GitLab

This patch changes implementation for disabling Secure Cycle
Counter. For ARMv8.5 the counter gets disabled by setting
SDCR.SCCD bit on CPU cold/warm boot. For the earlier
architectures PMCR register is saved/restored on secure
world entry/exit from/to Non-secure state, and cycle counting
gets disabled by setting PMCR.DP bit.
In 'include\aarch32\arch.h' header file new
ARMv8.5-PMU related definitions were added.

Change-Id: Ia8845db2ebe8de940d66dff479225a5b879316f8
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch introduces an additional precautionary step to further
enhance protection against variant 4. During the context initialisation
before we enter the various BL stages, the SPSR.SSBS bit is explicitly
set to zero. As such, speculative loads/stores are by default disabled
for all BL stages when they start executing. Subsequently, each BL
stage, can choose to enable speculative loads/stores or keep them
disabled.

This change doesn't affect the initial execution context of BL33 which
is totally platform dependent and, thus, it is intentionally left up to
each platform to initialise.

For Arm platforms, SPSR.SSBS is set to zero for BL33 too. This means
that, for Arm platforms, all BL stages start with speculative
loads/stores disabled.

Change-Id: Ie47d39c391d3f20fc2852fc59dbd336f8cacdd6c
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

Those defines are used in STM32MP1 clock driver.
It is better to put them altogether with already defined registers.

Change-Id: I6f8ad8c2477b947af6f76283a4ef5c40212d0027
Signed-off-by: Yann Gautier <yann.gautier@st.com>

The workarounds for these errata are so closely related that it is
better to only have one patch to make it easier to understand.

Change-Id: I0287fa69aefa8b72f884833f6ed0e7775ca834e9
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

In a system with ARMv8.5-PMU implemented:

- If EL3 is using AArch32, setting MDCR_EL3.SCCD to 1 disables counting
  in Secure state in PMCCNTR.

- If EL3 is using AArch64, setting SDCR.SCCD to 1 disables counting in
  Secure state in PMCCNTR_EL0.

So far this effect has been achieved by setting PMCR_EL0.DP (in AArch64)
or PMCR.DP (in AArch32) to 1 instead, but this isn't considered secure
as any EL can change that value.

Change-Id: I82cbb3e48f2e5a55c44d9c4445683c5881ef1f6f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The Generic Timer is an optional extension to an ARMv7-A implementation.
The generic delay timer can be used from any architecture supported by
the Trusted Firmware. In ARMv7 it is needed to check that this feature
is present. In ARMv8 it is always present.

Change-Id: Ib7e8ec13ffbb2f64445d4ee48ed00f26e34b79b7
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

ARMv8.2-TTCNP is mandatory from ARMv8.2 onwards, but it can be implemented
in CPUs that don't implement all mandatory 8.2 features (and so have to
claim to be a lower version).

This patch removes usage of the ARM_ARCH_AT_LEAST() macro and uses system
ID registers to detect whether it is needed to set the bit or not.

Change-Id: I7bcbf0c7c937590dfc2ca668cfd9267c50f7d52c
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The architecture dependant header files in include/lib/${ARCH} and
include/common/${ARCH} have been moved to /include/arch/${ARCH}.

Change-Id: I96f30fdb80b191a51448ddf11b1d4a0624c03394
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch enables the Data Independent Timing
functionality (DIT) in EL3 if supported
by the platform.

Change-Id: Ia527d6aa2ee88a9a9fe1c941220404b9ff5567e5
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

The Armv8.5 extensions introduces PSTATE.SSBS (Speculation Store Bypass
Safe) bit to mitigate against Variant 4 vulnerabilities. Although an
Armv8.5 feature, this can be implemented by CPUs implementing earlier
version of the architecture.

With this patch, when both PSTATE.SSBS is implemented and
DYNAMIC_WORKAROUND_CVE_2018_3639 is active, querying for
SMCCC_ARCH_WORKAROUND_2 via. SMCCC_ARCH_FEATURES call would return 1 to
indicate that mitigation on the PE is either permanently enabled or not
required.

When SSBS is implemented, SCTLR_EL3.DSSBS is initialized to 0 at reset
of every BL stage. This means that EL3 always executes with mitigation
applied.

For Cortex A76, if the PE implements SSBS, the existing mitigation (by
using a different vector table, and tweaking CPU ACTLR2) is not used.

Change-Id: Ib0386c5714184144d4747951751c2fc6ba4242b6
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The headers forked at some point in the past and have diverged a lot. In
order to make it easier to share code between TF-A-Tests and TF-A, this
patch synchronises most of the definitions in the mentioned headers.

This is not a complete sync, it has to be followed by more cleanup.

This patch also removes the read helpers for the AArch32 instructions
ats1cpr and ats1hr (they are write-only).

Change-Id: Id13ecd7aeb83bd2318cd47156d71a42f1c9f6ba2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Icd1cdd42afdc78895a9be6c46b414b0a155cfa63
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

PAR register used here is a 64 bit register.
On AARCH32 BIT macro is BIT_32.
PAR_ADDR_MASK should then use BIT_64 to avoid overflow.
Signed-off-by: Yann Gautier <yann.gautier@st.com>

This function diplays the backtrace, the current EL and security state
to allow a post-processing tool to choose the right binary to interpret
the dump.

The output can be fed to GNU addr2line to resolve function names given
an ELF binary compiled with debug information. The "-i" flag is
recommended to improve display in case of inlined functions. The *.dump
files generated during the build process can also be used.

The function works in AArch64 and AArch32. In AArch32 it only works in
A32 mode (without T32 interworking), which is enforced in the Makefile.

Sample output of a backtrace at EL3:

    BACKTRACE: START: function_name
    0: EL3: 0x798
    1: EL3: 0x538
    2: EL3: 0x550
    3: EL3: 0x55c
    4: EL3: 0x568
    5: EL3: 0x5a8
    6: EL3: 0xf4
    BACKTRACE: END: function_name

In order to enable it the new option ENABLE_BACKTRACE must be set to 1.
This option is set to 1 by default only in AArch64 debug builds. As
usual, it can be overridden by the platform makefile and in the build
command line.

Change-Id: Icaff39b0e5188329728be2f3c72b868b2368e794
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

The translation library is useful elsewhere. Even though this repository
doesn't exercise the EL2 support of the library, it is better to have it
here as well to make it easier to maintain.

enable_mmu_secure() and enable_mmu_direct() have been deprecated. The
functions are still present, but they are behind ERROR_DEPRECATED and
they call the new functions enable_mmu_svc_mon() and
enable_mmu_direct_svc_mon().

Change-Id: I13ad10cd048d9cc2d55e0fff9a5133671b67dcba
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I98f23f6cebcf984b57efc5449b75ff702e1984a0
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Define the values as unsigned int or unsigned long long based on the
actual size of the register. This prevents subtle issues caused by
having a type that is too small. For example:

    #define OPTION_ENABLE 0x3
    #define OPTION_SHIFT  32

    uint64_t mask = OPTION_ENABLE << OPTION_SHIFT;

Because OPTION_ENABLE fits in an int, the value is considered an int.
This means that, after shifting it 32 places to the left, the final
result is 0. The correct way to define the values is:

    #define OPTION_ENABLE ULL(0x3)
    #define OPTION_SHIFT  U(32)

In this case, the compiler is forced to use a 64 bit value from the
start, so shifting it 32 places to the left results in the expected
value.

Change-Id: Ieaf2ffc2d8caa48c622db011f2aef549e713e019
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

At present, the function provided by the translation library to enable
MMU constructs appropriate values for translation library, and programs
them to the right registers. The construction of initial values,
however, is only required once as both the primary and secondaries
program the same values.

Additionally, the MMU-enabling function is written in C, which means
there's an active stack at the time of enabling MMU. On some systems,
like Arm DynamIQ, having active stack while enabling MMU during warm
boot might lead to coherency problems.

This patch addresses both the above problems by:

  - Splitting the MMU-enabling function into two: one that sets up
    values to be programmed into the registers, and another one that
    takes the pre-computed values and writes to the appropriate
    registers. With this, the primary effectively calls both functions
    to have the MMU enabled, but secondaries only need to call the
    latter.

  - Rewriting the function that enables MMU in assembly so that it
    doesn't use stack.

This patch fixes a bunch of MISRA issues on the way.

Change-Id: I0faca97263a970ffe765f0e731a1417e43fbfc45
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Currently TF-A doesn't initialise CNTFRQ register in CNTCTLBase
frame of the system timer. ARM ARM states that "The instance of
the register in the CNTCTLBase frame must be programmed with this
value as part of system initialization."

The psci_arch_setup() updates the CNTFRQ system register but
according to the ARM ARM, this instance of the register is
independent of the memory mapped instance. This is only an issue
for Normal world software which relies on the memory mapped
instance rather than the system register one.

This patch resolves the issue for ARM platforms.

The patch also solves a related issue on Juno, wherein
CNTBaseN.CNTFRQ can be written and does not reflect the value of
the register in CNTCTLBase frame. Hence this patch additionally
updates CNTFRQ register in the Non Secure frame of the CNTBaseN.

Fixes ARM-Software/tf-issues#593

Change-Id: I09cebb6633688b34d5b1bc349fbde4751025b350
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Add amu_context_save() and amu_context_restore() functions for aarch32

Change-Id: I4df83d447adeaa9d9f203e16dc5a919ffc04d87a
Signed-off-by: Joel Hutton <joel.hutton@arm.com>

Change-Id: Id6dfe885a63561b1d2649521bd020367b96ae1af
Signed-off-by: Joel Hutton <joel.hutton@arm.com>

This patch introduces two workarounds for ARMv7 systems.  The
workarounds need to be applied prior to any `branch` instruction in
secure world.  This is achieved using a custom vector table where each
entry is an `add sp, sp, #1` instruction.

On entry to monitor mode, once the sequence of `ADD` instructions is
executed, the branch target buffer (BTB) is invalidated.  The bottom
bits of `SP` are then used to decode the exception entry type.

A side effect of this change is that the exception vectors are
installed before the CPU specific reset function.  This is now
consistent with how it is done on AArch64.

Note, on AArch32 systems, the exception vectors are typically tightly
integrated with the secure payload (e.g. the Trusted OS).  This
workaround will need porting to each secure payload that requires it.

The patch to modify the AArch32 per-cpu vbar to the corresponding
workaround vector table according to the CPU type will be done in a
later patch.

Change-Id: I5786872497d359e496ebe0757e8017fa98f753fa
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

The `ENABLE_AMU` build option can be used to enable the
architecturally defined AMU counters.  At present, there is no support
for the auxiliary counter group.

Change-Id: Ifc7532ef836f83e629f2a146739ab61e75c4abc8
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

API documentation updated.

Change-Id: I129725059299af6cc612bafa8d74817f779d7c4f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Currently TF does not initialise the PMCR_EL0 register in
the secure context or save/restore the register.

In particular, the DP field may not be set to one to prohibit
cycle counting in the secure state, even though event counting
generally is prohibited via the default setting of MDCR_EL3.SMPE
to 0.

This patch initialises PMCR_EL0.DP to one in the secure state
to prohibit cycle counting and also initialises other fields
that have an architectually UNKNOWN reset value.

Additionally, PMCR_EL0 is added to the list of registers that are
saved and restored during a world switch.

Similar changes are made for PMCR for the AArch32 execution state.

NOTE: secure world code at lower ELs that assume other values in PMCR_EL0
will be impacted.

Change-Id: Iae40e8c0a196d74053accf97063ebc257b4d2f3a
Signed-off-by: David Cunado <david.cunado@arm.com>

This patch provides helper macros for both Device and Normal memory MAIR
encodings as defined by the ARM Architecture Reference Manual for ARMv8-A
(ARM DDI0487B.A).

Change-Id: I5faae7f2cf366390ad4ba1d9253c6f3b60fd5e20
Signed-off-by: David Cunado <david.cunado@arm.com>

This patch enables the CnP (Common not Private) bit for secure page
tables so that multiple PEs in the same Inner Shareable domain can use
the same translation table entries for a given stage of translation in
a particular translation regime. This only takes effect when ARM
Trusted Firmware is built with ARM_ARCH_MINOR >= 2.

ARM Trusted Firmware Design has been updated to include a description
of this feature usage.

Change-Id: I698305f047400119aa1900d34c65368022e410b8
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>

This patch updates the el3_arch_init_common macro so that it fully
initialises essential control registers rather then relying on hardware
to set the reset values.

The context management functions are also updated to fully initialise
the appropriate control registers when initialising the non-secure and
secure context structures and when preparing to leave EL3 for a lower
EL.

This gives better alignement with the ARM ARM which states that software
must initialise RES0 and RES1 fields with 0 / 1.

This patch also corrects the following typos:

"NASCR definitions" -> "NSACR definitions"

Change-Id: Ia8940b8351dc27bc09e2138b011e249655041cfc
Signed-off-by: David Cunado <david.cunado@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch adds support for SP_MIN on JUNO platform.
The changes include addition of AArch32 assembly files,
JUNO specific SP_MIN make file and miscellaneous changes
in ARM platform files to enable support for SP_MIN.

Change-Id: Id1303f422fc9b98b9362c757b1a4225a16fffc0b
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch adds AArch32 state support for ARM Cortex-A53,
Cortex-A57 and Cortex-A72 MPCore Processor in the CPU specific
operations framework.

NOTE: CPU errata handling code is not present in this patch.

Change-Id: I01eb3e028e40dde37565707ebc99e06e7a0c113d
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch modifies some of the functions in ARM platform layer to cater
for the case when multi-threading `MT` is set in MPIDR. A new build flag
`ARM_PLAT_MT` is added, and when enabled, the functions accessing MPIDR
now assume that the `MT` bit is set for the platform and access the bit
fields accordingly.

Also, a new API plat_arm_get_cpu_pe_count is added when `ARM_PLAT_MT` is
enabled, returning the PE count within the physical cpu corresponding to
`mpidr`.

Change-Id: I04ccf212ac3054a60882761f4087bae299af13cb
Signed-off-by: Summer Qin <summer.qin@arm.com>

Added APIs to add and remove regions to the translation tables
dynamically while the MMU is enabled. Only static regions are allowed
to overlap other static ones (for backwards compatibility).

A new private attribute (MT_DYNAMIC / MT_STATIC) has been added to
flag each region as such.

The dynamic mapping functionality can be enabled or disabled when
compiling by setting the build option PLAT_XLAT_TABLES_DYNAMIC to 1
or 0. This can be done per-image.

TLB maintenance code during dynamic table mapping and unmapping has
also been added.

Fixes ARM-software/tf-issues#310

Change-Id: I19e8992005c4292297a382824394490c5387aa3b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Trusted Firmware currently has no support for secure self-hosted
debug.  To avoid unexpected exceptions, disable software debug
exceptions, other than software breakpoint instruction exceptions,
from all exception levels in secure state.  This applies to both
AArch32 and AArch64 EL3 initialization.

Change-Id: Id097e54a6bbcd0ca6a2be930df5d860d8d09e777
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch resets EL2 and EL3 registers that have architecturally
UNKNOWN values on reset and that also provide EL2/EL3 configuration
and trap controls.

Specifically, the EL2 physical timer is disabled to prevent timer
interrups into EL2 - CNTHP_CTL_EL2 and CNTHP_CTL for AArch64 and AArch32,
respectively.

Additionally, for AArch64, HSTR_EL2 is reset to avoid unexpected traps of
non-secure access to certain system registers at EL1 or lower.

For AArch32, the patch also reverts the reset to SDCR which was
incorrectly added in a previous change.

Change-Id: If00eaa23afa7dd36a922265194ccd6223187414f
Signed-off-by: David Cunado <david.cunado@arm.com>

In order to avoid unexpected traps into EL3/MON mode, this patch
resets the debug registers, MDCR_EL3 and MDCR_EL2 for AArch64,
and SDCR and HDCR for AArch32.

MDCR_EL3/SDCR is zero'ed when EL3/MON mode is entered, at the
start of BL1 and BL31/SMP_MIN.

For MDCR_EL2/HDCR, this patch zero's the bits that are
architecturally UNKNOWN values on reset. This is done when
exiting from EL3/MON mode but only on platforms that support
EL2/HYP mode but choose to exit to EL1/SVC mode.

Fixes ARM-software/tf-issues#430

Change-Id: Idb992232163c072faa08892251b5626ae4c3a5b6
Signed-off-by: David Cunado <david.cunado@arm.com>

The values of CP15BEN, nTWI & nTWE bits in SCTLR_EL1 are architecturally
unknown if EL3 is AARCH64 whereas they reset to 1 if EL3 is AArch32. This
might be a compatibility break for legacy AArch32 normal world software if
these bits are not set to 1 when EL3 is AArch64. This patch enables the
CP15BEN, nTWI and nTWE bits in the SCTLR_EL1 if the lower non-secure EL is
AArch32. This unifies the SCTLR settings for lower non-secure EL in AArch32
mode for both AArch64 and AArch32 builds of Trusted Firmware.

Fixes ARM-software/tf-issues#428

Change-Id: I3152d1580e4869c0ea745c5bd9da765f9c254947
Signed-off-by: Soby Mathew <soby.mathew@arm.com>