GitLab

This reverts commit 2f18aa1f

.

It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.

Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size of BL31 has been increased in builds with SPM.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.

The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.

Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

On some build configurations BL31 is running out of space.  Now that
TSP is moved to secure dram, we have a bit of additional space to use
in BL31.

Change-Id: Ib89fcd8bae99c85c9c5e5d9228bb42fb7048dcb6
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Signed-off-by: David Cunado <david.cunado@arm.com>

To allow BL31 to grow in SRAM, move TSP in TZC secured DRAM
by default.

Increase the BL31 max limit by one page.

Change-Id: Idd3479be02f0f9bafac2f275376d7db0c2015431
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

A new platform define, `PLAT_SP_IMAGE_XLAT_SECTION_NAME`, has been
introduced to select the section where the translation tables used by
the S-EL1/S-EL0 are placed.

This define has been used to move the translation tables to DRAM secured
by TrustZone.

Most of the extra needed space in BL31 when SPM is enabled is due to the
large size of the translation tables. By moving them to this memory
region we can save 44 KiB.

A new argument has been added to REGISTER_XLAT_CONTEXT2() to specify the
region where the translation tables have to be placed by the linker.

Change-Id: Ia81709b4227cb8c92601f0caf258f624c0467719
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch fixes a couple of issues for AArch32 builds on ARM reference
platforms :

1. The arm_def.h previously defined the same BL32_BASE value for AArch64 and
   AArch32 build. Since BL31 is not present in AArch32 mode, this meant that
   the BL31 memory is empty when built for AArch32. Hence this patch allocates
   BL32 to the memory region occupied by BL31 for AArch32 builds.

   As a side-effect of this change, the ARM_TSP_RAM_LOCATION macro cannot
   be used to control the load address of BL32 in AArch32 mode which was
   never the intention of the macro anyway.

2. A static assert is added to sp_min linker script to check that the progbits
   are within the bounds expected when overlaid with other images.

3. Fix specifying `SPD` when building Juno for AArch32 mode. Due to the quirks
   involved when building Juno for AArch32 mode, the build option SPD needed to
   specifed. This patch corrects this and also updates the documentation in the
   user-guide.

4. Exclude BL31 from the build and FIP when building Juno for AArch32 mode. As
   a result the previous assumption that BL31 must be always present is removed
   and the certificates for BL31 is only generated if `NEED_BL31` is defined.

Change-Id: I1c39bbc0abd2be8fbe9f2dea2e9cb4e3e3e436a8
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This initial port of the Secure Partitions Manager to FVP supports BL31
in both SRAM and Trusted DRAM.

A document with instructions to build the SPM has been added.

Change-Id: I4ea83ff0a659be77f2cd72eaf2302cdf8ba98b32
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Achin Gupta <achin.gupta@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

For Trusted Board Boot, BL2 needs more space to support the ECDSA
and ECDSA+RSA algorithms.

Change-Id: Ie7eda9a1315ce836dbc6d18d6588f8d17891a92d
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>

Provides GICv3 save/restore feature to arm_system_pwr_domain_resume and
arm_system_pwr_domain_save functions.

Introduce FVP PSCI power level 3 (System level) support. This is solely
done to provide example code on how to use the GICv3 save and restore
helpers.

Also make CSS GICv3 platforms power off the Redistributor on SYSTEM
SUSPEND as its state is saved and restored.

Change-Id: I0d852f3af8824edee1a17c085cf593ddd33a4e77
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Co-Authored-by: Douglas Raillard <douglas.raillard@arm.com>

The MEM_PROTECT support adds a MMAP region for DRAM2, which when
building with TBBR support and OP-TEE tsp requires an additional
entry in the MMAP region array in BL2 - PLAT_ARM_MMAP_ENTRIES is
increased.

The MEM_PROTECT support also adds a new region in BL31, and when
BL31 is placed in DRAM, the memory mappings require an additional
translation table - MAX_XLAT_TABLES is increased.

Change-Id: I0b76260da817dcfd0b8f73a7193c36efda977625
Signed-off-by: David Cunado <david.cunado@arm.com>

mem_protect needs some kind of non-volatile memory because it has
to remember its state across reset and power down events.
The most suitable electronic part for this feature is a NVRAM
which should be only accesible from the secure world. Juno and
FVP lack such hardware and for this reason the MEM_PROTECT
functionality is implemented with Flash EEPROM memory on both
boards, even though this memory is accesible from the non-secure
world. This is done only to show a full implementation of
these PSCI features, but an actual system shouldn't use a
non-secure NVRAM to implement it.

The EL3 runtime software will write the mem_protect flag and BL2
will read and clear the memory ranges if enabled. It is done in
BL2 because it reduces the time that TF needs access to the full
non-secure memory.

The memory layout of both boards is defined using macros which
take different values in Juno and FVP platforms. Generic platform
helpers are added that use the platform specific macros to generate
a mem_region_t that is valid for the platform.

Change-Id: I2c6818ac091a2966fa07a52c5ddf8f6fde4941e9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

For Trusted Board Boot, BL1 RW section and BL2 need more space to
support the ECDSA algorithm. Specifically, PLAT_ARM_MAX_BL1_RW_SIZE
is increased on ARM platforms.

And on the Juno platform:
    - BL2 size, PLAT_ARM_MAX_BL2_SIZE is increased.
    - SCP_BL2 is loaded into the space defined by BL31_BASE ->
      BL31_RW_BASE. In order to maintain the same size space for
      SCP_BL2,PLAT_ARM_MAX_BL31_SIZE is increased.

Change-Id: I379083f918b40ab1c765da4e71780d89f0058040
Co-Authored-By: David Cunado <david.cunado@arm.com>
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>

NOR memory only supports setting bits to 1. To clear a bit, set to zero,
the NOR memory needs to be erased.

Change-Id: Ia82eb15a5af9a6d4fc7e5ea2b58e6db87226b351
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

lock/unlock operation must wait until WSM bit
is set. Since we do not allow to loop forever then these functions
must return an error if WSM bit isn't enabled after a number of tries.

Change-Id: I21c9e292b514b28786ff4a225128bcd8c1bfa999
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

On ARM platforms before exiting from SP_MIN ensure that
the default console is switched to the runtime serial port.

Change-Id: I0ca0d42cc47e345d56179eac16aa3d6712767c9b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Platforms aligned with TBBR are supposed to use their own OIDs, but
defining the same macros with different OIDs does not provide any
value (at least technically).

For easier use of TBBR, this commit allows platforms to reuse the OIDs
obtained by ARM Ltd.  This will be useful for non-ARM vendors that
do not need their own extension fields in their certificate files.

The OIDs of ARM Ltd. have been moved to include/tools_share/tbbr_oid.h

Platforms can include <tbbr_oid.h> instead of <platform_oid.h> by
defining USE_TBBR_DEFS as 1.  USE_TBBR_DEFS is 0 by default to keep the
backward compatibility.

For clarification, I inserted a blank line between headers from the
include/ directory (#include <...>) and ones from a local directory
(#include "..." ).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

utils.h is included in various header files for the defines in it.
Some of the other header files only contain defines.  This allows the
header files to be shared between host and target builds for shared defines.

Recently types.h has been included in utils.h as well as some function
prototypes.

Because of the inclusion of types.h conflicts exist building host tools
abd these header files now.  To solve this problem,
move the defines to utils_def.h and have this included by utils.h and
change header files to only include utils_def.h and not pick up the new
types.h being introduced.

Fixes ARM-software/tf-issues#461
Signed-off-by: Scott Branden <scott.branden@broadcom.com>

Remove utils_def.h from utils.h

This patch removes utils_def.h from utils.h as it is not required.
And also makes a minor change to ensure Juno platform compiles.

Change-Id: I10cf1fb51e44a8fa6dcec02980354eb9ecc9fa29

ARM platforms have migrated to the translation tables library v2.
However, for testing purposes, it can be useful to temporarily switch
back to the old version.

This patch introduces the option `ARM_XLAT_TABLES_LIB_V1`, that switches
to v1 of the library when is set to 1. By default, it is 0, so that ARM
platforms use the new version unless specifically stated.

Updated User Guide.

Change-Id: I53d3c8dd97706f6af9c6fca0364a88ef341efd31
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Some header files using the ULL() macro were not directly including
utils.h where the macro definition resides. As a consequence, a linker
script with values using this macro did not see the macro definition
and kept the "ULL(<value>)" call in the preprocessed file, which lead to
link error.

Files using ULL() macro now include utils.h directly.

Change-Id: I433a7f36bd21a156c20e69bc2a2bb406140ebdf9
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Modify ARM common makefile to use version 2 of the translation tables
library and include the new header in C files.

Simplify header dependencies related to this library to simplify the
change.

The following table contains information about the size increase in
bytes for BL1 after applying this patch. The code has been compiled for
different configurations of FVP in AArch64 mode with compiler GCC 4.9.3
20150413. The sizes have been calculated with the output of `nm` by
adding the size of all regions and comparing the total size before and
after the change. They are sumarized in the table below:

                               text   bss   data  total
        Release                +660   -20    +88   +728
        Debug                  +740   -20   +242   +962
        Debug (LOG_LEVEL=50)  +1120   -20   +317  +1417

Change-Id: I539e307f158ab71e3a8b771640001fc1bf431b29
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Added APIs to add and remove regions to the translation tables
dynamically while the MMU is enabled. Only static regions are allowed
to overlap other static ones (for backwards compatibility).

A new private attribute (MT_DYNAMIC / MT_STATIC) has been added to
flag each region as such.

The dynamic mapping functionality can be enabled or disabled when
compiling by setting the build option PLAT_XLAT_TABLES_DYNAMIC to 1
or 0. This can be done per-image.

TLB maintenance code during dynamic table mapping and unmapping has
also been added.

Fixes ARM-software/tf-issues#310

Change-Id: I19e8992005c4292297a382824394490c5387aa3b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

With GCC 6.2 compiler, more C undefined behaviour is being flagged as
warnings, which result in build errors in ARM TF build.

The specific issue that this patch resolves is the use of (1 << 31),
which is predominantly used in case statements, where 1 is represented
as a signed int. When shifted to msb the behaviour is undefined.

The resolution is to specify 1 as an unsigned int using a convenience
macro ULL(). A duplicate macro MAKE_ULL() is replaced.

Fixes ARM-software/tf-issues#438

Change-Id: I08e3053bbcf4c022ee2be33a75bd0056da4073e1
Signed-off-by: David Cunado <david.cunado@arm.com>

One nasty part of ATF is some of boolean macros are always defined
as 1 or 0, and the rest of them are only defined under certain
conditions.

For the former group, "#if FOO" or "#if !FOO" must be used because
"#ifdef FOO" is always true.  (Options passed by $(call add_define,)
are the cases.)

For the latter, "#ifdef FOO" or "#ifndef FOO" should be used because
checking the value of an undefined macro is strange.

Here, IMAGE_BL* is handled by make_helpers/build_macro.mk like
follows:

  $(eval IMAGE := IMAGE_BL$(call uppercase,$(3)))

  $(OBJ): $(2)
          @echo "  CC      $$<"
          $$(Q)$$(CC) $$(TF_CFLAGS) $$(CFLAGS) -D$(IMAGE) -c $$< -o $$@

This means, IMAGE_BL* is defined when building the corresponding
image, but *undefined* for the other images.

So, IMAGE_BL* belongs to the latter group where we should use #ifdef
or #ifndef.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Compile option `ARM_BOARD_OPTIMISE_MMAP` has been renamed to
`ARM_BOARD_OPTIMISE_MEM` because it now applies not only to defines
related to the translation tables but to the image size as well.

The defines `PLAT_ARM_MAX_BL1_RW_SIZE`, `PLAT_ARM_MAX_BL2_SIZE` and
`PLAT_ARM_MAX_BL31_SIZE` have been moved to the file board_arm_def.h.
This way, ARM platforms no longer have to set their own values if
`ARM_BOARD_OPTIMISE_MEM=0` and they can specify optimized values
otherwise. The common sizes have been set to the highest values used
for any of the current build configurations.

This is needed because in some build configurations some images are
running out of space. This way there is a common set of values known
to work for all of them and it can be optimized for each particular
platform if needed.

The space reserved for BL2 when `TRUSTED_BOARD_BOOT=0` has been
increased. This is needed because when memory optimisations are
disabled the values for Juno of `PLAT_ARM_MMAP_ENTRIES` and
`MAX_XLAT_TABLES` are higher. If in this situation the code is
compiled in debug mode and with "-O0", the code won't fit.

Change-Id: I70a3d8d3a0b0cad1d6b602c01a7ea334776e718e

On ARM CSS platforms, the whole flash used to be mapped as executable.
This is not required, given that the flash is used to store the BL1
and FIP images and:

 - The FIP is not executed in place, its images are copied to RAM
   and executed from there.

 - BL1 is executed in place from flash but only its code needs to be
   mapped as executable and platform code takes care of re-mapping
   BL1's read-only section as executable.

Therefore, this patch now maps the flash as non-executable by default
on these platforms. This increases security by restricting the
executable region to what is strictly needed.

This patch also adds some comments to clarify the memory mapping
attributes on these platforms.

Change-Id: I4db3c145508bea1f43fbe0f6dcd551e1aec1ecd3

This patch adds an option to the ARM common platforms to load BL31 in the
TZC secured DRAM instead of the default secure SRAM.

To enable this feature, set `ARM_BL31_IN_DRAM` to 1 in build options.
If TSP is present, then setting this option also sets the TSP location
to DRAM and ignores the `ARM_TSP_RAM_LOCATION` build flag.

To use this feature, BL2 platform code must map in the DRAM used by
BL31. The macro ARM_MAP_BL31_SEC_DRAM is provided for this purpose.
Currently, only the FVP BL2 platform code maps in this DRAM.

Change-Id: If5f7cc9deb569cfe68353a174d4caa48acd78d67

This patch fixes inconsistencies in bl1_tbbr_image_descs[]
and miscellaneous fixes in Firmware Update code.

Following are the changes:
* As part of the original FWU changes, a `copied_size`
  field was added to `image_info_t`. This was a subtle binary
  compatibility break because it changed the size of the
  `bl31_params_t` struct, which could cause problems if
  somebody used different versions of BL2 or BL31, one with
  the old `image_info_t` and one with the new version.
  This patch put the `copied_size` within the `image_desc_t`.
* EXECUTABLE flag is now stored in `ep_info.h.attr` in place
  of `image_info.h.attr`, associating it to an entrypoint.
* The `image_info.image_base` is only relevant for secure
  images that are copied from non-secure memory into secure
  memory. This patch removes initializing `image_base` for
  non secure images in the bl1_tbbr_image_descs[].
* A new macro `SET_STATIC_PARAM_HEAD` is added for populating
  bl1_tbbr_image_descs[].ep_info/image_info.h members statically.
  The version, image_type and image attributes are now
  populated using this new macro.
* Added PLAT_ARM_NVM_BASE and PLAT_ARM_NVM_SIZE to avoid direct
  usage of V2M_FLASH0_XXX in plat/arm/common/arm_bl1_fwu.c.
* Refactoring of code/macros related to SECURE and EXECUTABLE flags.

NOTE: PLATFORM PORTS THAT RELY ON THE SIZE OF `image_info_t`
      OR USE the "EXECUTABLE" BIT WITHIN `image_info_t.h.attr`
      OR USE THEIR OWN `image_desc_t` ARRAY IN BL1, MAY BE
      BROKEN BY THIS CHANGE. THIS IS CONSIDERED UNLIKELY.

Change-Id: Id4e5989af7bf0ed263d19d3751939da1169b561d

`board_arm_def.h` contains multiple definitions of
`PLAT_ARM_MMAP_ENTRIES` and `MAX_XLAT_TABLES` that are optimised for
memory usage depending upon the chosen build configuration. To ease
maintenance of these constants, this patch replaces their multiple
definitions with a single set of definitions that will work on all ARM
platforms.

Platforms can override the defaults with optimal values by enabling the
`ARM_BOARD_OPTIMISE_MMAP` build option. An example has been provided in
the Juno ADP port.

Additionally, `PLAT_ARM_MMAP_ENTRIES` is increased by one to accomodate
future ARM platforms.

Change-Id: I5ba6490fdd1e118cc9cc2d988ad7e9c38492b6f0

The debug prints used to debug translation table setup in xlat_tables.c
used the `printf()` standard library function instead of the stack
optimized `tf_printf()` API. DEBUG_XLAT_TABLE option was used to enable
debug logs within xlat_tables.c and it configured a much larger stack
size for the platform in case it was enabled. This patch modifies these
debug prints within xlat_tables.c to use tf_printf() and modifies the format
specifiers to be compatible with tf_printf(). The debug prints are now enabled
if the VERBOSE prints are enabled in Trusted Firmware via LOG_LEVEL build
option.

The much larger stack size definition when DEBUG_XLAT_TABLE is defined
is no longer required and the platform ports are modified to remove this
stack size definition.

Change-Id: I2f7d77ea12a04b827fa15e2adc3125b1175e4c23

This patch replaces all references to the SCP Firmware (BL0, BL30,
BL3-0, bl30) with the image terminology detailed in the TF wiki
(https://github.com/ARM-software/arm-trusted-firmware/wiki):

    BL0          -->  SCP_BL1
    BL30, BL3-0  -->  SCP_BL2
    bl30         -->  scp_bl2

This change affects code, documentation, build system, tools and
platform ports that load SCP firmware. ARM plaforms have been
updated to the new porting API.

IMPORTANT: build option to specify the SCP FW image has changed:

    BL30 --> SCP_BL2

IMPORTANT: This patch breaks compatibility for platforms that use BL2
to load SCP firmware. Affected platforms must be updated as follows:

    BL30_IMAGE_ID --> SCP_BL2_IMAGE_ID
    BL30_BASE --> SCP_BL2_BASE
    bl2_plat_get_bl30_meminfo() --> bl2_plat_get_scp_bl2_meminfo()
    bl2_plat_handle_bl30() --> bl2_plat_handle_scp_bl2()

Change-Id: I24c4c1a4f0e4b9f17c9e4929da815c4069549e58

This patch applies the TBBR naming convention to the certificates
and the corresponding extensions defined by the CoT:

    * Certificate UUID names
    * Certificate identifier names
    * OID names

Changes apply to:

    * Generic code (variables and defines)
    * The default certificate identifiers provided in the generic
      code
    * Build system
    * ARM platforms port
    * cert_create tool internal definitions
    * fip_create and cert_create tools command line options
    * Documentation

IMPORTANT: this change breaks the compatibility with platforms
that use TBBR. The platform will need to adapt the identifiers
and OIDs to the TBBR naming convention introduced by this patch:

Certificate UUIDs:

    UUID_TRUSTED_BOOT_FIRMWARE_BL2_CERT --> UUID_TRUSTED_BOOT_FW_CERT
    UUID_SCP_FIRMWARE_BL30_KEY_CERT --> UUID_SCP_FW_KEY_CERT
    UUID_SCP_FIRMWARE_BL30_CERT --> UUID_SCP_FW_CONTENT_CERT
    UUID_EL3_RUNTIME_FIRMWARE_BL31_KEY_CERT --> UUID_SOC_FW_KEY_CERT
    UUID_EL3_RUNTIME_FIRMWARE_BL31_CERT --> UUID_SOC_FW_CONTENT_CERT
    UUID_SECURE_PAYLOAD_BL32_KEY_CERT --> UUID_TRUSTED_OS_FW_KEY_CERT
    UUID_SECURE_PAYLOAD_BL32_CERT --> UUID_TRUSTED_OS_FW_CONTENT_CERT
    UUID_NON_TRUSTED_FIRMWARE_BL33_KEY_CERT --> UUID_NON_TRUSTED_FW_KEY_CERT
    UUID_NON_TRUSTED_FIRMWARE_BL33_CERT --> UUID_NON_TRUSTED_FW_CONTENT_CERT

Certificate identifiers:

    BL2_CERT_ID --> TRUSTED_BOOT_FW_CERT_ID
    BL30_KEY_CERT_ID --> SCP_FW_KEY_CERT_ID
    BL30_CERT_ID --> SCP_FW_CONTENT_CERT_ID
    BL31_KEY_CERT_ID --> SOC_FW_KEY_CERT_ID
    BL31_CERT_ID --> SOC_FW_CONTENT_CERT_ID
    BL32_KEY_CERT_ID --> TRUSTED_OS_FW_KEY_CERT_ID
    BL32_CERT_ID --> TRUSTED_OS_FW_CONTENT_CERT_ID
    BL33_KEY_CERT_ID --> NON_TRUSTED_FW_KEY_CERT_ID
    BL33_CERT_ID --> NON_TRUSTED_FW_CONTENT_CERT_ID

OIDs:

    TZ_FW_NVCOUNTER_OID --> TRUSTED_FW_NVCOUNTER_OID
    NTZ_FW_NVCOUNTER_OID --> NON_TRUSTED_FW_NVCOUNTER_OID
    BL2_HASH_OID --> TRUSTED_BOOT_FW_HASH_OID
    TZ_WORLD_PK_OID --> TRUSTED_WORLD_PK_OID
    NTZ_WORLD_PK_OID --> NON_TRUSTED_WORLD_PK_OID
    BL30_CONTENT_CERT_PK_OID --> SCP_FW_CONTENT_CERT_PK_OID
    BL30_HASH_OID --> SCP_FW_HASH_OID
    BL31_CONTENT_CERT_PK_OID --> SOC_FW_CONTENT_CERT_PK_OID
    BL31_HASH_OID --> SOC_AP_FW_HASH_OID
    BL32_CONTENT_CERT_PK_OID --> TRUSTED_OS_FW_CONTENT_CERT_PK_OID
    BL32_HASH_OID --> TRUSTED_OS_FW_HASH_OID
    BL33_CONTENT_CERT_PK_OID --> NON_TRUSTED_FW_CONTENT_CERT_PK_OID
    BL33_HASH_OID --> NON_TRUSTED_WORLD_BOOTLOADER_HASH_OID
    BL2U_HASH_OID --> AP_FWU_CFG_HASH_OID
    SCP_BL2U_HASH_OID --> SCP_FWU_CFG_HASH_OID
    NS_BL2U_HASH_OID --> FWU_HASH_OID

Change-Id: I1e047ae046299ca913911c39ac3a6e123bd41079

This patch adds support for Firmware update in BL2U for ARM
platforms such that TZC initialization is performed on all
ARM platforms and (optionally) transfer of SCP_BL2U image on
ARM CSS platforms.

BL2U specific functions are added to handle early_platform and
plat_arch setup. The MMU is configured to map in the BL2U
code/data area and other required memory.

Change-Id: I57863295a608cc06e6cbf078b7ce34cbd9733e4f

This patch adds Firmware Update support for ARM platforms.

New files arm_bl1_fwu.c and juno_bl1_setup.c were added to provide
platform specific Firmware update code.

BL1 now includes mmap entry for `ARM_MAP_NS_DRAM1` to map DRAM for
authenticating NS_BL2U image(For both FVP and JUNO platform).

Change-Id: Ie116cd83f5dc00aa53d904c2f1beb23d58926555

This patch overrides the default weak definition of
`bl31_plat_runtime_setup()` for ARM Standard platforms to
specify a BL31 runtime console. ARM Standard platforms are
now expected to define `PLAT_ARM_BL31_RUN_UART_BASE` and
`PLAT_ARM_BL31_RUN_UART_CLK_IN_HZ` macros which is required
by `arm_bl31_plat_runtime_setup()` to initialize the runtime
console.

The system suspend resume helper `arm_system_pwr_domain_resume()`
is fixed to initialize the runtime console rather than the boot
console on resumption from system suspend.

Fixes ARM-software/tf-issues#220

Change-Id: I80eafe5b6adcfc7f1fdf8b99659aca1c64d96975

This patch fixes several issues with the SP804 delay timer on FVP:

* By default, the SP804 dual timer on FVP runs at 32 KHz. In order
  to run the timer at 35 MHz (as specified in the FVP user manual)
  the Overwrite bit in the SP810 control register must be set.

* The CLKMULT and CLKDIV definitions are mixed up:

      delta(us) = delta(ticks) * T(us) = delta(ticks) / f(MHz)

  From the delay function:

      delta_us = (delta * ops->clk_mult) / ops->clk_div;

  Matching both expressions:

      1 / f(MHz) = ops->clk_mult / ops->clk_div

  And consequently:

      f(MHz) = ops->clk_div / ops->clk_mult

  Which, for a 35 MHz timer, translates to:

      ops->clk_div = 35
      ops->clk_mult = 1

* The comment in the delay timer header file has been corrected:
  The ratio of the multiplier and the divider is the clock period
  in microseconds, not the frequency.

Change-Id: Iffd5ce0a5a28fa47c0720c0336d81b678ff8fdf1

This patch adds watchdog support on ARM platforms (FVP and Juno).
A secure instance of SP805 is used as Trusted Watchdog. It is
entirely managed in BL1, being enabled in the early platform setup
hook and disabled in the exit hook. By default, the watchdog is
enabled in every build (even when TBB is disabled).

A new ARM platform specific build option `ARM_DISABLE_TRUSTED_WDOG`
has been introduced to allow the user to disable the watchdog at
build time. This feature may be used for testing or debugging
purposes.

Specific error handlers for Juno and FVP are also provided in this
patch. These handlers will be called after an image load or
authentication error. On FVP, the Table of Contents (ToC) in the FIP
is erased. On Juno, the corresponding error code is stored in the
V2M Non-Volatile flags register. In both cases, the CPU spins until
a watchdog reset is generated after 256 seconds (as specified in
the TBBR document).

Change-Id: I9ca11dcb0fe15af5dbc5407ab3cf05add962f4b4

This patch adds ARM specific OIDs which will be used to extract
the extension data from the certificates. These OIDs are arranged
as a subtree whose root node has been specifically allocated for
ARM Ltd.

    { iso(1) identified-organization(3) dod(6) internet(1)
      private(4) enterprise(1) 4128 }

Change-Id: Ice20b3c8a31ddefe9102f3bd42f7429986f3ac34