This reverts commit 1c297bf0
because it introduced a bug: the CNTFRQ_EL0 register was no
longer programmed by all CPUs.  bl31_platform_setup() function
is invoked only in the cold boot path and consequently only
on the primary cpu.

A subsequent commit will correctly implement the necessary changes
to the counter frequency setup code.

This patch should be integrated into mainline at some point.

Workaround for issue #68

On Juno, we don't need the following components so this patch
removes them of the images:
 - semihosting support;
 - FVP power controller support;
 - GICv3 support.

 - Distinguish Juno specific from platform agnostic constants
 - Define constants for Juno TZC-400 NSAID

It is easier to have all platform constants in the same place.

As for FVP platforms, Juno provides some LEDs that we can
use to report exceptions during the early boot code.

Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

BL30 needs an entry in the table in io_fip.c.  I made it #ifdef'd so
that ports that don't use a BL30 won't break.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>

Removing semihosting from the plat_io_storage code copied from FVP.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>

Juno has a "taped out" BL1.

To run your own BL1 on the board, you have to place it in a "ROM bypass"
address and configure the platform to boot from there.

The agreed bypass address is an offset of 0x03EC0000 from the start of
NOR flash (0x08000000), which equates to 0x0BEC0000.

To run the model using a BL1 in bypass mode, you should use a parameter
set something like this:

	<path to>/FVP_CSS_Juno3 \
		-C css.aon.scp.ROMloader.fname=<SCP ROM filename> \
		--data css.cluster1.cpu0=bl1.bin@0x0BEC0000 \
		-C soc.scc.apps_alt_boot=0x0BEC0000

To build BL1 as a ROM located at address zero, you can over-ride the
default value for TZROM_BASE by passing parameters to make, eg:

	ASFLAGS="-D TZROM_BASE=0x00000000" \
	CFLAGS="-D TZROM_BASE=0x00000000" \
	CROSS_COMPILE=aarch64-linux-gnu- \
	make PLAT=juno DEBUG=1 all

Then you can launch the model using a command such as:

	<path to>/FVP_CSS_Juno3 \
		-C css.aon.scp.ROMloader.fname=<SCP ROM filename> \
		-C css.trustedBootROMloader.fname=<path to>/bl1.bin \
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>

Currently UEFI and Linux are using SMC calls in the 'ARM Architecture'
Owning Entity range so lets implement these to get things working.

UEFI probably doesn't actually need to issue the ID_PRESENCE and ID_UID
calls it does, and the device-tree used by Linux could specify the PSCI
identifiers instead. After those changes, this patch isn't required.
Signed-off-by: Jon Medhurst <tixy@linaro.org>

This is a temporary solution for issue #20
Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

The SCP Ready command is sent by the SCP to indicate that the BL3-0 RAM
Firmware image is successfully up and running.
Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Note, on Juno mailboxes are 16 bytes because any bigger and they would
overlap the memory used for MHU payload data for SCP->AP transfers.
Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

Juno doesn't have TZDRAM as FVP does, and there is real reason why we
need a special memory region for bl31_args anyway, assuming we take care
to copy it in BL31 before BL2's memory is reused.
Signed-off-by: Jon Medhurst <tixy@linaro.org>

Signed-off-by: Jon Medhurst <tixy@linaro.org>

At present, bl1_arch_setup() and bl31_arch_setup() program the counter
frequency using a value from the memory mapped generic timer. The
generic timer however is not necessarily present on all ARM systems
(although it is architected to be present on all server systems).

This patch moves the timer setup to platform-specific code and updates
the relevant documentation. Also, CNTR.FCREQ is set as the specification
requires the bit corresponding to the counter's frequency to be set when
enabling. Since we intend to use the base frequency, set bit 8.

Fixes ARM-software/tf-issues#24

Change-Id: I32c52cf882253e01f49056f47c58c23e6f422652

This patch removes the 'CPU present' flag that's being set but not
referred or used anywhere else.

Change-Id: Iaf82bdb354134e0b33af16c7ba88eb2259b2682a

Remove the instructions to update the change log from
contribution.md. The change log no longer contains a
"Detailed changes since last release" section.

Also, update the documentation links following recent
documentation changes.

Change-Id: Id9df43d666f7f9a60dcc6f663a8a85cdd2ff7cc4