GitLab

* changes:
  uniphier: make I/O register region configurable
  uniphier: make PSCI related base address configurable
  uniphier: make counter control base address configurable
  uniphier: make UART base address configurable
  uniphier: make pinmon base address configurable
  uniphier: make NAND controller base address configurable
  uniphier: make eMMC controller base address configurable

Adding support for generating a semi-random number required for
enabling building TF-A with stack protector support.
TF-A for corstone-700 may now be built using ENABLE_STACK_PROTECTOR=all

Change-Id: I03e1be1a8d4e4a822cf286f3b9ad4da4337ca765
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>

* changes:
  uniphier: extend boot device detection for future SoCs
  uniphier: change block_addressing flag to bool
  uniphier: change the return value type of .is_usb_boot() to bool

* changes:
  plat: marvell: armada: scp_bl2: allow loading up to 8 images
  plat: marvell: armada: add support for loading MG CM3 images

Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I8c2e6dc98f2f30a81f4f80cc0ca1232fed7a53c9

The I/O register region will be changed in the next SoC. Make it
configurable.

Change-Id: Iec0cbd1ef2d0703ebc7c3d3082edd73791bbfec9
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The next SoC will have:
  - No boot swap
  - SD boot
  - No USB boot

Add new fields to handle this.

Change-Id: I772395f2c5dfc612e575b0cbd0657a5fa9611c25
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The register base address will be changed in the next SoC. Make it
configurable.

Change-Id: Ibe07bd9db128b0f7e629916cb6ae21ba7984eca9
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The flag, uniphier_emmc_block_addressing, is boolean logic, so
"bool' is more suitable.

uniphier_emmc_is_over_2gb() is not boolean - it returns 1 / 0
depending on the card density, or a negative value on failure.
Rename it to make it less confusing.

Change-Id: Ia646b1929147b644e0df07c46b54ab80548bc3bd
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The register base will be changed in the next SoC. Make it
configurable.

Change-Id: I4a7cf85fe50e4d71db58a3372a71774e43193bd3
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This is boolean logic, so "bool" is more suitable.

Change-Id: I439c5099770600a65b8f58390a4c621c2ee487a5
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The next SoC supports the same UART, but the register base will be
changed. Make it configurable.

Change-Id: Ida5c9151b2f3554afd15555b22838437eef443f7
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The register base will be changed in the next SoC. Make it
configurable.

Change-Id: I9fbb6bdd1cf06207618742d4ad7970d911c9bc26
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The next SoC does not support the NAND controller, but make the base
address configurable for consistency and future proof.

Change-Id: I776e43ff2b0408577919b0b72849c3e1e5ce0758
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The next SoC supports the same eMMC controller, but the register
base will be changed. Make it configurable.

Change-Id: I00cb5531bc3d8d49357ad5e922cdd3d785355edf
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

* changes:
  arm-io: Panic in case of io setup failure
  MISRA fix: Use boolean essential type
  fconf: Add documentation
  fconf: Move platform io policies into fconf
  fconf: Add mbedtls shared heap as property
  fconf: Add TBBR disable_authentication property
  fconf: Add dynamic config DTBs info as property
  fconf: Populate properties from dtb during bl2 setup
  fconf: Load config dtb from bl1
  fconf: initial commit

Forced hash generation used to always generate hash via RSA encryption.
This patch changes encryption based on ARM_ROTPK_LOCATION.
Also removes setting KEY_ALG based on ARM_ROTPL_LOCATION - there is no
relation between these two.
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: Id727d2ed06176a243719fd0adfa0cae26c325005

* changes:
  SPMD: enable SPM dispatcher support
  SPMD: hook SPMD into standard services framework
  SPMD: add SPM dispatcher based upon SPCI Beta 0 spec
  SPMD: add support to run BL32 in TDRAM and BL31 in secure DRAM on Arm FVP
  SPMD: add support for an example SPM core manifest
  SPMD: add SPCI Beta 0 specification header file

* changes:
  amlogic: axg: Add a build flag when using ATOS as BL32
  amlogic: axg: Add support for the A113D (AXG) platform

This patch adds support to the build system to include support for the SPM
dispatcher when the SPD configuration option is spmd.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: Ic1ae50ecd7403fcbcf1d318abdbd6ebdc642f732

This patch adds support to initialise the SPM dispatcher as a standard
secure service. It also registers a handler for SPCI SMCs exported by
the SPM dispatcher.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I2183adf826d08ff3fee9aee75f021021162b6477

This patch adds a rudimentary SPM dispatcher component in EL3.
It does the following:

- Consumes the TOS_FW_CONFIG to determine properties of the SPM core
  component
- Initialises the SPM core component which resides in the BL32 image
- Implements a handler for SPCI calls from either security state. Some
  basic validation is done for each call but in most cases it is simply
  forwarded as-is to the "other" security state.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I7d116814557f7255f4f4ebb797d1619d4fbab590

This patch reserves and maps the Trusted DRAM for SPM core execution.
It also configures the TrustZone address space controller to run BL31
in secure DRAM.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I7e1bb3bbc61a0fec6a9cb595964ff553620c21dc

This patch repurposes the TOS FW configuration file as the manifest for
the SPM core component which will reside at the secure EL adjacent to
EL3. The SPM dispatcher component will use the manifest to determine how
the core component must be initialised. Routines and data structure to
parse the manifest have also been added.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: Id94f8ece43b4e05609f0a1d364708a912f6203cb

* changes:
  plat/arm: add board support for rd-daniel platform
  plat/arm/sgi: move GIC related constants to board files
  platform/arm/sgi: add multi-chip mode parameter in HW_CONFIG dts
  board/rdn1edge: add support for dual-chip configuration
  drivers/arm/scmi: allow use of multiple SCMI channels
  drivers/mhu: derive doorbell base address
  plat/arm/sgi: include AFF3 affinity in core position calculation
  plat/arm/sgi: add macros for remote chip device region
  plat/arm/sgi: add chip_id and multi_chip_mode to platform variant info
  plat/arm/sgi: move bl31_platform_setup to board file

Currently sptool generates a single blob containing all the Secure
Partitions, with latest SPM implementation, it is desirable to have
individual blobs for each Secure Partition. It allows to leverage
packaging and parsing of SP on existing FIP framework. It also allows
SP packages coming from different sources.

This patch modifies sptool so that it takes number of SP payload pairs
as input and generates number of SP blobs instead of a single blob.

Each SP blob can optionally have its own header containing offsets and
sizes of different payloads along with a SP magic number and version.
It is also associated in FIP with a UUID, provided by SP owner.

Usage example:
sptool -i sp1.bin:sp1.dtb -o sp1.pkg -i sp2.bin:sp2.dtb -o sp2.pkg ...
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ie2db8e601fa1d4182d0a1d22e78e9533dce231bc

At the moment, address demangling is only used by the backtrace
functionality. However, at some point, other parts of the TF-A
codebase may want to use it.
The 'demangle_address' function is replaced with a single XPACI
instruction which is also added in 'do_crash_reporting()'.
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Change-Id: I4424dcd54d5bf0a5f9b2a0a84c4e565eec7329ec

* changes:
  board/rde1edge: fix incorrect topology tree description
  plat/arm/sgi: introduce number of chips macro

Add the initial board support for RD-Daniel Config-M platform.

Change-Id: I36df16c745bfe4bc817e275ad4722e5de57733cd
Signed-off-by: Jagadeesh Ujja <jagadeesh.ujja@arm.com>
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

RD-E1-Edge platform consists of two clusters with eight CPUs each and
two processing elements (PE) per CPU. Commit a9fbf13e

 (plat/arm/sgi:
move topology information to board folder) defined the RD-E1-Edge
topology tree to have two clusters with eight CPUs each but PE per CPU
entries were not added. This patch fixes the topology tree accordingly.

Change-Id: I7f97f0013be60e5d51c214fce3962e246bae8a0b
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>