GitLab

STM32MP1 SDMMC device voltage is 3.3V. We should then precise the 2 ranges
3.2 to 3.3V and 3.3 to 3.4V in ocr_voltage field.

Change-Id: I88e479f8f16bfe608a7808eace0df3fdec48deab
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Some bugs in MMC stack needs to be fixed:
- scr cannot be local as this will cause cache issue when invalidating
after the read DMA transfer is completed
- ACMD41 needs to send voltage information in initialization, otherwise the
command is a query, thus will not initialize the controller
- when checking device state, retry until the retries counter goes to zero
before failing
Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>

Configure the GPIO5 09 pin as input on the ULCB board by default,
since the pin is routed on the expansion connector and not connected
to anything by default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Add support for the M3W 3.0 SoC and synchronize the upstream ATF with
Renesas downstream ATF release v2.0.1.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Due to the shared Mbed TLS heap optimisation introduced in 6d01a463

,
common code files were depending on Mbed TLS specific headers. This
dependency is now removed by moving the default, unoptimised heap
implementation inside the Mbed TLS specific files.

Change-Id: I11ea3eb4474f0d9b6cb79a2afd73a51a4a9b8994
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

Fix some typos and clarify some sentences.

Change-Id: Id276d1ced9a991b4eddc5c47ad9a825e6b29ef74
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This commit improves the SDHost driver for RPi3 as following:
 * Unblock MMC_CMD(17). Using MMC_CMD(17) is more efficient on
   block reading.
 * In some low probability that SEND_OP_COND might results CRC7
   error. We can consider that the command runs correctly. We don't
   need to retry this command so removing the code for retry.
 * Using MMC_BUS_WIDTH_1 as MMC default value to improve the stability.
 * Increase the clock to 50Mhz in data mode to speed up the io.
 * Change the pull resistors configuration to gain more stability.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

STM32MP1 chip embeds a dual Cortex-A7 and a Cortex-M4.
The support for Cortex-M4 clocks is added when configuring the clock tree.
Some minimal security features to allow communications between A7 and M4
are also added.

Change-Id: I60417e244a476f60a2758f4969700b2684056665
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Cortex a5 doesnt support hardware division such as sdiv and udiv commands.
This commit adds a software division function in assembly as well as include
appropriate files for software divison.

The software division algorithm is a modified version obtained from:
http://www.keil.com/support/man/docs/armasm/armasm_dom1359731155623.htm



Change-Id: Ib405a330da5f1cea1e68e07e7b520edeef9e2652
Signed-off-by: Usama Arif <usama.arif@arm.com>

Remove useless private structure in function prototypes.
Add a reference counter on clocks.
Prepare for future secured/shared/non-secured clocks.

Change-Id: I3dbed81721da5ceff5e10b2c4155b1e340c036ee
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

This change makes the platform to panic in case of peripheral reset
resource malfunction.

Change-Id: I17eb9cb045b78a4e5142a8c33b744e84992d732a
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

PWR, RCC, DDRPHYC & DDRCTRL addresses can be retrieved from device tree.
Platform asserts the value read from the DT are the SoC addresses.

Change-Id: I43f0890b51918a30c87ac067d3780ab27a0f59de
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

Create a new file stm32mp_clkfunc.c to put functions that could be common
between several platforms.

Change-Id: Ica915c796b162b2345056b33328acc05035a242c
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Regulator configuration at boot takes more information from DT.
I2C configuration from DT is done in I2C driver.
I2C driver manages more transfer modes.
The min voltage of buck1 should also be increased to 1.2V,
else the platform does not boot.

Heavily modifies stm32_i2c.c since many functions move inside the source
file to remove redundant declarations.

Change-Id: I0bee5d776cf3ff15e687427cd6abc06ab237d025
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

Remove the previously use function: get_timer, and use new functions
timeout_init_us and timeout_elapsed.

Change-Id: I4e95b123648bff7ca91e40462a2a3ae24cfe1697
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

Include all RCC, clocks and reset headers from stm32mp1_def.h
which if exported to the firmware through platform_def.h.
The same dependency removal is done in common code as well.
Some useless includes are also removed in stm32_sdmmc2 driver.

Change-Id: I731ea5775c3fdb7f7b0c388b93923ed5e84b8d3f
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Mainly remove suffix 1 from prefix stm32mp1 in several macros and functions
that can be used in drivers shared by different platforms.

Change-Id: I2295c44f5b1edac7e80a93c0e8dfd671b36e88e7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

Some parts of code could be shared with platform derivatives,
or new platforms.
A new folder plat/st/common is created to put common parts.

stm32mp_common.h is a common API aggregate.

Remove some casts where applicable.
Fix some types where applicable.
Remove also some platform includes that are already in stm32mp1_def.h.

Change-Id: I46d763c8d9e15732d1ee7383207fd58206d7f583
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

This is to add simple MBR partition entry support. This will read all four
MBR partition into the partition list, and the partition type will be saved
in the list.name[0] entry.
Signed-off-by: Loh Tien Hock <tien.hock.loh@intel.com>

This commit migrates to MULTI_CONSOLE_API for IMX Warp7 board.
We also rename the functions in imx_uart driver to more specific one.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

The Generic Timer is an optional extension to an ARMv7-A implementation.
The generic delay timer can be used from any architecture supported by
the Trusted Firmware. In ARMv7 it is needed to check that this feature
is present. In ARMv8 it is always present.

Change-Id: Ib7e8ec13ffbb2f64445d4ee48ed00f26e34b79b7
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Previously the GICv3 redistributor probe function
(gicv3_rdistif_base_addrs_probe()) asserted that the number of
per-CPU redistributor interfaces expected to be probed by the
platform is equal to the number exported by the redistributor
frame. This is a problem in case the number of CPUs in the
platform is less than the number of redistributor interfaces
in the frame. Hence this patch removes the assertion check
and allows probe for fewer redistributor interfaces as required
by the platform.

Change-Id: I3449763a3ad70817224442cbe184d001030c9874
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This commit adds SDHost driver for RaspberryPi3. SDHost driver uses the
GPIO driver to connect the SDCard and SDHost. By using this driver it is
able to read/write raw blocks on SDCard.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

Clean up the NOTICE() and FATAL_MSG() outputs, so that they contain
proper newlines and BL2 prefixes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Method cpld_reset_cpu of bl31 is called from the Linux kernel and uses
GPIO6, GPIO2 pins as SPI bus lines to control the CPLD device. But in the
kernel GPIO6_8 pin are initialized to work in interrupt mode instead of
the input/output mode. This leads to the fact that the SPI bus becomes
non-functional. In this patch we switch the GPIO6_8 pin back to the
input-output mode.
Signed-off-by: Sergii Boryshchenko <sergii.boryshchenko@globallogic.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

The ATF code fails to build with PMIC_ROHM_BD9571=0, add the missing
function into the PWRC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>

Change-Id: I2d67bb1bebd15e6a7d69ea5e7b6fda9c972f9d86
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>

This commit adds GPIO driver for RaspberryPi3. The GPIO driver for RPi3
also provides the way to do pinmux selections.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

Change-Id: I670ea80e0331c2d4b2ccfa563a45469a43f6902d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ia601d5ad65ab199e747fb60af4979b7db477d249
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ida5dae39478654405d0ee31a6cbddb4579e76a7f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Icc59cdaf2b56f6936e9847f1894594c671db2e94
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I656753a1825ea7340a3708b950fa6b57455e9056
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I8989d2aa0258bf3b50a856c5b81532d578600124
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The BSEC (Boot and Security and OTP control) is intended to control an OTP
(one time programmable) fuse box, used for on-chip non-volatile storage
for device configuration and security parameters.

Change-Id: I38c44684c7b9c6a1f24ec0ae3fe99cec481d5a51
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

Change fdt_check_status function to fdt_get_status.
Update GPIO defines.
Move some functions in gpio driver, instead of dt helper file.
Add GPIO bank helper functions.
Use only one status field in dt_node_info structure including both status
and secure status.

Change-Id: I34f93408dd4aac16ae722f564bc3f7d6ae978cf4
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

Reword some traces.
Use uintptr_t where required.
Reduce scope of variables.
Improve io_stm32image algo.
Complete some IP registers definitions.
Add failure on supported DDR (stm32mp1_ddr_init()).
Fix cache flush on cache disable (stm32mp1_ddr_setup).

Change-Id: Ie02fa71e02b9d69abc807fd5b7df233e5be6668c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

Change-Id: I4a1b281925e0a3a1e2a34b3e363537e4a7f13823
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

The drivers are also updated to reflect the changes.
Set RCC as non-secure.

Change-Id: I568fa1f418355830ad1d4d1cdcdb910fb362231b
Signed-off-by: Yann Gautier <yann.gautier@st.com>