GitLab

This patch adds a driver for ARM GICv2 systems, example GIC-400. Unlike
the existing GIC driver in `include/drivers/arm/arm_gic.h`, this driver
is optimised for GICv2 and does not support GICv3 systems in GICv2
compatibility mode. The driver interface has been implemented in
`drivers/arm/gic/v2/gicv2_main.c`. The corresponding header is in
`include/drivers/arm/gicv2.h`. Helper functions are implemented in
`drivers/arm/gic/v2/gicv2_helpers.c` and are accessible through the
`drivers/arm/gic/v2/gicv2_private.h` header.

Change-Id: I09fffa4e621fb99ba3c01204839894816cd89a2a

This patch adds a driver for ARM GICv3 systems that need to run software
stacks where affinity routing is enabled across all privileged exception
levels for both security states. This driver is a partial implementation
of the ARM Generic Interrupt Controller Architecture Specification, GIC
architecture version 3.0 and version 4.0 (ARM IHI 0069A). The driver does
not cater for legacy support of interrupts and asymmetric configurations.

The existing GIC driver has been preserved unchanged. The common code for
GICv2 and GICv3 systems has been refactored into a new file,
`drivers/arm/gic/common/gic_common.c`. The corresponding header is in
`include/drivers/arm/gic_common.h`.

The driver interface is implemented in `drivers/arm/gic/v3/gicv3_main.c`.
The corresponding header is in `include/drivers/arm/gicv3.h`. Helper
functions are implemented in `drivers/arm/gic/v3/arm_gicv3_helpers.c`
and are accessible through the `drivers/arm/gic/v3/gicv3_private.h`
header.

Change-Id: I8c3c834a1d049d05b776b4dcb76b18ccb927444a

Patch 7e26fe1f deprecates IO specific return definitions in favour
of standard errno codes. This patch removes those definitions
and its usage from the IO framework, IO drivers and IO platform
layer. Following this patch, standard errno codes must be used
when checking the return value of an IO function.

Change-Id: Id6e0e9d0a7daf15a81ec598cf74de83d5768650f

This patch fixes a copy and paste issue that resulted in the cluster
indexes not being checked as intended. Note that this fix applies to
the deprecated CCI-400 driver, not the unified one.

Change-Id: I497132a91c236690e5eaff908f2db5c8c65e85ab

This patch adds a device driver which can be used to program the following
aspects of ARM CCN IP:

1. Specify the mapping between ACE/ACELite/ACELite+DVM/CHI master interfaces and
   Request nodes.
2. Add and remove master interfaces from the snoop and dvm
   domains.
3. Place the L3 cache in a given power state.
4. Configuring system adress map and enabling 3 SN striping mode of memory
   controller operation.

Change-Id: I0f665c6a306938e5b66f6a92f8549b529aa8f325

From Linux 3.17 onwards, the mainline kernel has support for GICv3
systems and if EL3 exists, it only needs to initialise ICC_SRE_EL3.SRE
and ICC_SRE_EL3.Enable to 1. Hence, this patch removes the redundant
updates of ICC_SRE_EL2 and ICC_PMR_EL1.

NOTE: For partner software's which enter kernel in EL1,
ICC_SRE_EL2.Enable and ICC_SRE_EL2.SRE bit needs to be set to 1
in EL2 before jumping to linux.

Change-Id: I09ed47869351b08a3b034735f532bc677eaa6917

The return value from the SYS_WRITE semihosting operation is 0 if
the call is successful or the number of bytes not written, if there
is an error. The implementation of the write function in the
semihosting driver treats the return value as the number of bytes
written, which is wrong. This patch fixes it.

Change-Id: Id39dac3d17b5eac557408b8995abe90924c85b85

This patch changes the type of the base address parameter in the
ARM device driver APIs to uintptr_t (GIC, CCI, TZC400, PL011). The
uintptr_t type allows coverage of the whole memory space and to
perform arithmetic operations on the addresses. ARM platform code
has also been updated to use uintptr_t as GIC base address in the
configuration.

Fixes ARM-software/tf-issues#214

Change-Id: I1b87daedadcc8b63e8f113477979675e07d788f1

This patch adds a CoT based on the Trusted Board Boot Requirements
document*. The CoT consists of an array of authentication image
descriptors indexed by the image identifiers.

A new header file with TBBR image identifiers has been added.
Platforms that use the TBBR (i.e. ARM platforms) may reuse these
definitions as part of their platform porting.

PLATFORM PORT - IMPORTANT:

Default image IDs have been removed from the platform common
definitions file (common_def.h). As a consequence, platforms that
used those common definitons must now either include the IDs
provided by the TBBR header file or define their own IDs.

*The NVCounter authentication method has not been implemented yet.

Change-Id: I7c4d591863ef53bb0cd4ce6c52a60b06fa0102d5

This patch adds the following mbedTLS based libraries:

* Cryptographic library

It is used by the crypto module to verify a digital signature
and a hash. This library relies on mbedTLS to perform the
cryptographic operations. mbedTLS sources must be obtained
separately.

Two key algorithms are currently supported:

    * RSA-2048
    * ECDSA-SECP256R1

The platform is responsible for picking up the required
algorithm by defining the 'MBEDTLS_KEY_ALG' variable in the
platform makefile. Available options are:

    * 'rsa' (for RSA-2048) (default option)
    * 'ecdsa' (for ECDSA-SECP256R1)

Hash algorithm currently supported is SHA-256.

* Image parser library

Used by the image parser module to extract the authentication
parameters stored in X509v3 certificates.

Change-Id: I597c4be3d29287f2f18b82846973afc142ee0bf0

This patch adds the authentication framework that will be used as
the base to implement Trusted Board Boot in the Trusted Firmware.
The framework comprises the following modules:

- Image Parser Module (IPM)

    This module is responsible for interpreting images, check
    their integrity and extract authentication information from
    them during Trusted Board Boot.

    The module currently supports three types of images i.e.
    raw binaries, X509v3 certificates and any type specific to
    a platform. An image parser library must be registered for
    each image type (the only exception is the raw image parser,
    which is included in the main module by default).

    Each parser library (if used) must export a structure in a
    specific linker section which contains function pointers to:

        1. Initialize the library
        2. Check the integrity of the image type supported by
           the library
        3. Extract authentication information from the image

- Cryptographic Module (CM)

    This module is responsible for verifying digital signatures
    and hashes. It relies on an external cryptographic library
    to perform the cryptographic operations.

    To register a cryptographic library, the library must use the
    REGISTER_CRYPTO_LIB macro, passing function pointers to:

        1. Initialize the library
        2. Verify a digital signature
        3. Verify a hash

    Failing to register a cryptographic library will generate
    a build time error.

- Authentication Module (AM)

    This module provides methods to authenticate an image, like
    hash comparison or digital signatures. It uses the image parser
    module to extract authentication parameters, the crypto module
    to perform cryptographic operations and the Chain of Trust to
    authenticate the images.

    The Chain of Trust (CoT) is a data structure that defines the
    dependencies between images and the authentication methods
    that must be followed to authenticate an image.

The Chain of Trust, when added, must provide a header file named
cot_def.h with the following definitions:

- COT_MAX_VERIFIED_PARAMS

    Integer value indicating the maximum number of authentication
    parameters an image can present. This value will be used by the
    authentication module to allocate the memory required to load
    the parameters in the image descriptor.

Change-Id: Ied11bd5cd410e1df8767a1df23bb720ce7e58178

The Trusted firmware code identifies BL images by name. The platform
port defines a name for each image e.g. the IO framework uses this
mechanism in the platform function plat_get_image_source(). For
a given image name, it returns the handle to the image file which
involves comparing images names. In addition, if the image is
packaged in a FIP, a name comparison is required to find the UUID
for the image. This method is not optimal.

This patch changes the interface between the generic and platform
code with regard to identifying images. The platform port must now
allocate a unique number (ID) for every image. The generic code will
use the image ID instead of the name to access its attributes.

As a result, the plat_get_image_source() function now takes an image
ID as an input parameter. The organisation of data structures within
the IO framework has been rationalised to use an image ID as an index
into an array which contains attributes of the image such as UUID and
name. This prevents the name comparisons.

A new type 'io_uuid_spec_t' has been introduced in the IO framework
to specify images identified by UUID (i.e. when the image is contained
in a FIP file). There is no longer need to maintain a look-up table
[iname_name --> uuid] in the io_fip driver code.

Because image names are no longer mandatory in the platform port, the
debug messages in the generic code will show the image identifier
instead of the file name. The platforms that support semihosting to
load images (i.e. FVP) must provide the file names as definitions
private to the platform.

The ARM platform ports and documentation have been updated accordingly.
All ARM platforms reuse the image IDs defined in the platform common
code. These IDs will be used to access other attributes of an image in
subsequent patches.

IMPORTANT: applying this patch breaks compatibility for platforms that
use TF BL1 or BL2 images or the image loading code. The platform port
must be updated to match the new interface.

Change-Id: I9c1b04cb1a0684c6ee65dee66146dd6731751ea5

Add a delay timer driver for the ARM SP804 dual timer.

This driver only uses the first timer, called timer 1 in the
SP804 Technical Reference Manual (ARM DDI 0271D).

To use this driver, the BSP must provide three constants:

*   The base address of the SP804 dual timer
*   The clock multiplier
*   The clock divider

The BSP is responsible for calling sp804_timer_init(). The SP804
driver instantiates a constant timer_ops_t and calls the generic
timer_init().

Change-Id: I49ba0a52bdf6072f403d1d0a20e305151d4bc086
Co-authored-by: Dan Handley <dan.handley@arm.com>

The API is simple. The BSP or specific timer driver creates an
instance of timer_ops_t, fills in the timer specific data, then calls
timer_init(). The timer specific data includes a function pointer
to return the timer value and a clock multiplier/divider. The ratio
of the multiplier and the divider is the clock frequency in MHz.

After that, mdelay() or udelay() can be called to delay execution for
the specified time (milliseconds or microseconds, respectively).

Change-Id: Icf8a295e1d25874f789bf28b7412156329dc975c
Co-authored-by: Dan Handley <dan.handley@arm.com>

This patch adds driver for the 16550 UART interface. The driver is exposed
as a console, which platforms can use to dump their boot/crash logs.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The ARM GIC driver treats the entire contents of the GICC_HPPIR as the interrupt
ID instead of just bits[9:0]. This could result in an SGI being treated as a
Group 1 interrupt on a GICv2 system.

This patch introduces a mask to retrieve only the ID from a read of GICC_HPPIR,
GICC_IAR and similar registers. The value read from these registers is masked
with this constant prior to use as an interrupt ID.

Fixes ARM-software/tf-issues#306

Change-Id: Ie3885157de33b71df9781a41f6ef015a30c4608d

Separate out the common console functionality in
`drivers/arm/pl011/pl011_console.S` into a new source file
`drivers/console/console.S`. The former includes the latter to
provide backwards compatibility for platform make files.

Also add a skeleton console implementation for platforms that do not
want to use PL011.

Change-Id: I1ff963b2b54a872fbcf1eb0700797b9e9afa2538

Region 0 is special in TZC-400. It is possible to set the access
permissions for this but not the address range or filters to which
the permissions apply. Add a function for setting the region 0
access permissions.

Also add some VERBOSE logging and allow assembly files to include
the TZC header.

Change-Id: I4389261ba10a6e5e2e43ee93d55318dc507b6648

In order for the symbol table in the ELF file to contain the size of
functions written in assembly, it is necessary to report it to the
assembler using the .size directive.

To fulfil the above requirements, this patch introduces an 'endfunc'
macro which contains the .endfunc and .size directives. It also adds
a .func directive to the 'func' assembler macro.

The .func/.endfunc have been used so the assembler can fail if
endfunc is omitted.

Fixes ARM-Software/tf-issues#295

Change-Id: If8cb331b03d7f38fe7e3694d4de26f1075b278fc
Signed-off-by: Kévin Petit <kevin.petit@arm.com>

On a GICv2 system, the group status of PPIs and SGIs is set in the GICD_IGROUPR0
register. On a GICv3 system, if affinity routing is enabled for the non-secure
state, then the group status of PPIs and SGIs should be set in the GICR_IGROUPR0
register. ARM Trusted firmware sets the group status using the GICv2
sequence. On a GICv3 system, if the group status of an interrupt is set to Group
1 through a write to the GICD_IGROUPR0, then the GICR_IGROUPR0 is updated as
well.

The current sequence is incorrect since it first marks all PPIs and SGIs as
Group 1. It then clears the bits in GICD_IGROUPR0 corresponding to secure
interrupts to set their group status to Group 0. This operation is a no-op. It
leaves the secure generic timer interrupt (#29) used by the TSP marked as Group
1. This causes the interrupt to interfere with the execution of non-secure
software. Once an interrupt has been marked as Group 1, the GICR_IGROUPR0 should
be programmed to change its group status.

This patch rectifies this issue by setting the group status of only the
non-secure PPI and SGIs to Group 1 in the first place. GICD_IGROUPR0 resets to
0. So secure interrupts are marked as Group 0 by default.

Change-Id: I958b4b15f3e2b2444ce4c17764def36216498d00

Even though both CCI-400 and CCI-500 IPs have different configurations
with respect to the number and types of supported interfaces, their
register offsets and programming sequences are similar. This patch
creates a common driver for enabling and disabling snoop transactions
and DVMs with both the IPs.

New platform ports which implement one of these IPs should use this
common driver. Existing platform ports which implement CCI-400 should
migrate to the common driver as the standalone CCI-400 will be
deprecated in the future.

Change-Id: I3ccd0eb7b062922d2e4a374ff8c21e79fa357556

This patch defines the ARRAY_SIZE macro for calculating number of elements
in an array and uses it where appropriate.

Change-Id: I72746a9229f0b259323972b498b9a3999731bc9b

This patch adds support to authenticate the Trusted Key certificate
and the BL3-x certificates and images at BL2.

Change-Id: I69a8c13a14c8da8b75f93097d3a4576aed71c5dd

This patch adds support to authenticate the BL2 content certificate
and image using the authentication module in BL1.

The FIP driver has been extended to include the BL2 certificate
UUID.

FVP and Juno ports include the BL2 certificate FIP file
definition.

Change-Id: I32680e9bd123c8db4a4193c14448c9b32b0e9325

This patch introduces several improvements to the ARM GIC driver:

* In function gicd_set_itargetsr(), target CPU is specified using
  the same bit mask detailed in the GICD_ITARGETSRn register instead
  of the CPU linear ID, removing the dependency between bit position
  and linear ID in the platform porting. The current CPU bit mask
  may be obtained by reading GICD_ITARGETSR0.

* PPIs and SGIs are initialized in arm_gic_pcpu_distif_setup().
  SPIs are initialized in arm_gic_distif_setup().

* By default, non secure interrupts are assigned the maximum
  priority allowed to a non secure interrupt (defined by
  GIC_HIGHEST_NS_PRIORITY).

* GICR base address is allowed to be NULL for GICv1 and GICv2.

Change-Id: Ie2837fe860d43b2282e582dfdb13c39c6186f232

This patch configures the TrustZone Controller in Juno to split
the 2GB DDR-DRAM memory at 0x80000000 into Secure and Non-Secure
regions:

- Secure DDR-DRAM: top 16 MB, except for the last 2 MB which are
  used by the SCP for DDR retraining
- Non-Secure DDR-DRAM: remaining DRAM starting at base address

Build option PLAT_TSP_LOCATION selects the location of the secure
payload (BL3-2):

- 'tsram' : Trusted SRAM (default option)
- 'dram'  : Secure region in the DDR-DRAM (set by the TrustZone
            controller)

The MMU memory map has been updated to give BL2 permission to load
BL3-2 into the DDR-DRAM secure region.

Fixes ARM-software/tf-issues#233

Change-Id: I6843fc32ef90aadd3ea6ac4c7f314f8ecbd5d07b

The TZC-400 driver previously allowed the possibility of multiple
controller instances to be present in the same executable. This
was unnecessary since there will only ever be one instance.

This change simplifies the tzc_init() function to only take the
base address argument needed by implementation, conforming to the
driver initialization model of other drivers. It also hides some
of the implementation details that were previously exposed by the
API.

The FVP port has been updated accordingly.

THIS CHANGE REQUIRES ALL PLATFORM PORTS THAT USE THE TZC-400
DRIVER TO BE UPDATED

Fixes ARM-software/tf-issues#181

Change-Id: I7b721edf947064989958d8f457d6462d92e742c8

Move the remaining IO storage source file (io_storage.c) from the
lib to the drivers directory. This requires that platform ports
explicitly add this file to the list of source files.

Also move the IO header files to a new sub-directory, include/io.

Change-Id: I862b1252a796b3bcac0d93e50b11e7fb2ded93d6

* Create cci_init() function in CCI-400 driver to allow platform
  to provide arguments needed by the driver (i.e. base address
  and cluster indices for the ACE slave interfaces).

* Rename cci_(en|dis)able_coherency to
  cci_(en|dis)able_cluster_coherency to make it clear that
  the driver only enables/disables the coherency of CPU
  clusters and not other devices connected to the CCI-400.

* Update FVP port to use new cci_init() function and remove
  unnecessary CCI defintions from platform_def.h. Also rename
  fvp_cci_setup() to fvp_cci_enable() to more clearly
  differentiate between CCI initialization and enabling.

THIS CHANGE REQUIRES PLATFORM PORTS THAT USE THE CCI-400 DRIVER
TO BE UPDATED

Fixes ARM-software/tf-issues#168

Change-Id: I1946a51409b91217b92285b6375082619f607fec

Fix the following issues with the console log output:

* Make sure the welcome string is the first thing in the log output
(during normal boot).
* Prefix each message with the BL image name so it's clear which
BL the output is coming from.
* Ensure all output is wrapped in one of the log output macros so it can
be easily compiled out if necessary. Change some of the INFO() messages
to VERBOSE(), especially in the TSP.
* Create some extra NOTICE() and INFO() messages during cold boot.
* Remove all usage of \r in log output.

Fixes ARM-software/tf-issues#231

Change-Id: Ib24f7acb36ce64bbba549f204b9cde2dbb46c8a3

Assert a valid security state using the macro sec_state_is_valid().
Replace assert() with panic() in those cases that might arise
because of runtime errors and not programming errors.
Replace panic() with assert() in those cases that might arise
because of programming errors.

Fixes ARM-software/tf-issues#96

Change-Id: I51e9ef0439fd5ff5e0edfef49050b69804bf14d5

This patch adds baud rate and UART clock frequency as parameters
to the pl011 driver api console_init(). This allows each platform
to specify UART clock and baud rate according to their specific
hardware implementation.

Fixes ARM-software/tf-issues#215

Change-Id: Id13eef70a1c530e709b34dd1e6eb84db0797ced2

This patch replaces the pl011 console family of functions
with their equivalents defined in assembly. The baud rate is
defined by the PL011_BAUDRATE macro and IBRD and FBRD values
for pl011 are computed statically. This patch will enable
us to invoke the console functions without the C Runtime Stack.

Change-Id: Ic3f7b7370ded38bf9020bf746b362081b76642c7

 - Add support for loading a BL3-0 image in BL2. Information about
   memory extents is populated by platform-specific code. Subsequent
   handling of BL3-0 is also platform specific.
   The BL2 main function has been broken down to improve readability.
   The BL3-2 image is now loaded before the BL3-3 image to align with
   the boot flow.

 - Build system: Add support for specifying a BL3-0 image that will be
   included into the FIP image.

 - IO FIP driver: Add support for identifying a BL3-0 image inside a
   FIP image.

 - Update the documentation to reflect the above changes.

Change-Id: I067c184afd52ccaa86569f13664757570c86fc48

Refactor the FVP gic code in plat/fvp/fvp_gic.c to be a generic ARM
GIC driver in drivers/arm/gic/arm_gic.c. Provide the platform
specific inputs in the arm_gic_setup() function so that the driver
has no explicit dependency on platform code.

Provide weak implementations of the platform interrupt controller
API in a new file, plat/common/plat_gic.c. These simply call through
to the ARM GIC driver.

Move the only remaining FVP GIC function, fvp_gic_init() to
plat/fvp/aarch64/fvp_common.c and remove plat/fvp/fvp_gic.c

Fixes ARM-software/tf-issues#182

Change-Id: Iea82fe095fad62dd33ba9efbddd48c57717edd21

The assertion in console_putc() would trigger a recursion that
exhausts the stack and eventually aborts.

This patch replaces the assertion with an error return if the
console has not been initialized yet.

Fixes ARM-software/tf-issues#208

Change-Id: I95f736ff215d69655eb5ba7ceac70dc1409d986a

Replace the current out-of-line assembler implementations of
the system register and system instruction operations with
inline assembler.

This enables better compiler optimisation and code generation
when accessing system registers.

Fixes ARM-software/tf-issues#91

Change-Id: I149af3a94e1e5e5140a3e44b9abfc37ba2324476

Before attempting to write a character, the PL011 driver polls
the PL011_UARTFR_TXFF bit to know whether the UART FIFO is full.
However, the comparison with 1 was incorrect because
PL011_UARTFR_TXFF is not at bit 0. This patch fixes it.

Change-Id: If78892345bbdc8a5e4ae4a1b7159753c609681b0

Previously, platform.h contained many declarations and definitions
used for different purposes. This file has been split so that:

* Platform definitions used by common code that must be defined
  by the platform are now in platform_def.h. The exact include
  path is exported through $PLAT_INCLUDES in the platform makefile.

* Platform definitions specific to the FVP platform are now in
  /plat/fvp/fvp_def.h.

* Platform API declarations specific to the FVP platform are now
  in /plat/fvp/fvp_private.h.

* The remaining platform API declarations that must be ported by
  each platform are still in platform.h but this file has been
  moved to /include/plat/common since this can be shared by all
  platforms.

Change-Id: Ieb3bb22fbab3ee8027413c6b39a783534aee474a

The generic image loading and IO FIP code no longer forces the
platform to create BL3-2 (Secure-EL1 Payload) specific
definitions. The BL3-2 loading code in bl2/bl2main.c is wrapped
by a #ifdef BL32_BASE blocks, allowing the BL3-2 definitions to
be optional. Similarly for the name_uuid array defintion in
drivers/io/io_fip.c.

Also update the porting guide to reflect this change.

The BL3-2 platform definitions remain non-configurably present
in the FVP port.

Fixes ARM-software/tf-issues#68

Change-Id: Iea28b4e94d87a31f5522f271e290919a8a955460