GitLab

The main difference between HiKey960 v1 hardware and HiKey960 v2
hardware is on UART console.

But the function of detecting boardid dumps message before console
ready. So fix it by removing those messages.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Create hikey_bl_common.c to store duplicated initialization
code in BL1 and BL2.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Since non-TF ROM is used in HiKey platform (Hisilicon Hi6220 SoC),
replace BL1 by BL2_EL3 in normal boot mode.

When we recovery images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Although SRAM is initialized, DCACHE should be cleaned too.
Because MCU is a parrallel core to access SRAM. We need to make
sure that initialized value is really written to SRAM before
MCU using it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Since LOAD_IMAGE_V2 is always enabled in HiKey platform. Drop
LOAD_IMAGE v1 to simplify code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

MAP_TSP_MEM could be either in SRAM or DRAM. When MAP_TSP_MEM is in
DRAM, it's overlapped with MAP_DDR.

Since MAP_OPTEE_PAGEABLE isn't used in SRAM case, just remove it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

SPM: Map devices in the 1st GB

Fix documentation for CnP bit

docs: hikey: Fix typo

The CnP bit documentation in the Firmware Design Guide incorrectly
used the term "Page Entries" instead of "Processing Elements".
Fix that.

Change-Id: Ie44ee99c281b7b1a9ad90fba2c7d109f12425507
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

hikey: fix assert in sec_protect()

This patch maps the devices in the first GB of the system address map
on the FVP into the S-EL1&0 translation regime when SPM support is
enabled. This grants the Secure Partition access to the devices in
this region, for example the memory-mapped Generic Timer device.

Change-Id: I3aeea65f859ecbe83efde2acee20c55500c451bc
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

The correct name of the manufacturer is LeMaker.
Signed-off-by: Andreas Färber <afaerber@suse.de>

`assert(e)` was used in place of `if (e) ERROR()` when sec_protect()
was ported from hikey fork so the logic should have been reversed.

Fixes: 3d5d9f5a ("hikey: configure the top 16MB of DRAM as secure")
Fixes: 52988b38

 ("hikey: configure 4 MB of secure DRAM for OP-TEE
Secure Data Path")
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Victor Chong <victor.chong@linaro.org>

Hikey protect optee / sdp memory

uniphier: migrate to BL2-AT-EL3

SPM: Declare explicit width based types in secure_partition_boot_info…

Hikey960: Enable invalid FIQ handling

Workarounds for CVE-2017-5715 on A9/A15 and A17 + serial console reporting

poplar: Enable emmc and recovery build support

New console API and coreboot support [v4]

UniPhier platform implements non-TF boot ROM.  Prior to the BL2-AT-EL3
support, BL1 (worked as a pseudo ROM) was needed just for ensuring BL2
is entered at EL1-S.  Now, this platform is able to avoid this waste.

Enable the BL2_AT_EL3 option, and remove BL1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The warm boot mailbox code is compiled if PROGRAMMABLE_RESET_ADDRESS
is disabled.

The warm boot mailbox is useless for UniPhier SoC family because BL1
is not the first image.  The UniPhier platform implements non-TF ROM,
then BL1 works as a pseudo ROM, so it is never executed in the warm
boot.

The reset vector address is not actually programmable for UniPhier
platform, but it should not hurt to enable PROGRAMMABLE_RESET_ADDRESS
to disable the mailbox and remove pointless plat_get_my_entrypoint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Allow API deprecation for uniphier platform

Update the memory firewall configuration to reserve 4 MB of secure RAM
for use by the kernel and OP-TEE as the Secure Data Path pool.
Note that this address range (0x3E800000 - 0x3EC00000) falls in the
range already set aside by UEFI (which reserves the upper 32 MB of the
1GB DRAM for OP-TEE [1]) and was previously unused.

[1] https://github.com/96boards-hikey/edk2/blob/hikey/HisiPkg/HiKeyPkg/Library/HiKeyLib/HiKeyMem.c#L44

Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Victor Chong <victor.chong@linaro.org>

DRAM region 0x3f000000 - 0x3fffffff is reserved for OP-TEE and should
therefore be accessible only from secure world.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Victor Chong <victor.chong@linaro.org>

The secure_partition_boot_info_t structure is used to communicate boot
parameters with the StandaloneMM code executing at S-EL0 through a
shared buffer. Certain data types used for members of this structure
are opaque with their size depending on the toolchain being used.

Declare the members of the structure with explicit width based data
types, which would maintain compatibility across toolchains.
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

The `override ERROR_DEPRECATION = 1` setting in uniphier platform
makes deprecation of API difficult. Hence removing the same. This
flag should be specified on the command line if needed.

Change-Id: I8c82d8d13944e450a8cd636de3326137c04d7560
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Let bl1 and bl2 have the ability to load images from emmc instead of
dram (mmap).
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

When some interrupts are configured as group 0 in GICv2, these
interrupts trigger FIQ signal; this results in the Linux kernel panic
by reporting log: "Bad mode in FIQ handler detected on CPU0, code
0x00000000 -- Unknown/Uncategorized".  Unfortunately from kernel side it
has no permission to read the GIC register for group 0 interrupts so we
have no chance to get to know which interrupt is configured as secure
interrupt and cause the kernel panic.

For upper reason, this commit enables FIQ exception handling for
SPD_none case.  If the system has not enabled SPD the FIQ interrupt is
trapped into EL3 and the FIQ handler can report the interrupt number so
we can easily narrow down which FIQ introduce unexpected interrupt.
After enable SPD we can rely on SPD interrupt route model to handle FIQ.
Signed-off-by: Leo Yan <leo.yan@linaro.org>

lib/cpus: fix branching in reset function for cortex-a72 AARCH32 mode

emmc: add macros CMD21, BUS_WIDTH_DDR_4 and BUS_WIDTH_DDR_8

coreboot supports an in-memory console to store firmware logs even when
no serial console is available. It is widely supported by
coreboot-compatible bootloaders (including SeaBIOS and GRUB) and can be
read by the Linux kernel.

This patch allows BL31 to add its own log messages to this console. The
driver will be registered automatically if coreboot support is compiled
in and detects the presence of a console buffer in the coreboot tables.

Change-Id: I31254dfa0c2fdeb7454634134b5707b4b4154907
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch changes all Rockchip platforms to use the new
MULTI_CONSOLE_API. The platform-specific plat_crash_console
implementations are removed so that the platform can use the ones from
the common platform code instead.

Also change the registers used in plat_crash_print_regs. The existing
use of x16 and x17 has always been illegal, since those registers are
reserved for use by the linker as a temporary scratch registers in
intra-procedure-call veneers and can never be expected to maintain their
values across a function call.

Change-Id: I8249424150be8d5543ed4af93b56756795a5288f
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch changes all Rockchip platforms to initialize the serial
console with information supplied by coreboot rather than hardcoded
base address and divisor values if BL31 is run on top of coreboot.
Moving the BL2-to-BL31 parameter parsing as early as possible to ensure
that the console is available for all following code.

Also update the Rockchip platform to use MULTI_CONSOLE_API.

Change-Id: I670d350fa2f8b8133539f91ac14977ab47db60d9
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch adds the foundation for a platform-independent coreboot
support library that can be shared by all platforms that boot BL31 from
coreboot (acting as BL2). It adds code to parse the "coreboot table", a
data structure that coreboot uses to communicate different kinds of
information to later-stage firmware and certain OS drivers.

As a first small use case for this information, allow platforms to
access the serial console configuration used by coreboot, removing the
need to hardcode base address and divisors and allowing Trusted Firmware
to benefit from coreboot's user configuration (e.g. which UART to pick
and which baud rate to use).

Change-Id: I2bfb39cd2609ce6640b844ab68df6c9ae3f28e9e
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch updates the Cadence CDNS console driver to support the new
console API. The driver will continue to support the old API as well by
checking the MULTI_CONSOLE_API compile-time flag.

Change-Id: I2ef8fb0d6ab72696997db1e0243a533499569d6b
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch updates the ARM PL011 console driver to support the new
console API. The driver will continue to support the old API as well by
checking the MULTI_CONSOLE_API compile-time flag.

Change-Id: Ic34e4158addbb0c5fae500c9cff899c05a4f4206
Signed-off-by: Julius Werner <jwerner@chromium.org>

This patch updates the TI 16550 console driver to support the new
console API. The driver will continue to support the old API as well by
checking the MULTI_CONSOLE_API compile-time flag.

Change-Id: I60a44b7ba3c35c74561824c04b8dbe3e3039324c
Signed-off-by: Julius Werner <jwerner@chromium.org>