GitLab

Whenever the VPR memory is resized, the GPU is put into reset first
and then the new VPR parameters are programmed to the memory controller
block. There exists a scenario, where the GPU might be out before we
program the new VPR parameters. This means, the GPU would still be
using older settings and leak secrets.

This patch puts the GPU back into reset, if it is out of reset after
resizing VPR, to mitigate this hole.

Change-Id: I38a1000e3803f80909efcb02e27da4bd46909931
Signed-off-by: Jeetesh Burman <jburman@nvidia.com>

This patch cleans the Memory controller's interrupt status
register, before exiting to the non-secure world during
cold boot. This is required as we observed that the MC's
arbitration bit is set before exiting the secure world.

Change-Id: Iacd01994d03b3b9cbd7b8a57fe7ab5b04e607a9f
Signed-off-by: Harvey Hsieh <hhsieh@nvidia.com>

If ECID is valid, we can use force instantiation
otherwise, we should use reseed for random data
generation for RNG operations in SE context save
DNI because we are not keeping software save
sequence in main.

Change-Id: I73d650e6f45db17b780834b8de4c10501e05c8f3
Signed-off-by: Samuel Payne <spayne@nvidia.com>

This change ports the software based SE context save routines.
The software implements the context save sequence for SE/SE2 and
PKA1. The context save routine is intended to be invoked from
the ATF SC7 entry.

Change-Id: I9aa156d6e7e22a394bb10cb0c3b05fc303f08807
Signed-off-by: Marvin Hsu <marvinh@nvidia.com>

MISRA Rule 10.3, the value of an expression shall not be assigned to
an object with a narrower essential type or of a different essential
type category.

The essential type of a enum member is anonymous enum, the enum member
should be casted to the right type when using it.

Both UL and ULL suffix equal to uint64_t constant in compiler
aarch64-linux-gnu-gcc, to avoid confusing, only keep U and ULL suffix
in platform code. So in some case, cast a constant to uint32_t is
necessary.

Change-Id: I1aae8cba81ef47481736e7f95f53570de7013187
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>

This patch enables clocks to the SE and Entropy block and gets them
out of reset, before starting the context save operation.

Change-Id: Ic196be8fb833dfd04c0e8d460c07058429999613
Signed-off-by: Samuel Payne <spayne@nvidia.com>

This patch disables SMMU hardware before suspending the SE
block, for the context save operation to complete. The NS
word will re-enable SMMU when we exit System Suspend.

Change-Id: I4d5cd982ea6780db5c38b124550d847e3928c60d
Signed-off-by: Samuel Payne <spayne@nvidia.com>

This patch memmaps all the IRAM memory banks during boot. The BPMP
firmware might place the channels in any of the IRAMs, so it is better
to map all the banks to avoid surprises.

Change-Id: Ia009a65d227ee50fbb23e511ce509daf41b877ee
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds the driver to communicate with the BPMP processor
for power management use cases. BPMP controls the entry into cluster
and system power states. The Tegra210 platform port queries the BPMP
to calculate the target state for the cluster. In case BPMP does not
allow CCx entry, the core enters a power down state.

Change-Id: I9c40aef561607a0b02c49b7f8118570eb9105cc9
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds the implementation of the SE atomic context save
sequence. The atomic context-save consistently saves to the TZRAM
carveout; thus there is no need to declare context save buffer or
map MMU region in TZRAM for context save. The atomic context-save
routine is responsible to validate the context-save progress
counter, where CTX_SAVE_CNT=133(SE1)/646(SE2), and the SE error
status to ensure the context save procedure complete successfully.

Change-Id: Ic80843902af70e76415530266cb158f668976c42
Signed-off-by: Marvin Hsu <marvinh@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch moves the GPU reset state check, during VideoMem resize, to the
common SiP handler, to reduce code duplication.

Change-Id: I3818c5f104b809da83dc2a61d6a8149606f81c13
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds explicit casts (U(x)) to integers in the tegra_def.h
headers, to make them compatible with whatever operation they're used
in [MISRA-C Rule 10.1]

Change-Id: Ic5fc611aad986a2c6e6e6f625e0753ab9b69eb02
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

For SoCs T132 and T210, the header file 'platform_def.h' used to include
'tegra_def.h' and vice versa. This patch breaks this circular dependency
by making 'tegra_def.h' independent.

Change-Id: I45a00a84e6ab8b93d5e9242a9ff65f03e9102a96
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch adds the Tegra micro-seconds controller to the
memory map. This allows us to use the delay_timer functionality.

Change-Id: Ia8b148a871949bfede539974cacbe0e93ec7e77c
Signed-off-by: Steven Kao <skao@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch moves the chip specific memory controller driver defines to
the appropriate tegra_def.h files, for future compatibility.

Change-Id: I3179fb771d8b32e913ca29bd94af95f4b2fc1961
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support to identify the underlying platform
on which we are running. The currently supported platforms
are actual silicon and simulation platforms.

Change-Id: Iadf96e79ec663b3dbd1a18e9bb95ffcdb82fc8af
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch modifies the secure IRQ registration process to allow platforms
to specify the target CPUs as well as the owner of the IRQ. IRQs "owned"
by the EL3 would return INTR_TYPE_EL3 whereas those owned by the Trusted
OS would return INTR_TYPE_S_EL1 as a result.

Change-Id: I528f7c8220d0ae0c0f354e78d69e188abb666ef6
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Tegra chips support multiple FIQ interrupt sources. These interrupts
are enabled in the GICD/GICC interfaces by the tegra_gic driver. A
new FIQ handler would be added in a subsequent change which can be
registered by the platform code.

This patch adds the GIC programming as part of the tegra_gic_setup()
which now takes an array of all the FIQ interrupts to be enabled for
the platform. The Tegra132 and Tegra210 platforms right now do not
register for any FIQ interrupts themselves, but will definitely use
this support in the future.

Change-Id: I0ea164be901cd6681167028fea0567399f18d4b8
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The platform power states, PLAT_MAX_RET_STATE and PLAT_MAX_OFF_STATE,
can change on Tegra SoCs and so should be defined per-soc.

This patch moves these macro definitions to individual SoC's tegra_def.h
files.

Change-Id: Ib9b2752bc4d79cef6f79bee49882d340f71977a2
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch introduces a function to secure the on-chip TZRAM memory. The
Tegra132 and Tegra210 chips do not have a compelling use case to lock the
TZRAM. The trusted OS owns the TZRAM aperture on these chips and so it
can take care of locking the aperture. This might not be true for future
chips and this patch makes the TZRAM programming flexible.

Change-Id: I3ac9f1de1b792ccd23d4ded274784bbab2ea224a
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The BL2 fills in the UART controller ID to be used as the normal as
well as the crash console on Tegra platforms. The controller ID to
UART controller base address mapping is handled by each Tegra SoC
the base addresses might change across Tegra chips.

This patch adds the handler to parse the platform params to get the
UART ID for the per-soc handlers.

Change-Id: I4d167b20a59aaf52a31e2a8edf94d8d6f89598fa
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch enables the processor retention and L2/CPUECTLR read/write
access from the NS world only for Cortex-A57 CPUs on the Tegra SoCs.

Change-Id: I9941a67686ea149cb95d80716fa1d03645325445
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The Memory Select Switch Controller routes any CPU transactions to
the appropriate slave depending on the transaction address. During
system suspend, it loses all config settings and hence the CPU has
to restore them during resume.

This patch restores the controller's settings for enabling WRAP to
INCR burst type conversions on the master ports, for any incoming
requests from the AXI slave ports.

Tested by performing multiple system suspend cycles.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch implements the get_sys_suspend_power_state() handler required by
the PSCI SYSTEM_SUSPEND API. The intent of this handler is to return the
appropriate State-ID field which can be utilized in `affinst_suspend()` to
suspend to system affinity level.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

T210 is the latest chip in the Tegra family of SoCs from NVIDIA. It is an
ARM v8 dual-cluster (A57/A53) SoC, with any one of the clusters being active
at a given point in time.

This patch adds support to boot the Trusted Firmware on T210 SoCs. The patch
also adds support to boot secondary CPUs, enter/exit core power states for
all CPUs in the slow/fast clusters. The support to switch between clusters
is still not available in this patch and would be available later.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch implements the TSP on Juno. It executes from on-chip Trusted
SRAM.

Also, the other bootloader images (i.e. BL1 R/W, BL2 and BL3-1) have
been moved around. The reason is, although there was enough space
overall to store the TSP in SRAM, there was no contiguous free chunk
of SRAM big enough to hold it.

This patch keeps the overall memory layout (i.e. keeping BL1 R/W at
the bottom, BL2 at the top and BL3-1 in between) but moves the base
addresses of all the bootloader images in such a way that:
 - memory fragmentation is reduced enough to fit BL3-2 in;
 - new base addresses are suitable for release builds as well as debug
   ones;
 - each image has a few extra kilobytes for future growth.
   BL3-1 and BL3-2 are the images which received the biggest allocations
   since they will most probably grow the most.

This patch also adds instruction synchronization barriers around the code which
handles the timer interrupt in the TSP. This ensures that the interrupt is not
acknowledged after or EOIed before it is deactivated at the peripheral.

Change-Id: I1c5b51858700027ee283ac85d18e06863a27c72e

Move the TSP private declarations out of tsp.h and into a new
header, tsp_private.h. This clarifies the TSP interface to the TSPD.

Change-Id: I39af346eeba3350cadcac56c02d97a5cb978c28b

Exclude stdlib files because they do not follow kernel code style.

Fixes ARM-software/tf-issues#73

Change-Id: I4cfafa38ab436f5ab22c277cb38f884346a267ab

Previously, platform.h contained many declarations and definitions
used for different purposes. This file has been split so that:

* Platform definitions used by common code that must be defined
  by the platform are now in platform_def.h. The exact include
  path is exported through $PLAT_INCLUDES in the platform makefile.

* Platform definitions specific to the FVP platform are now in
  /plat/fvp/fvp_def.h.

* Platform API declarations specific to the FVP platform are now
  in /plat/fvp/fvp_private.h.

* The remaining platform API declarations that must be ported by
  each platform are still in platform.h but this file has been
  moved to /include/plat/common since this can be shared by all
  platforms.

Change-Id: Ieb3bb22fbab3ee8027413c6b39a783534aee474a

This patch adds support in the TSP to program the secure physical
generic timer to generate a EL-1 interrupt every half second. It also
adds support for maintaining the timer state across power management
operations. The TSPD ensures that S-EL1 can access the timer by
programming the SCR_EL3.ST bit.

This patch does not actually enable the timer. This will be done in a
subsequent patch once the complete framework for handling S-EL1
interrupts is in place.

Change-Id: I1b3985cfb50262f60824be3a51c6314ce90571bc

The issues addressed in this patch are:

1. Remove meminfo_t from the common interfaces in BL3-x,
expecting that platform code will find a suitable mechanism
to determine the memory extents in these images and provide
it to the BL3-x images.

2. Remove meminfo_t and bl31_plat_params_t from all FVP BL3-x
code as the images use link-time information to determine
memory extents.

meminfo_t is still used by common interface in BL1/BL2 for
loading images

Change-Id: I4e825ebf6f515b59d84dc2bdddf6edbf15e2d60f

Instead of having a single version of the MMU setup functions for all
bootloader images that can execute either in EL3 or in EL1, provide
separate functions for EL1 and EL3. Each bootloader image can then
call the appropriate version of these functions. The aim is to reduce
the amount of code compiled in each BL image by embedding only what's
needed (e.g. BL1 to embed only EL3 variants).

Change-Id: Ib86831d5450cf778ae78c9c1f7553fe91274c2fa

This patch moves console_init() to bl32_early_platform_setup(). It
also ensures that console_init() is called in each
blX_early_platform_setup() function before the console is used
e.g. through a printf call in an assert() statement.

Fixes ARM-software/TF-issues#127

Change-Id: I5b1f17e0152bab674d807d2a95ff3689c5d4794e

Reduce the number of header files included from other header
files as much as possible without splitting the files. Use forward
declarations where possible. This allows removal of some unnecessary
"#ifndef __ASSEMBLY__" statements.

Also, review the .c and .S files for which header files really need
including and reorder the #include statements alphabetically.

Fixes ARM-software/tf-issues#31

Change-Id: Iec92fb976334c77453e010b60bcf56f3be72bd3e

Add tag names to all unnamed structs in header files. This
allows forward declaration of structs, which is necessary to
reduce header file nesting (to be implemented in a subsequent
commit).

Also change the typedef names across the codebase to use the _t
suffix to be more conformant with the Linux coding style. The
coding style actually prefers us not to use typedefs at all but
this is considered a step too far for Trusted Firmware.

Also change the IO framework structs defintions to use typedef'd
structs to be consistent with the rest of the codebase.

Change-Id: I722b2c86fc0d92e4da3b15e5cab20373dd26786f

This patch adds a simple TSP as the BL3-2 image. The secure payload
executes in S-EL1. It paves the way for the addition of the TSP
dispatcher runtime service to BL3-1. The TSP and the dispatcher service
will serve as an example of the runtime firmware's ability to toggle
execution between the non-secure and secure states in response to SMC
request from the non-secure state.  The TSP will be replaced by a
Trusted OS in a real system.

The TSP also exports a set of handlers which should be called in
response to a PSCI power management event e.g a cpu being suspended or
turned off. For now it runs out of Secure DRAM on the ARM FVP port and
will be moved to Secure SRAM later. The default translation table setup
code assumes that the caller is executing out of secure SRAM. Hence the
TSP exports its own translation table setup function.

The TSP only services Fast SMCs, is non-reentrant and non-interruptible.
It does arithmetic operations on two sets of four operands, one set
supplied by the non-secure client, and the other supplied by the TSP
dispatcher in EL3. It returns the result according to the Secure Monitor
Calling convention standard.

This TSP has two functional entry points:

- An initial, one-time entry point through which the TSP is initialized
  and prepares for receiving further requests from secure
  monitor/dispatcher

- A fast SMC service entry point through which the TSP dispatcher
  requests secure services on behalf of the non-secure client

Change-Id: I24377df53399307e2560a025eb2c82ce98ab3931
Co-authored-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch adds the ability to specify the base address of a UART
device for initialising the console. This allows a boot loader stage
to use a different UART device from UART0 (default) for the console.

Change-Id: Ie60b927389ae26085cfc90d22a564ff83ba62955