GitLab

Normally the CP MSS CPU was started at the end of FW load to IRAM at BL2.
However, (especailly in secure boot mode), some bus attributes should be
changed from defaults before the MSS CPU tries to access shared resources.
This patch starts to use CP MSS SRAM for FW load in both secure and
non-secure boot modes.
The FW loader inserts a magic number into MSS SRAM as an indicator of
successfully loaded FS during the BL2 stage and skips releasing the MSS
CPU from the reset state.
Then, at BL31 stage, the MSS CPU is released from reset following the
call to cp110_init function that handles all the required bus attributes
configurations.

Change-Id: Idcf81cc350a086835abed365154051dd79f1ce2e
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/46890

Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>

Wrong brakets caused MSS FW load timeout error:
ERROR:   MSS DMA failed (timeout)
ERROR:   MSS FW chunk 0 load failed
ERROR:   SCP Image load failed

This patch fixes the operator precedence in MSS FW load.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: I78c215606bde112f40429926c51f5fa1e4334c13

This patch cleans up the MSS SRAM if it was used for MSS image
copy (secure boot mode).

Change-Id: I23f600b512050f75e63d59541b9c21cef21ed313
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/30099

Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>

The CP MSS IRAM is only accessible by CM3 CPU and MSS DMA.
In secure boot mode the MSS DMA is unable to directly load
the MSS FW image from DRAM to IRAM.
This patch adds support for using the MSS SRAM as intermediate
storage. The MSS FW image is loaded by application CPU into the
MSS SRAM first, then transferred to MSS IRAM by MSS DMA.
Such change allows the CP MSS image load in secure mode.

Change-Id: Iee7a51d157743a0bdf8acb668ee3d599f760a712
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaszczyk@marvell.com>

Now when mg_conf_cm3 driver is present - move all relevant code there.

Change-Id: I444d9e877c450d6ee69ca3a49b547e4c3aeac0be
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

As a preparation for upcoming support for CN9130 platform, which is
classified as OcteonTx2 product but inherits functionality from a8k,
allow to use a8k_common.mk and mss_common.mk from outside of
PLAT_FAMILY_BASE.
Above is done by introducing BOARD_DIR which needs to be set by each
platform, before including a8k_common.mk and mss_common.mk. This will
allow to use mentioned mk files not only for platforms located under
previously defined PLAT_FAMILY_BASE.

Change-Id: I22356c99bc0419a40ae11e42f37acd50943ea134
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
plat, include/plat) are moved to the new "armada" sub-folder.

Change-Id: Icf03356187078ad6a2e56c9870992be3ca4c9655
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>