- 13 Mar, 2019 2 commits
-
-
Masahisa Kojima authored
MHU doorbell driver requires arm platform specific macro "PLAT_CSS_MHU_BASE". Rename it to "PLAT_MHUV2_BASE", so that platforms other than arm can use generic MHU doorbell driver. Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
-
Masahisa Kojima authored
Enable the SCMI protocol support in SynQuacer platform. Aside from power domain, system power and apcore management protocol, this commit adds the vendor specific protocol(0x80). This vendor specific protocol is used to get the dram mapping information from SCP. Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
-
- 08 Mar, 2019 4 commits
-
-
Andre Przywara authored
So far the DT node describing the AXP803 PMIC used in many Allwinner A64 boards had only one subnode, so our code just entering the first subnode to find all regulators worked fine. However recent DT updates in the Linux kernel add more subnodes *before* that, so we need to make sure to explicitly enter the "regulators" subnode to find the information we are after. Improve some DT node parsing error handling on the way. Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-
Luca Ceresoli authored
Allow EL2 (e.g. U-Boot) to load the configuration object at runtime into the Xilinx ZynqMP PMU firmware. This allows booting with U-Boot and U-Boot SPL with PMU FW without hard-coding the configuration object. Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
-
Tien Hock, Loh authored
MMC stack needs OCR voltage information for the platform to initialize MMC controller correctly. Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>
-
Tien Hock, Loh authored
MMC stack needs OCR voltage information for the platform to initialize MMC controller correctly. Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>
-
- 07 Mar, 2019 3 commits
-
-
Yann Gautier authored
The change of the structure highlighted the fact that all fields are not correctly initialized with zeroes. Replace the other memset in the function with zeromem, as it is faster. Change-Id: I27f45a64e34637f79fa519f486bf5936721ef396 Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Muhammad Hadi Asyrafi Abdul Halim authored
Change map region for device 2 from non-secure to secure Signed-off-by: Muhammad Hadi Asyrafi Abdul Halim <muhammad.hadi.asyrafi.abdul.halim@intel.com>
-
Tien Hock, Loh authored
We should be using zeromem to scrub memory instead of memset. This would improve the performance by 200x Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>
-
- 04 Mar, 2019 1 commit
-
-
Marek Vasut authored
Add support for the M3W 3.0 SoC and synchronize the upstream ATF with Renesas downstream ATF release v2.0.1. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
-
- 01 Mar, 2019 2 commits
-
-
Varun Wadekar authored
This patch provides dummy macros and platform files to compile the io_storage driver backend. This patch is necessary to remove the "--unresolved=el3_panic" linker flag from Tegra's makefiles and allow us to revert this workaround, previously suggested by the ARM toolchain team. The "--unresolved=el3_panic" flag actually was a big hammer that allowed Tegra platforms to work with armlink previously but it masks legit errors with the code as well. Change-Id: I0421d35657823215229f84231896b84167f90548 Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
-
Anson Huang authored
GICR_WAKER.ProcessorSleep can only be set to zero when: — GICR_WAKER.Sleep bit[0] == 0. — GICR_WAKER.Quiescent bit[31] == 0. On some platforms, when system reboot with GIC in sleep mode but with power ON, such as on NXP's i.MX8QM, Linux kernel enters suspend but could be requested to reboot, and GIC is in sleep mode and it is inside a power domain which is ON in this scenario, when CPU reset, the GIC driver trys to set CORE's redistributor interface to awake, with GICR_WAKER.Sleep bit[0] and GICR_WAKER.Quiescent bit[31] both set, the ProcessorSleep bit[1] will never be clear and cause system hang. This patch makes sure GICR_WAKER.Sleep bit[0] and GICR_WAKER.Quiescent bit[31] are both zeor before clearing ProcessorSleep bit[1]. Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
-
- 28 Feb, 2019 4 commits
-
-
John Tsichritzis authored
Due to the shared Mbed TLS heap optimisation introduced in 6d01a463 , common code files were depending on Mbed TLS specific headers. This dependency is now removed by moving the default, unoptimised heap implementation inside the Mbed TLS specific files. Change-Id: I11ea3eb4474f0d9b6cb79a2afd73a51a4a9b8994 Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
-
Antonio Nino Diaz authored
Fix some typos and clarify some sentences. Change-Id: Id276d1ced9a991b4eddc5c47ad9a825e6b29ef74 Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
Ambroise Vincent authored
Change-Id: I7593f5ed89b9ef13b510e2259c909838c64ec56c Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
-
Chandni Cherukuri authored
Replace all uses of 'SGI_CLARK' with 'RD_N1E1_EDGE' and 'SGI_CLARK_HELIOS' with 'RD_E1_EDGE' as per the updated product names Change-Id: Ib8136e421b1a46da1e5df58c6b1432d5c78d279b Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
-
- 27 Feb, 2019 4 commits
-
-
Varun Wadekar authored
This patch provides support for using the scatterfile format as the linker script with the 'armlink' linker for Tegra platforms. In order to enable the scatterfile usage the following changes have been made: * provide mapping for ld.S symbols in bl_common.h * include bl_common.h from all the affected files * update the makefile rules to use the scatterfile and armlink to compile BL31 * update pubsub.h to add sections to the scatterfile NOTE: THIS CHANGE HAS BEEN VERIFIED WITH TEGRA PLATFORMS ONLY. Change-Id: I7bb78b991c97d74a842e5635c74cb0b18e0fce67 Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
-
Antonio Nino Diaz authored
This feature is only supported on FVP. Change-Id: I4e265610211d92a84bd2773c34acfbe02a1a1826 Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
Chandni Cherukuri authored
Replace all usage of 'sgiclark' with 'rdn1e1edge' and 'sgiclarkh' with 'rde1edge' as per the updated product names. Change-Id: I14e9b0332851798531de21d70eb54f1e5557a7bd Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
-
Chandni Cherukuri authored
Replace all usage of 'sgiclark' with 'rdn1e1edge' and 'sgiclarka' with 'rdn1edge' as per the updated product names. Change-Id: Idbc157c73477ec32f507ba2d4a4e907d8813374c Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
-
- 26 Feb, 2019 2 commits
-
-
Ying-Chun Liu (PaulLiu) authored
This commit improves the SDHost driver for RPi3 as following: * Unblock MMC_CMD(17). Using MMC_CMD(17) is more efficient on block reading. * In some low probability that SEND_OP_COND might results CRC7 error. We can consider that the command runs correctly. We don't need to retry this command so removing the code for retry. * Using MMC_BUS_WIDTH_1 as MMC default value to improve the stability. * Increase the clock to 50Mhz in data mode to speed up the io. * Change the pull resistors configuration to gain more stability. Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
-
Tien Hock, Loh authored
This adds BL31 support to Intel Stratix10 SoCFPGA platform. BL31 in TF-A supports: - PSCI calls to enable 4 CPU cores - PSCI mailbox calls for FPGA reconfiguration Signed-off-by: Loh Tien Hock <tien.hock.loh@intel.com>
-
- 22 Feb, 2019 1 commit
-
-
Chris Spencer authored
For i.MX8MQ B0 revision the default configuration of JRaMID is not valid to allow the kernel to use the CAAM job rings. This patch sets the master ID of the Cortex A in the JRaMID registers. Signed-off-by: Chris Spencer <christopher.spencer@sea.co.uk>
-
- 20 Feb, 2019 2 commits
-
-
Yann Gautier authored
STM32MP1 chip embeds a dual Cortex-A7 and a Cortex-M4. The support for Cortex-M4 clocks is added when configuring the clock tree. Some minimal security features to allow communications between A7 and M4 are also added. Change-Id: I60417e244a476f60a2758f4969700b2684056665 Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Marek Vasut authored
In case the PCIe controller receives a L1_Enter_PM DLLP, it will disable the internal PLLs. The system software cannot predict it and can attempt to perform device config space access across the PCIe link while the controller is in this transitional state. If such condition happens, the PCIe controller register access will trigger ARM64 SError exception. This patch adds checks for which PCIe controller is enabled, checks whether the PCIe controller is in such a transitional state and if so, first completes the transition and then restarts the instruction which caused the SError. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
-
- 19 Feb, 2019 4 commits
-
-
Usama Arif authored
Cortex A5 doesnt support VFP, Large Page addressing and generic timer which are addressed in this patch. The device tree for Cortex a5 is also included. Change-Id: I0722345721b145dfcc80bebd36a1afbdc44bb678 Signed-off-by: Usama Arif <usama.arif@arm.com>
-
Usama Arif authored
This patch adds support for Versatile express FVP (Fast models). Versatile express is a family of platforms that are based on ARM v7. Currently this port has only been tested on Cortex A7, although it should work with other ARM V7 cores that support LPAE, generic timers, VFP and hardware divide. Future patches will support other cores like Cortex A5 that dont support features like LPAE and hardware divide. This platform is tested on and only expected to work on single core models. Change-Id: I10893af65b8bb64da7b3bd851cab8231718e61dd Signed-off-by: Usama Arif <usama.arif@arm.com>
-
John Tsichritzis authored
Change-Id: I1adcf195c0ba739002f3a59e805c782dd292ccba Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
-
John Tsichritzis authored
Change-Id: Ideb49011da35f39ff1959be6f5015fa212ca2b6b Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
-
- 18 Feb, 2019 3 commits
-
-
Usama Arif authored
The variable is renamed to PLAT_ARM_RUN_UART as the UART is used outside BL31 as well. Change-Id: I00e3639dfb2001758b7d24548c11236c6335f64a Signed-off-by: Usama Arif <usama.arif@arm.com>
-
Samuel Holland authored
Convert them to take an mpidr instead of a (cluster, core) pair. This simplifies all of the call sites, and actually makes the functions a bit smaller. Signed-off-by: Samuel Holland <samuel@sholland.org>
-
Samuel Holland authored
This maximizes the amount of data protected by the MMU. Signed-off-by: Samuel Holland <samuel@sholland.org>
-
- 14 Feb, 2019 8 commits
-
-
Yann Gautier authored
Remove useless private structure in function prototypes. Add a reference counter on clocks. Prepare for future secured/shared/non-secured clocks. Change-Id: I3dbed81721da5ceff5e10b2c4155b1e340c036ee Signed-off-by: Yann Gautier <yann.gautier@st.com> Signed-off-by: Etienne Carriere <etienne.carriere@st.com> Signed-off-by: Lionel Debieve <lionel.debieve@st.com> Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
-
Yann Gautier authored
PWR, RCC, DDRPHYC & DDRCTRL addresses can be retrieved from device tree. Platform asserts the value read from the DT are the SoC addresses. Change-Id: I43f0890b51918a30c87ac067d3780ab27a0f59de Signed-off-by: Yann Gautier <yann.gautier@st.com> Signed-off-by: Etienne Carriere <etienne.carriere@st.com> Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
-
Yann Gautier authored
Create a new file stm32mp_clkfunc.c to put functions that could be common between several platforms. Change-Id: Ica915c796b162b2345056b33328acc05035a242c Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Yann Gautier authored
Regulator configuration at boot takes more information from DT. I2C configuration from DT is done in I2C driver. I2C driver manages more transfer modes. The min voltage of buck1 should also be increased to 1.2V, else the platform does not boot. Heavily modifies stm32_i2c.c since many functions move inside the source file to remove redundant declarations. Change-Id: I0bee5d776cf3ff15e687427cd6abc06ab237d025 Signed-off-by: Yann Gautier <yann.gautier@st.com> Signed-off-by: Etienne Carriere <etienne.carriere@st.com> Signed-off-by: Lionel Debieve <lionel.debieve@st.com> Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
-
Yann Gautier authored
timeout_init_us(some_timeout_us); returns a reference to detect timeout for the provided microsecond delay value from current time. timeout_elapsed(reference) return true/false whether the reference timeout is elapsed. This change is inspired by the OP-TEE OS timeout resources [1]. [1] https://github.com/OP-TEE/optee_os/blob/3.4.0/core/arch/arm/include/kernel/delay.h#L45 Change-Id: Id81ff48aa49693f555dc621064878417101d5587 Signed-off-by: Yann Gautier <yann.gautier@st.com> Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
-
Yann Gautier authored
Include all RCC, clocks and reset headers from stm32mp1_def.h which if exported to the firmware through platform_def.h. The same dependency removal is done in common code as well. Some useless includes are also removed in stm32_sdmmc2 driver. Change-Id: I731ea5775c3fdb7f7b0c388b93923ed5e84b8d3f Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Yann Gautier authored
Mainly remove suffix 1 from prefix stm32mp1 in several macros and functions that can be used in drivers shared by different platforms. Change-Id: I2295c44f5b1edac7e80a93c0e8dfd671b36e88e7 Signed-off-by: Yann Gautier <yann.gautier@st.com> Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
-
Yann Gautier authored
Some parts of code could be shared with platform derivatives, or new platforms. A new folder plat/st/common is created to put common parts. stm32mp_common.h is a common API aggregate. Remove some casts where applicable. Fix some types where applicable. Remove also some platform includes that are already in stm32mp1_def.h. Change-Id: I46d763c8d9e15732d1ee7383207fd58206d7f583 Signed-off-by: Yann Gautier <yann.gautier@st.com> Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
-