM is used in HiKey platform (Hisilicon Hi6220 SoC),
replace BL1 by BL2_EL3 in normal boot mode.

When we recovery images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

The correct name of the manufacturer is LeMaker.
Signed-off-by: Andreas Färber <afaerber@suse.de>

UniPhier platform implements non-TF boot ROM.  Prior to the BL2-AT-EL3
support, BL1 (worked as a pseudo ROM) was needed just for ensuring BL2
is entered at EL1-S.  Now, this platform is able to avoid this waste.

Enable the BL2_AT_EL3 option, and remove BL1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Commit 6f625747

 ("Convert documentation to reStructuredText")
automatically converted all documents by a tool.  I see some parts
were converted in an ugly way (or, at least, it is not my intention).
Also, the footnote is apparently broken.

I checked this document by my eyes, and reformated it so that it looks
nicer both in plain text and reST form.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The document was being rendered incorrectly.

Change-Id: I6e243d17d7cb6247f91698bc195eb0f6efeb7d17
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Added design documentation and usage guide for the AArch64 port of the
Arm Trusted Firmware to the Raspberry Pi 3.

Change-Id: I1be60fbbd54c797b48a1bcebfb944d332616a0de
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Signed-off-by: Victor Chong <victor.chong@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>

The board features the Hi3798C V200 with an integrated quad-core
64-bit ARM Cortex A53 processor and high performance Mali T720 GPU,
making it capable of running any commercial set-top solution based on
Linux or Android. Its high performance specification also supports a
premium user experience with up to H.265 HEVC decoding of 4K video at
60 frames per second.

SOC  Hisilicon Hi3798CV200
CPU  Quad-core ARM Cortex-A53 64 bit
DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB
USB  Two USB 2.0 ports One USB 3.0 ports
CONSOLE  USB-micro port for console support
ETHERNET  1 GBe Ethernet
PCIE  One PCIe 2.0 interfaces
JTAG  8-Pin JTAG
EXPANSION INTERFACE  Linaro 96Boards Low Speed Expansion slot
DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor
WIFI  802.11AC 2*2 with Bluetooth
CONNECTORS  One connector for Smart Card One connector for TSI

The platform boot sequence is as follows:
    l-loader --> arm_trusted_firmware --> u-boot

Repositories:
 - https://github.com/Linaro/poplar-l-loader.git
 - https://github.com/Linaro/poplar-u-boot.git



U-Boot is also upstream in the project's master branch.

Make sure you are using the correct branch on each one of these
repositories. The definition of "correct" might change over time (at
this moment in time this would be the "latest" branch).

Build Line:
make CROSS_COMPILE=aarch64-linux-gnu-  all fip SPD=none DEBUG=1
PLAT=poplar BL33=/path/to/u-boot.bin
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>