GitLab

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size reserved for BL2 has been increased.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The translation tables allocated for the Secure Partition do not need
to be treated as a special case. They can be put amongst the other
tables mapping BL31's general purpose memory. They will be mapped with
the same attributes as them, which is fine.

The explicit alignment constraint in BL31's linker script to pad the
last page of memory allocated to the Secure Partition's translation
tables is useless too, as page tables are per se pages, thus their
end address is naturally aligned on a page-boundary.

In fact, this patch does not change the existing behaviour. Since
patch 22282bb6

 ("SPM: Move all SP-related info to SP context
struct"), the secure_partition.c file has been renamed into sp_xlat.c
but the linker script has not been properly updated. As a result, the
SP translation tables are not specifically put at the start of the
xlat_table linker section, the __SP_IMAGE_XLAT_TABLES_START__/_END__
symbols have the same value, the size of the resulting mmap_region
covering these xlat tables is 0 and so it is ignored.

Change-Id: I4cf0a4cc090298811cca53fc9cee74df0f2b1512
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

For the BL2_AT_EL3 configuration, move BL2 higher up to make more
space for BL31.  Adjust the BL31 limit to be up to BL2 base.  This is
because BL2 is always resident for the BL2_AT_EL3 configuration and
thus we cannot overlay it with BL31.

Change-Id: I71e89863ed48f5159e8b619f49c7c73b253397aa
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

The patch changes the layout of BL images in memory to enable
more efficient use of available space. Previously BL31 was loaded
with the expectation that BL2 memory would be reclaimed by BL32
loaded in SRAM. But with increasing memory requirements in the
firmware, we can no longer fit BL32 in SRAM anymore which means the
BL2 memory is not reclaimed by any runtime image. Positioning BL2
below BL1-RW and above BL31 means that the BL31 NOBITS can be
overlaid on BL2 and BL1-RW.

This patch also propogates the same memory layout to BL32 for AArch32
mode. The reset addresses for the following configurations are also
changed :
   * When RESET_TO_SP_MIN=1 for BL32 in AArch32 mode
   * When BL2_AT_EL3=1 for BL2

The restriction on BL31 to be only in DRAM when SPM is enabled
is now removed with this change. The update to the firmware design
guide for the BL memory layout is done in the following patch.

Change-Id: Icca438e257abe3e4f5a8215f945b9c3f9fbf29c9
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

BL31 is running out of space, and the use-case of SPM doesn't require it
to be in SRAM. To prevent BL31 from running out of space in the future,
move BL31 to DRAM if SPM is enabled.

Secure Partition Manager design document updated to reflect the changes.

Increased the size of the stack of BL31 for builds with SPM.

The translation tables used by SPM in Arm platforms have been moved back
to the 'xlat_tables' region instead of 'arm_el3_tzc_dram'. Everything is
in DRAM now, so it doesn't make sense to treat them in a different way.

Change-Id: Ia6136c8e108b8da9edd90e9d72763dada5e5e5dc
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.

The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.

Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.

The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.

Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This reverts commit 2f18aa1f

.

It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.

Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I7e73c0ab134da11c49f990b739245110c59eac2b
Signed-off-by: Chris Kay <chris.kay@arm.com>

SGI-575's NSRAM is neither in the same place nor the same size as Juno's.

Change-Id: Id6d692e9c7e9c1360014bb525eda966ebe29c823
Signed-off-by: Chris Kay <chris.kay@arm.com>

The bounds check in ARM_CASSERT_MMAP does not take into account the
array sentinel in plat_arm_mmap. This commit fixes this, and adds an
additional check to ensure the number of entries in the array is
within the bounds of PLAT_ARM_MMAP_ENTRIES.

Change-Id: Ie6df10c0aa0890d62826bc3224ad7b3e36fd53e2
Signed-off-by: Chris Kay <chris.kay@arm.com>

There are three calls to mmap_add_region() that always occur in
arm_setup_page_tables(), and two further calls based on whether coherent
memory is enabled, and whether SPM is enabled in BL31.

This commit adapts the ARM_BL_REGIONS definition to match the number of
calls made inside arm_setup_page_tables() so that the MAX_MMAP_REGIONS
is realigned with what is actually occurring.

Change-Id: I7adc05951abccf2cbd5c86280eb874911e6a1566
Signed-off-by: Chris Kay <chris.kay@arm.com>

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size of BL31 has been increased in builds with SPM.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

  - Assign 0x10 for RAS exceptions on ARM platforms, and install
    EHF priority descriptor.

  - Call the common RAS initialisation from ARM BL31 setup.

  - Add empty definitions for platform error records and RAS interrupts.

Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

At present, any External Abort routed to EL3 is reported as an unhandled
exception and cause a panic. This patch enables ARM Trusted Firmware to
handle External Aborts routed to EL3.

With this patch, when an External Abort is received at EL3, its handling
is delegated to plat_ea_handler() function. Platforms can provide their
own implementation of this function. This patch adds a weak definition
of the said function that prints out a message and just panics.

In order to support handling External Aborts at EL3, the build option
HANDLE_EA_EL3_FIRST must be set to 1.

Before this patch, HANDLE_EA_EL3_FIRST wasn't passed down to
compilation; this patch fixes that too.

Change-Id: I4d07b7e65eb191ff72d63b909ae9512478cd01a1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.

The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.

Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.

This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>

In some use-cases BL2 will be stored in eXecute In Place (XIP) memory,
like BL1. In these use-cases, it is necessary to initialize the RW sections
in RAM, while leaving the RO sections in place. This patch enable this
use-case with a new build option, BL2_IN_XIP_MEM. For now, this option
is only supported when BL2_AT_EL3 is 1.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>

Void pointers have been used to access linker symbols, by declaring an
extern pointer, then taking the address of it. This limits symbols
values to aligned pointer values. To remove this restriction an
IMPORT_SYM macro has been introduced, which declares it as a char
pointer and casts it to the required type.

Change-Id: I89877fc3b13ed311817bb8ba79d4872b89bfd3b0
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>

This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.

The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.

Fixes ARM-software/tf-issues#559

Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=juno LOG_LEVEL=50 all

Change-Id: Ic8f611da734f356566e8208053296e6c62b54709
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.3: All declarations of an object or function shall
          use the same names and type qualifiers.

Fixed for:

	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I48201c9ef022f6bd42ea8644529afce70f9b3f22
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined.

Change-Id: I26e042cb251a6f9590afa1340fdac73e42f23979
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.3: All declarations of an object or function shall
          use the same names and type qualifiers.

Change-Id: Iff384187c74a598a4e73f350a1893b60e9d16cec
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

MISRA C-2012 Rule 7.3 violation: lowercase l shall not be used as literal suffixes.

This patch resolves this for the ULL() macro by using ULL suffix instead
of the ull suffix.

Change-Id: Ia8183c399e74677e676956e8653e82375d0e0a01
Signed-off-by: David Cunado <david.cunado@arm.com>

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.

Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The `bl1_init_bl2_mem_layout()` API is now deprecated. The default weak
implementation of `bl1_plat_handle_post_image_load()` calculates the
BL2 memory layout and populates the same in x1(r1). This ensures
compatibility for the deprecated API.

Change-Id: Id44bdc1f572dc42ee6ceef4036b3a46803689315
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.

Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch introduces a new BL handover interface. It essentially allows
passing 4 arguments between the different BL stages. Effort has been made
so as to be compatible with the previous handover interface. The previous
blx_early_platform_setup() platform API is now deprecated and the new
blx_early_platform_setup2() variant is introduced. The weak compatiblity
implementation for the new API is done in the `plat_bl_common.c` file.
Some of the new arguments in the new API will be reserved for generic
code use when dynamic configuration support is implemented. Otherwise
the other registers are available for platform use.

Change-Id: Ifddfe2ea8e32497fe1beb565cac155ad9d50d404
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds an argument to bl1_plat_post/pre_image_load() APIs
to make it more future proof. The default implementation of
these are moved to `plat_bl1_common.c` file.

These APIs are now invoked appropriately in the FWU code path prior
to or post image loading by BL1 and are not restricted
to LOAD_IMAGE_V2.

The patch also reorganizes some common platform files. The previous
`plat_bl2_el3_common.c` and `platform_helpers_default.c` files are
merged into a new `plat_bl_common.c` file.

NOTE: The addition of an argument to the above mentioned platform APIs
is not expected to have a great impact because these APIs were only
recently added and are unlikely to be used.

Change-Id: I0519caaee0f774dd33638ff63a2e597ea178c453
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Just like bl2_, add pre/post image load handlers for BL1.  No argument
is needed since BL2 is the only image loaded by BL1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

There are cases where we need to manipulate image information before
the load.  For example, for decompressing data, we cannot load the
compressed images to their final destination.  Instead, we need to
load them to the temporary buffer for the decompressor.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.

The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:

	--data cluster0.cpu0=bl2.bin@0x4001000
	-C cluster0.cpu0.RVBAR=0x4001000

These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.

Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch enables BL2 to execute at the highest exception level
without any dependancy on TF BL1. This enables platforms which already
have a non-TF Boot ROM to directly load and execute BL2 and subsequent BL
stages without need for BL1.  This is not currently possible because
BL2 executes at S-EL1 and cannot jump straight to EL3.

Change-Id: Ief1efca4598560b1b8c8e61fbe26d1f44e929d69
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

On some build configurations BL31 is running out of space.  Now that
TSP is moved to secure dram, we have a bit of additional space to use
in BL31.

Change-Id: Ib89fcd8bae99c85c9c5e5d9228bb42fb7048dcb6
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Signed-off-by: David Cunado <david.cunado@arm.com>

To allow BL31 to grow in SRAM, move TSP in TZC secured DRAM
by default.

Increase the BL31 max limit by one page.

Change-Id: Idd3479be02f0f9bafac2f275376d7db0c2015431
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.

Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

A new platform define, `PLAT_SP_IMAGE_XLAT_SECTION_NAME`, has been
introduced to select the section where the translation tables used by
the S-EL1/S-EL0 are placed.

This define has been used to move the translation tables to DRAM secured
by TrustZone.

Most of the extra needed space in BL31 when SPM is enabled is due to the
large size of the translation tables. By moving them to this memory
region we can save 44 KiB.

A new argument has been added to REGISTER_XLAT_CONTEXT2() to specify the
region where the translation tables have to be placed by the linker.

Change-Id: Ia81709b4227cb8c92601f0caf258f624c0467719
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>