GitLab

By default the SMMU for the DMA-330 is configured to mark some stream IDs
as always belonging to the Secure world. As a result, if EL1 software turns
the SMMU on, certain Non-Secure accesses get rewritten as Secure, making
them bypass translation and access Secure physical addresses directly.

Since the current Juno board firmware configures the DMA-330 hardware as
Non-Secure, rewrite the SMMU's default SSD table as well to prevent any
unexpected behaviour in EL1.

Change-Id: Iaa81d883eecf28d80eb182b9ce475684bf9c718c

This patch defines MAX_MMAP_REGIONS separately for each BL stage
as per its requirements. This minimizes the size of the mmap[]
array.

Fixes ARM-Software/tf-issues#201

Change-Id: I19b15e1a91a8365b2ecf24e2cd71937cb73916b2

This patch adds support to authenticate the Trusted Key certificate
and the BL3-x certificates and images at BL2.

Change-Id: I69a8c13a14c8da8b75f93097d3a4576aed71c5dd

This patch moves fvp_io_setup() to bl2_early_platform_setup() in order
to allow BL2 to use the IO framework before bl2_platform_setup().

Change-Id: I75e1a772ab5f9b4727f6727822a2527c30f3c63d

This patch adds support to authenticate the BL2 content certificate
and image using the authentication module in BL1.

The FIP driver has been extended to include the BL2 certificate
UUID.

FVP and Juno ports include the BL2 certificate FIP file
definition.

Change-Id: I32680e9bd123c8db4a4193c14448c9b32b0e9325

This patch implements an authentication module based on the
PolarSSL library (v1.3.9) to verify the Chain of Trust when
Trusted Boot is enabled.

PolarSSL sources must be fetched separately. The POLARSSL_DIR
build option may be used to indicate the path to the PolarSSL
main directory (this directory must contain the 'include' and
'library' subdirectories).

To be able to build PolarSSL sources as a part of the Trusted
Firmware build process, the DISABLE_PEDANTIC flag in polarssl.mk
will tell the build system to remove the -pedantic option from
the CFLAGS.

Inclusion of PolarSSL increases the memory requirements of the BL1
and BL2 images. The following are the changes made to the FVP and
Juno platforms to cater for this when TRUSTED_BOARD_BOOT is
defined:

Changes on FVP:

  - BL1 and BL2 stacks have been increased to 4 KB
  - BL1(rw) section has been increased to 32 KB.
  - BL2 memory region has been increased to 112 KB

Changes on Juno:

  - BL1 and BL2 stacks have been increased to 4 KB
  - BL1(rw) section has been increased to 32 KB.
  - Trusted ROM region in Flash has been increased to 128 KB.
  - BL2 memory region has been increased to 116 KB

Change-Id: Ie87d80d43408eb6239c4acd0ec5ab2120e4e9e80

This patch adds the function plat_match_rotpk() to the platform
porting layer to provide a Root Of Trust Public key (ROTPK)
verification mechanism. This function is called during the
Trusted Board Boot process and receives a supposed valid copy
of the ROTPK as a parameter, usually obtained from an external
source (for instance, a certificate). It returns 0 (success) if
that key matches the actual ROTPK stored in the system or any
other value otherwise.

The mechanism to access the actual ROTPK stored in the system
is platform specific and should be implemented as part of this
function. The format of the ROTPK is also platform specific
(to save memory, some platforms might store a hash of the key
instead of the whole key).

TRUSTED_BOARD_BOOT build option has been added to allow the user
to enable the Trusted Board Boot features. The implementation of
the plat_match_rotpk() funtion is mandatory when Trusted Board
Boot is enabled.

For development purposes, FVP and Juno ports provide a dummy
function that returns always success (valid key). A safe trusted
boot implementation should provide a proper matching function.

Documentation updated accordingly.

Change-Id: I74ff12bc2b041556c48533375527d9e8c035b8c3

This patch adds a tool that generates all the necessary elements
to establish the chain of trust (CoT) between the images.

The tool reads the binary images and signing keys and outputs the
corresponding certificates that will be used by the target at run
time to verify the authenticity of the images.

Note: the platform port must provide the file platform_oid.h. This
file will define the OIDs of the x509 extensions that will be added
to the certificates in order to establish the CoT.

Change-Id: I2734d6808b964a2107ab3a4805110698066a04be

This patch adds support to call the reset_handler() function in BL3-1 in the
cold and warm boot paths when another Boot ROM reset_handler() has already run.

This means the BL1 and BL3-1 versions of the CPU and platform specific reset
handlers may execute different code to each other. This enables a developer to
perform additional actions or undo actions already performed during the first
call of the reset handlers e.g. apply additional errata workarounds.

Typically, the reset handler will be first called from the BL1 Boot ROM. Any
additional functionality can be added to the reset handler when it is called
from BL3-1 resident in RW memory. The constant FIRST_RESET_HANDLER_CALL is used
to identify whether this is the first version of the reset handler code to be
executed or an overridden version of the code.

The Cortex-A57 errata workarounds are applied only if they have not already been
applied.

Fixes ARM-software/tf-issue#275

Change-Id: Id295f106e4fda23d6736debdade2ac7f2a9a9053

This patch allows the secure payload (BL3-2) to be loaded in the
DRAM region secured by the TrustZone controller (top 16 MB of DRAM1).

The location of BL3-2 can be selected at build time by setting the
build flag FVP_TSP_RAM_LOCATION to one of the following options:

  - 'tsram' : Trusted SRAM (this is the default option)
  - 'tdram' : Trusted DRAM
  - 'dram'  : Secure region in DRAM1 (top 16MB configured by the
              TrustZone controller)

The number of MMU tables in BL3-2 depends on its location in
memory: 3 in case it is loaded in DRAM, 2 otherwise.

Documentation updated accordingly.

Fixes ARM-software/tf-issues#212

Change-Id: I371eef3a4159f06a0c9e3c6c1f4c905b2f93803a

This patch allows the platform to validate the power_state and
entrypoint information from the normal world early on in PSCI
calls so that we can return the error safely. New optional
pm_ops hooks `validate_power_state` and `validate_ns_entrypoint`
are introduced to do this.

As a result of these changes, all the other pm_ops handlers except
the PSCI_ON handler are expected to be successful. Also, the PSCI
implementation will now assert if a PSCI API is invoked without the
corresponding pm_ops handler being registered by the platform.

NOTE : PLATFORM PORTS WILL BREAK ON MERGE OF THIS COMMIT. The
pm hooks have 2 additional optional callbacks and the return type
of the other hooks have changed.

Fixes ARM-Software/tf-issues#229

Change-Id: I036bc0cff2349187c7b8b687b9ee0620aa7e24dc

This patch removes the non-secure entry point information being passed
to the platform pm_ops which is not needed. Also, it removes the `mpidr`
parameter for  platform pm hooks which are meant to do power management
operations only on the current cpu.

NOTE: PLATFORM PORTS MUST BE UPDATED AFTER MERGING THIS COMMIT.

Change-Id: If632376a990b7f3b355f910e78771884bf6b12e7

This patch extends the build option `USE_COHERENT_MEMORY` to
conditionally remove coherent memory from the memory maps of
all boot loader stages. The patch also adds necessary
documentation for coherent memory removal in firmware-design,
porting and user guides.

Fixes ARM-Software/tf-issues#106

Change-Id: I260e8768c6a5c2efc402f5804a80657d8ce38773

This patch moves the bakery locks out of coherent memory to normal memory.
This implies that the lock information needs to be placed on a separate cache
line for each cpu. Hence the bakery_lock_info_t structure is allocated in the
per-cpu data so as to minimize memory wastage. A similar platform per-cpu
data is introduced for the platform locks.

As a result of the above changes, the bakery lock api is completely changed.
Earlier, a reference to the lock structure was passed to the lock implementation.
Now a unique-id (essentially an index into the per-cpu data array) and an offset
into the per-cpu data for bakery_info_t needs to be passed to the lock
implementation.

Change-Id: I1e76216277448713c6c98b4c2de4fb54198b39e0

This patch maps the non-secure region of DRAM1 in the MMU. The
non-secure region comprises the whole DRAM1 (0x80000000 -
0xffffffff) excluding the top 16 MB (0xff000000 - 0xffffffff).
The TrustZone controller configures this 16 MB region as secure
memory, so it can not be accessed in non-secure mode.

The number of MMU tables in BL2 has been increased to 3 because
the new size of the non-secure region in DRAM requires an extra L2
table.

Change-Id: I5ad080c6e181f6b6060e15cebb1d18b7fa128cf5

This patch allows the BL3-1 NOBITS section to overlap the BL1 R/W
section since the former will always be used after the latter.
Similarly, the BL3-2 NOBITS section can overlay the BL2 image
when BL3-2 is loaded in Trusted SRAM.

Due to the current size of the images, there is no actual overlap.
Nevertheless, this reorganization may help to optimise the Trusted
SRAM usage when the images size grows.

Note that because BL3-1 NOBITS section is allowed to overlap the
BL1 R/W section, BL1 global variables will remain valid only until
execution reaches the BL3-1 entry point during a cold boot.

Documentation updated accordingly.

Fixes ARM-software/tf-issues#254

Change-Id: Id538f4d1c7f1f7858108280fd7b97e138572b879

In both FVP and Juno ports, IRQ #16, which is a PPI, is incorrectly
identified as secure SGI #8 through the constant IRQ_SEC_SGI_8.
This patch removes it.

Fixes ARM-software/tf-issues#282

Change-Id: I9e52d849611ffcd2b1f28e56dd156c5b217ed63e

This patch reassigns the crash console on Juno and FVP to use the runtime
BL3-1 console. The crash console is changed to SoC UART0 (UART2) from the
previous FPGA UART0 (UART0) on Juno. In FVP, it is changed from UART0 to
UART1.

Fixes ARM-software/tf-issues#256

Change-Id: I7df54f86ca00ec2652c27261dd66a94c12610816

This patch replaces the usage of the GIC private driver in Juno with
the generic ARM GIC driver. The private driver is no longer necessary
and has been removed from the Juno port.

Fixes ARM-software/tf-issues#253

Change-Id: I6aaabc252e5e6fb5fcf44ab6d0febd9b38791056

This patch optimizes the Cortex-A57 cluster power down sequence by not
flushing the Level1 data cache. The L1 data cache and the L2 unified
cache are inclusive. A flush of the L2 by set/way flushes any dirty
lines from the L1 as well. This is a known safe deviation from the
Cortex-A57 TRM defined power down sequence. This optimization can be
enabled by the platform through the 'SKIP_A57_L1_FLUSH_PWR_DWN' build
flag. Each Cortex-A57 based platform must make its own decision on
whether to use the optimization.

This patch also renames the cpu-errata-workarounds.md to
cpu-specific-build-macros.md as this facilitates documentation
of both CPU Specific errata and CPU Specific Optimization
build macros.

Change-Id: I299b9fe79e9a7e08e8a0dffb7d345f9a00a71480

This patch deprecates the build option to relocate the shared data
into Trusted DRAM in FVP. After this change, shared data is always
located at the base of Trusted SRAM. This reduces the complexity
of the memory map and the number of combinations in the build
options.

Fixes ARM-software/tf-issues#257

Change-Id: I68426472567b9d8c6d22d8884cb816f6b61bcbd3

This patch adds support on the Juno platform for entering a wfi in
response to a PSCI CPU_SUSPEND call where the state type is a
standby state.

Change-Id: I0a102dee1f8d2ad936c63ad1d1d3ad001a4a4768

This patch configures the TrustZone Controller in Juno to split
the 2GB DDR-DRAM memory at 0x80000000 into Secure and Non-Secure
regions:

- Secure DDR-DRAM: top 16 MB, except for the last 2 MB which are
  used by the SCP for DDR retraining
- Non-Secure DDR-DRAM: remaining DRAM starting at base address

Build option PLAT_TSP_LOCATION selects the location of the secure
payload (BL3-2):

- 'tsram' : Trusted SRAM (default option)
- 'dram'  : Secure region in the DDR-DRAM (set by the TrustZone
            controller)

The MMU memory map has been updated to give BL2 permission to load
BL3-2 into the DDR-DRAM secure region.

Fixes ARM-software/tf-issues#233

Change-Id: I6843fc32ef90aadd3ea6ac4c7f314f8ecbd5d07b

This patch replaces direct accesses to the TZC-400 registers by the
appropiate calls to the generic driver available in the Trusted
Firmware in order to initialize the TrustZone Controller.

Functions related to the initialization of the secure memory,
like the TZC-400 configuration, have been moved to a new file
'plat_security.c'. This reorganization makes easier to set up
the secure memory from any BL stage.

TZC-400 initialization has been moved from BL1 to BL2 because BL1
does not access the non-secure memory. It is BL2's responsibility
to enable and configure the TZC-400 before loading the next BL
images.

In Juno, BL3-0 initializes some of the platform peripherals, like
the DDR controller. Thus, BL3-0 must be loaded before configuring
the TrustZone Controller. As a consequence, the IO layer
initialization has been moved to early platform initialization.

Fixes ARM-software/tf-issues#234

Change-Id: I83dde778f937ac8d2996f7377e871a2e77d9490e

This patch uses the IMAGE_BL<x> constants to create translation tables specific
to a boot loader stage. This allows each stage to create mappings only for areas
in the memory map that it needs.

Fixes ARM-software/tf-issues#209

Change-Id: Ie4861407ddf9317f0fb890fc7575eaa88d0de51c

This patch avoids the problem of crash reporting mechanism accessing
global data in BSS by 'plat_print_gic_regs' for FVP platforms. Earlier
it depended on the global 'plat_config' object for the GIC Base address
in FVP platforms which would have caused exception if it were accessed
before the BSS was initialized. It is now fixed by dynamically
querying the V2M_SYS_ID to find the FVP model type and accordingly
selecting the appropriate GIC Base address.

This patch also fixes the 'plat_print_gic_regs' to use the correct GIC
Distributor base address for printing GICD_IS_PENDR register values
for both Juno and FVP platforms.

Fixes ARM-Software/tf-issues#236

Change-Id: I545c7b908b3111419bf27db0575ce86acf86784b

This patch gathers miscellaneous minor fixes to the documentation, and comments
in the source code.

Change-Id: I631e3dda5abafa2d90f464edaee069a1e58b751b
Co-Authored-By: Soby Mathew <soby.mathew@arm.com>
Co-Authored-By: Dan Handley <dan.handley@arm.com>

This patch changes the UART port assignment for various BL stages
so as to make it consistent on the platform ports. The BL1, BL2 and
BL3-1 now uses UART0 on the FVP port and SoC UART0 on the Juno port.
The BL3-2 uses UART2 on the FVP port and FPGA UART0 on the Juno
port.

This provides an interim fix to ARM-software/tf-issues#220 until
support is added for changing the UART port for a BL image between
cold boot and runtime.

Change-Id: Iae5faea90be3d59e41e597b34a902f93e737505a

This patch removes the PRIMARY_CPU definition hardcoded in the
Juno port. Instead, the primary CPU is obtained at runtime by
reading the SCC General Purpose Register 1 (GPR_1), whose value
is copied by the SCP into shared memory during the boot process.

Change-Id: I3981daa92eb7142250712274cf7f655b219837f5

This patch adds the Juno platform specific handlers for PSCI
SYSTEM_OFF and SYSTEM_RESET operations.

Change-Id: Ie389adead533ec2314af44d721b4d0f306147c7d

This patch implements the TSP on Juno. It executes from on-chip Trusted
SRAM.

Also, the other bootloader images (i.e. BL1 R/W, BL2 and BL3-1) have
been moved around. The reason is, although there was enough space
overall to store the TSP in SRAM, there was no contiguous free chunk
of SRAM big enough to hold it.

This patch keeps the overall memory layout (i.e. keeping BL1 R/W at
the bottom, BL2 at the top and BL3-1 in between) but moves the base
addresses of all the bootloader images in such a way that:
 - memory fragmentation is reduced enough to fit BL3-2 in;
 - new base addresses are suitable for release builds as well as debug
   ones;
 - each image has a few extra kilobytes for future growth.
   BL3-1 and BL3-2 are the images which received the biggest allocations
   since they will most probably grow the most.

This patch also adds instruction synchronization barriers around the code which
handles the timer interrupt in the TSP. This ensures that the interrupt is not
acknowledged after or EOIed before it is deactivated at the peripheral.

Change-Id: I1c5b51858700027ee283ac85d18e06863a27c72e

This patch adds support for PSCI CPU_OFF and CPU_SUSPEND APIs to the Juno port
of the ARM Trusted Firmware. The maximum affinity level that can be suspended is
the cluster level (affinity level 1). Support for suspending the system level is
not present.

Change-Id: Ie2c9da0acd7d1b0d5ac64940cdf40347153e52c8

This patch adds the initial port of the ARM Trusted Firmware on the Juno
development platform. This port does not support a BL3-2 image or any PSCI APIs
apart from PSCI_VERSION and PSCI_CPU_ON. It enables workarounds for selected
Cortex-A57 (#806969 & #813420) errata and implements the workaround for a Juno
platform errata (Defect id 831273).

Change-Id: Ib3d92df3af53820cfbb2977582ed0d7abf6ef893

This patch adds CPU core and cluster power down sequences to the CPU specific
operations framework introduced in a earlier patch. Cortex-A53, Cortex-A57 and
generic AEM sequences have been added. The latter is suitable for the
Foundation and Base AEM FVPs. A pointer to each CPU's operations structure is
saved in the per-cpu data so that it can be easily accessed during power down
seqeunces.

An optional platform API has been introduced to allow a platform to disable the
Accelerator Coherency Port (ACP) during a cluster power down sequence. The weak
definition of this function (plat_disable_acp()) does not take any action. It
should be overriden with a strong definition if the ACP is present on a
platform.

Change-Id: I8d09bd40d2f528a28d2d3f19b77101178778685d

This patch adds an optional platform API (plat_reset_handler) which allows the
platform to perform any actions immediately after a cold or warm reset
e.g. implement errata workarounds. The function is called with MMU and caches
turned off. This API is weakly defined and does nothing by default but can be
overriden by a platform with a strong definition.

Change-Id: Ib0acdccbd24bc756528a8bd647df21e8d59707ff

This patch introduces a framework which will allow CPUs to perform
implementation defined actions after a CPU reset, during a CPU or cluster power
down, and when a crash occurs. CPU specific reset handlers have been implemented
in this patch. Other handlers will be implemented in subsequent patches.

Also moved cpu_helpers.S to the new directory lib/cpus/aarch64/.

Change-Id: I1ca1bade4d101d11a898fb30fea2669f9b37b956

This patch provides a workaround for the ASM_ASSERT label issue
and also reworks the use of labels in assembly macros.
If the caller of the ASM_ASSERT macro happened to use the
label '1' to jump past the ASM_ASSERT macro, it would not have
worked since the ASM_ASSERT macro internally used the same label.
Hence, as a workaround, this patch makes the label a high
number in the expectation that the caller will never use it.

Also updated the other assembly macros using numerical labels to
named lables.

Change-Id: Iec892359db84f2391ad2a83a92141c4d7049776a

This patch reworks FVP port's power management implementation to perform
platform actions only when the platform exported hook is invoked for the highest
affinity level to enter/exit the OFF state.

For example, during a CPU_OFF operation, fvp_affinst_off() is called twice: for
affinity level 0 and affinity level 1 (in that order). CPU specific operations
are deferred until the next invocation if it is determined through a call to
psci_get_max_phys_off_afflvl() that this is CPU is the last in the cluster.

Similarly, during power up if the CPU is the first in the cluster, both CPU and
cluster specific operations are performed when fvp_affinst_on_finish() is
invoked for affinity level 1. Earlier, they were done across the two invocations
of the handler.

Change-Id: I4288ed3ba1385db36a69cc2e598deb219f209b8a

This patch adds support for SYSTEM_OFF and SYSTEM_RESET PSCI
operations. A platform should export handlers to complete the
requested operation. The FVP port exports fvp_system_off() and
fvp_system_reset() as an example.

If the SPD provides a power management hook for system off and
system reset, then the SPD is notified about the corresponding
operation so it can do some bookkeeping. The TSPD exports
tspd_system_off() and tspd_system_reset() for that purpose.

Versatile Express shutdown and reset methods have been removed
from the FDT as new PSCI sys_poweroff and sys_reset services
have been added. For those kernels that do not support yet these
PSCI services (i.e. GICv3 kernel), the original dtsi files have
been renamed to *-no_psci.dtsi.

Fixes ARM-software/tf-issues#218

Change-Id: Ic8a3bf801db979099ab7029162af041c4e8330c8

* Move TSP platform porting functions to new file:
  include/bl32/tsp/platform_tsp.h.

* Create new TSP_IRQ_SEC_PHY_TIMER definition for use by the generic
  TSP interrupt handling code, instead of depending on the FVP
  specific definition IRQ_SEC_PHY_TIMER.

* Rename TSP platform porting functions from bl32_* to tsp_*, and
  definitions from BL32_* to TSP_*.

* Update generic TSP code to use new platform porting function names
  and definitions.

* Update FVP port accordingly and move all TSP source files to:
  plat/fvp/tsp/.

* Update porting guide with above changes.

Note: THIS CHANGE REQUIRES ALL PLATFORM PORTS OF THE TSP TO
      BE UPDATED

Fixes ARM-software/tf-issues#167

Change-Id: Ic0ff8caf72aebb378d378193d2f017599fc6b78f