GitLab

This patch adds a driver for ARM GICv2 systems, example GIC-400. Unlike
the existing GIC driver in `include/drivers/arm/arm_gic.h`, this driver
is optimised for GICv2 and does not support GICv3 systems in GICv2
compatibility mode. The driver interface has been implemented in
`drivers/arm/gic/v2/gicv2_main.c`. The corresponding header is in
`include/drivers/arm/gicv2.h`. Helper functions are implemented in
`drivers/arm/gic/v2/gicv2_helpers.c` and are accessible through the
`drivers/arm/gic/v2/gicv2_private.h` header.

Change-Id: I09fffa4e621fb99ba3c01204839894816cd89a2a

This patch adds a driver for ARM GICv3 systems that need to run software
stacks where affinity routing is enabled across all privileged exception
levels for both security states. This driver is a partial implementation
of the ARM Generic Interrupt Controller Architecture Specification, GIC
architecture version 3.0 and version 4.0 (ARM IHI 0069A). The driver does
not cater for legacy support of interrupts and asymmetric configurations.

The existing GIC driver has been preserved unchanged. The common code for
GICv2 and GICv3 systems has been refactored into a new file,
`drivers/arm/gic/common/gic_common.c`. The corresponding header is in
`include/drivers/arm/gic_common.h`.

The driver interface is implemented in `drivers/arm/gic/v3/gicv3_main.c`.
The corresponding header is in `include/drivers/arm/gicv3.h`. Helper
functions are implemented in `drivers/arm/gic/v3/arm_gicv3_helpers.c`
and are accessible through the `drivers/arm/gic/v3/gicv3_private.h`
header.

Change-Id: I8c3c834a1d049d05b776b4dcb76b18ccb927444a

From Linux 3.17 onwards, the mainline kernel has support for GICv3
systems and if EL3 exists, it only needs to initialise ICC_SRE_EL3.SRE
and ICC_SRE_EL3.Enable to 1. Hence, this patch removes the redundant
updates of ICC_SRE_EL2 and ICC_PMR_EL1.

NOTE: For partner software's which enter kernel in EL1,
ICC_SRE_EL2.Enable and ICC_SRE_EL2.SRE bit needs to be set to 1
in EL2 before jumping to linux.

Change-Id: I09ed47869351b08a3b034735f532bc677eaa6917

This patch changes the type of the base address parameter in the
ARM device driver APIs to uintptr_t (GIC, CCI, TZC400, PL011). The
uintptr_t type allows coverage of the whole memory space and to
perform arithmetic operations on the addresses. ARM platform code
has also been updated to use uintptr_t as GIC base address in the
configuration.

Fixes ARM-software/tf-issues#214

Change-Id: I1b87daedadcc8b63e8f113477979675e07d788f1

The ARM GIC driver treats the entire contents of the GICC_HPPIR as the interrupt
ID instead of just bits[9:0]. This could result in an SGI being treated as a
Group 1 interrupt on a GICv2 system.

This patch introduces a mask to retrieve only the ID from a read of GICC_HPPIR,
GICC_IAR and similar registers. The value read from these registers is masked
with this constant prior to use as an interrupt ID.

Fixes ARM-software/tf-issues#306

Change-Id: Ie3885157de33b71df9781a41f6ef015a30c4608d

On a GICv2 system, the group status of PPIs and SGIs is set in the GICD_IGROUPR0
register. On a GICv3 system, if affinity routing is enabled for the non-secure
state, then the group status of PPIs and SGIs should be set in the GICR_IGROUPR0
register. ARM Trusted firmware sets the group status using the GICv2
sequence. On a GICv3 system, if the group status of an interrupt is set to Group
1 through a write to the GICD_IGROUPR0, then the GICR_IGROUPR0 is updated as
well.

The current sequence is incorrect since it first marks all PPIs and SGIs as
Group 1. It then clears the bits in GICD_IGROUPR0 corresponding to secure
interrupts to set their group status to Group 0. This operation is a no-op. It
leaves the secure generic timer interrupt (#29) used by the TSP marked as Group
1. This causes the interrupt to interfere with the execution of non-secure
software. Once an interrupt has been marked as Group 1, the GICR_IGROUPR0 should
be programmed to change its group status.

This patch rectifies this issue by setting the group status of only the
non-secure PPI and SGIs to Group 1 in the first place. GICD_IGROUPR0 resets to
0. So secure interrupts are marked as Group 0 by default.

Change-Id: I958b4b15f3e2b2444ce4c17764def36216498d00

This patch introduces several improvements to the ARM GIC driver:

* In function gicd_set_itargetsr(), target CPU is specified using
  the same bit mask detailed in the GICD_ITARGETSRn register instead
  of the CPU linear ID, removing the dependency between bit position
  and linear ID in the platform porting. The current CPU bit mask
  may be obtained by reading GICD_ITARGETSR0.

* PPIs and SGIs are initialized in arm_gic_pcpu_distif_setup().
  SPIs are initialized in arm_gic_distif_setup().

* By default, non secure interrupts are assigned the maximum
  priority allowed to a non secure interrupt (defined by
  GIC_HIGHEST_NS_PRIORITY).

* GICR base address is allowed to be NULL for GICv1 and GICv2.

Change-Id: Ie2837fe860d43b2282e582dfdb13c39c6186f232

Assert a valid security state using the macro sec_state_is_valid().
Replace assert() with panic() in those cases that might arise
because of runtime errors and not programming errors.
Replace panic() with assert() in those cases that might arise
because of programming errors.

Fixes ARM-software/tf-issues#96

Change-Id: I51e9ef0439fd5ff5e0edfef49050b69804bf14d5

Refactor the FVP gic code in plat/fvp/fvp_gic.c to be a generic ARM
GIC driver in drivers/arm/gic/arm_gic.c. Provide the platform
specific inputs in the arm_gic_setup() function so that the driver
has no explicit dependency on platform code.

Provide weak implementations of the platform interrupt controller
API in a new file, plat/common/plat_gic.c. These simply call through
to the ARM GIC driver.

Move the only remaining FVP GIC function, fvp_gic_init() to
plat/fvp/aarch64/fvp_common.c and remove plat/fvp/fvp_gic.c

Fixes ARM-software/tf-issues#182

Change-Id: Iea82fe095fad62dd33ba9efbddd48c57717edd21

Replace the current out-of-line assembler implementations of
the system register and system instruction operations with
inline assembler.

This enables better compiler optimisation and code generation
when accessing system registers.

Fixes ARM-software/tf-issues#91

Change-Id: I149af3a94e1e5e5140a3e44b9abfc37ba2324476

This patch introduces a framework for registering interrupts routed to
EL3. The interrupt routing model is governed by the SCR_EL3.IRQ and
FIQ bits and the security state an interrupt is generated in. The
framework recognizes three type of interrupts depending upon which
exception level and security state they should be handled in
i.e. Secure EL1 interrupts, Non-secure interrupts and EL3
interrupts. It provides an API and macros that allow a runtime service
to register an handler for a type of interrupt and specify the routing
model. The framework validates the routing model and uses the context
management framework to ensure that it is applied to the SCR_EL3 prior
to entry into the target security state. It saves the handler in
internal data structures. An API is provided to retrieve the handler
when an interrupt of a particular type is asserted. Registration is
expected to be done once by the primary CPU. The same handler and
routing model is used for all CPUs.

Support for EL3 interrupts will be added to the framework in the
future. A makefile flag has been added to allow the FVP port choose
between ARM GIC v2 and v3 support in EL3. The latter version is
currently unsupported.

A framework for handling interrupts in BL3-1 will be introduced in
subsequent patches. The default routing model in the absence of any
handlers expects no interrupts to be routed to EL3.

Change-Id: Idf7c023b34fcd4800a5980f2bef85e4b5c29e649

This patch fixes C accessors to GIC registers that follow a set/clear
semantic to change the state of an interrupt, instead of read/write/modify.
These registers are:
  Set-Enable
  Clear-Enable
  Set-Pending
  Clear-Pending
  Set-Active
  Clear-Active
For instance, to enable an interrupt we write a one to the corresponding bit
in the Set-Enable register, whereas to disable it we write a one to the
corresponding bit in the Clear-Enable register.

Fixes ARM-software/tf-issues#137

Change-Id: I3b66bad94d0b28e0fe08c9042bac0bf5ffa07944

The current code does not always use data and instruction
barriers as required by the architecture and frequently uses
barriers excessively due to their inclusion in all of the
write_*() helper functions.

Barriers should be used explicitly in assembler or C code
when modifying processor state that requires the barriers in
order to enable review of correctness of the code.

This patch removes the barriers from the helper functions and
introduces them as necessary elsewhere in the code.

PORTING NOTE: check any port of Trusted Firmware for use of
system register helper functions for reliance on the previous
barrier behaviour and add explicit barriers as necessary.

Fixes ARM-software/tf-issues#92

Change-Id: Ie63e187404ff10e0bdcb39292dd9066cb84c53bf

Reduce the number of header files included from other header
files as much as possible without splitting the files. Use forward
declarations where possible. This allows removal of some unnecessary
"#ifndef __ASSEMBLY__" statements.

Also, review the .c and .S files for which header files really need
including and reorder the #include statements alphabetically.

Fixes ARM-software/tf-issues#31

Change-Id: Iec92fb976334c77453e010b60bcf56f3be72bd3e

Move the function prototypes from gic.h into either gic_v2.h or
gic_v3.h as appropriate. Update the source files to include the
correct headers.

Change-Id: I368cfda175cdcbd3a68f46e2332738ec49048e19

Move almost all system include files to a logical sub-directory
under ./include. The only remaining system include directories
not under ./include are specific to the platform. Move the
corresponding source files to match the include directory
structure.

Also remove pm.h as it is no longer used.

Change-Id: Ie5ea6368ec5fad459f3e8a802ad129135527f0b3