Skip to content

GitLab

Switch branch/tag
  1. 04 Sep, 2018 5 commits
    • Bryan O'Donoghue's avatar
      imx: imx_clock: wdog: Add watchdog clock API · bbdcdd04
      Bryan O'Donoghue authored 
      

This patch adds a set of functions to enable the clock for each of the
watchdog IP blocks.

Unlike the MMC and UART blocks, the watchdog blocks operate off of the one
root clock, only the clock-gates are enable/disabled individually.

As a consequence the function clock_set_wdog_clk_root_bits() is used to set
the root-slice just once for all of the watchdog blocks.

Future implementations may need to change this model but for now on the one
supported processor and similar NXP SoCs this model should work fine.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      bbdcdd04
    • Jun Nie's avatar
      imx: imx_clock: mmc: Add USDHC clock API · 14cf32aa
      Jun Nie authored 
      

This patch adds an API to configure up the base USDHC clocks, taking a
bit-mask of silicon specific bits as an input from a higher layer in order
to direct the necessary clock source.
Signed-off-by: default avatarJun Nie <jun.nie@linaro.org>
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      14cf32aa
    • Bryan O'Donoghue's avatar
      imx: imx_clock: uart: Add UART clock API · dcd54e9b
      Bryan O'Donoghue authored 
      

This patch adds an API to configure up the base UART clocks, taking a
bit-mask of silicon specific bits as an input from a higher layer in order
to direct the necessary clock source.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      dcd54e9b
    • Bryan O'Donoghue's avatar
      imx: imx_clock: Add driver and associated clock register definitions · 82e35083
      Bryan O'Donoghue authored 
      

This commit:

- Defines a clock stub with a conjoined header defining the clock
  memory map.

- Defines the CCM Clock Gating Register which comes in a quadrumvirate
  register set to read, set, clear and toggle individual clock gates into
  one of four states based bitmask.

  00: Domain clocks not needed
  01: Domain clocks needed when in RUN
  10: Domain clocks needed when in RUN and WAIT
  11: Domain clocks needed all the time

- Defines clock control register bits

  There are various quadrumvirate register blocks target-root, misc-root,
  post-root, pre-root in the CCM.

  The number of registers is huge but the four registers in each
  quadrumvirate block contain the same bits, so the number of bit
  definitions is actually quite low.

- Defines clock identifiers

  An array of clock gates is provided in the CCM block. In order to index
  that array and thus enable/disable clock gates for the right components,
  we need to provide meaningful names to the indices.

  Section 5.2.5 of the i.MX7 Solo Application Processor Reference Manual
  Rev 0.1 provides the relevant details.

- Defines target mux select bits
  This is a comprehensive definition of the target clock mux select bits.
  These bits are required to correctly select the clock source. Defining
  all of the bits up-front even for unused blocks in ATF means we can
  switch on any block we want at a later date without having to write new
  code in the clock-mux layer.

- Defines identifier indices into root-slice array
  The root-slice array of control registers has a specific set of indices,
  which differ from the clock-gate indices.

- Provides a clock gate enable/disable routine
  Provides a clock-gate enable/disable routine via the set/clr
  registers in a given clock-gate control register block.

  This index passed should be one of the enums associated with CCM and
  depending on enable/disable being passed either set or clr will be
  written to.

  The Domain0 bits are currently the only bits targeted by this write, more
  work may need to be done on the domain bits in subsequent patches as a
  result.

- imx: Adds set/clr routines to clock layer

  Adds a set and clr routine to the clock layer. These routines allow us to
  access the set and clear registers of the "target" block registers. These
  are the registers where we select the clock source from the available list.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      82e35083
    • Bryan O'Donoghue's avatar
      imx7: imx_regs: Add a shared imx-regs.h for i.MX7 ATF platforms · 7d464592
      Bryan O'Donoghue authored 
      

In order to have some common code shared between similar SOCs its pretty
common to have IP blocks reused. In reusing those blocks we frequently need
to map compatible blocks to different addresses depending on the SOC.

This patch adds a basic memory map of the i.MX7 based on the "Cortex-A7
Memory Map" section 2.12 of "i.MX7Solo Applications Processor Reference
Manual, Rev 0.1 08/2016"

In memory map terms the i.MX7S and i.MX7D are identical with the D
variant containing two Cortex-A7 cores plus a Cortex-M core and the S
variant containing one Cortex-A7 and one Cortex-M.
Signed-off-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
      7d464592
  3. 30 Aug, 2018 3 commits
  5. 23 Aug, 2018 1 commit
  7. 22 Aug, 2018 10 commits
  9. 21 Aug, 2018 1 commit
  11. 20 Aug, 2018 1 commit
  13. 19 Aug, 2018 1 commit
  15. 17 Aug, 2018 1 commit
  17. 15 Aug, 2018 2 commits
  19. 10 Aug, 2018 6 commits
  21. 06 Aug, 2018 1 commit
  23. 03 Aug, 2018 7 commits
  25. 01 Aug, 2018 1 commit
    • Daniel Boulby's avatar
      Fix build for SEPARATE_CODE_AND_RODATA=0 · 2ecaafd2
      Daniel Boulby authored 
      

TF won't build since no memory region is specified
for when SEPARATE_CODE_AND_RODATA=0 it still relies on
the ARM_MAP_BL_RO_DATA region which is never defined for
this case. Create memory region combining code and RO data for
when the build flag SEPARATE_CODE_AND_RODATA=0 to fix this

Change-Id: I6c129eb0833497710cce55e76b8908ce03e0a638
Signed-off-by: default avatarDaniel Boulby <daniel.boulby@arm.com>
      2ecaafd2